X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32l4x.cfg;h=dabdacd4173e527a8d93cfa695a37dc2ff4c98c3;hb=e6505b04892ccacf75603c3d173616f5d92809e7;hp=103d741e2b73c7383389200433260ef986e99db8;hpb=d47aaf6d92788efc90c6d3379d58132e7ddfa781;p=fw%2Fopenocd

diff --git a/tcl/target/stm32l4x.cfg b/tcl/target/stm32l4x.cfg
index 103d741e2..dabdacd41 100644
--- a/tcl/target/stm32l4x.cfg
+++ b/tcl/target/stm32l4x.cfg
@@ -1,3 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 # script for stm32l4x family
 
 #
@@ -38,6 +40,8 @@ if { [info exists CPUTAPID] } {
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
+
 if {[using_jtag]} {
    jtag newtap $_CHIPNAME bs -irlen 5
 }
@@ -47,8 +51,9 @@ target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
-flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
-flash bank $_CHIPNAME.otp   stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME stm32l4x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
 
 if { [info exists QUADSPI] && $QUADSPI } {
    set a [llength [flash list]]
@@ -88,12 +93,54 @@ if {![using_hla]} {
    cortex_m reset_config sysresetreq
 }
 
+$_TARGETNAME configure -event examine-end {
+	# Enable debug during low power modes (uses more power)
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+	mmw 0xE0042004 0x00000007 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+	mmw 0xE0042008 0x00001800 0
+}
+
+proc proc_post_enable {_chipname} {
+	targets $_chipname.cpu
+
+	if { [$_chipname.tpiu cget -protocol] eq "sync" } {
+		switch [$_chipname.tpiu cget -port-width] {
+			1 {
+				mmw 0xE0042004 0x00000060 0x000000c0
+				mmw 0x48001020 0x00000000 0x0000ff00
+				mmw 0x48001000 0x000000a0 0x000000f0
+				mmw 0x48001008 0x000000f0 0x00000000
+			  }
+			2 {
+				mmw 0xE0042004 0x000000a0 0x000000c0
+				mmw 0x48001020 0x00000000 0x000fff00
+				mmw 0x48001000 0x000002a0 0x000003f0
+				mmw 0x48001008 0x000003f0 0x00000000
+			  }
+			4 {
+				mmw 0xE0042004 0x000000e0 0x000000c0
+				mmw 0x48001020 0x00000000 0x0fffff00
+				mmw 0x48001000 0x00002aa0 0x00003ff0
+				mmw 0x48001008 0x00003ff0 0x00000000
+			  }
+		}
+	} else {
+		mmw 0xE0042004 0x00000020 0x000000c0
+	}
+}
+
+$_CHIPNAME.tpiu configure -event post-enable "proc_post_enable $_CHIPNAME"
+
 $_TARGETNAME configure -event reset-init {
 	# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 6 (4 MHz).
 	# Use MSI 24 MHz clock, compliant even with VOS == 2.
 	# 3 WS compliant with VOS == 2 and 24 MHz.
 	mww 0x40022000 0x00000103   ;# FLASH_ACR = PRFTBE | 3(Latency)
 	mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
+
 	# Boost JTAG frequency
 	adapter speed 4000
 }
@@ -102,19 +149,3 @@ $_TARGETNAME configure -event reset-start {
 	# Reset clock is MSI (4 MHz)
 	adapter speed 500
 }
-
-$_TARGETNAME configure -event examine-end {
-	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
-	mmw 0xE0042004 0x00000007 0
-
-	# Stop watchdog counters during halt
-	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
-	mmw 0xE0042008 0x00001800 0
-}
-
-$_TARGETNAME configure -event trace-config {
-	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
-	# change this value accordingly to configure trace pins
-	# assignment
-	mmw 0xE0042004 0x00000020 0
-}