X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32l4x.cfg;h=103d741e2b73c7383389200433260ef986e99db8;hb=d47aaf6d92788efc90c6d3379d58132e7ddfa781;hp=496b47a72b6e4ce3640ea99e1d337799f832c8f0;hpb=2231da8ec4e7d7ae9b652f3dd1a7104f5a110f3f;p=fw%2Fopenocd

diff --git a/tcl/target/stm32l4x.cfg b/tcl/target/stm32l4x.cfg
index 496b47a72..103d741e2 100644
--- a/tcl/target/stm32l4x.cfg
+++ b/tcl/target/stm32l4x.cfg
@@ -15,11 +15,11 @@ if { [info exists CHIPNAME] } {
 set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
-# Smallest current target has 64kB ram, use 32kB by default to avoid surprises
+# By default use 40kB (Available RAM in smallest device STM32L412)
 if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set _WORKAREASIZE 0x8000
+   set _WORKAREASIZE 0xa000
 }
 
 #jtag scan chain
@@ -47,8 +47,25 @@ target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp   stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
+
+if { [info exists QUADSPI] && $QUADSPI } {
+   set a [llength [flash list]]
+   set _QSPINAME $_CHIPNAME.qspi
+   flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+} else {
+   if { [info exists OCTOSPI1] && $OCTOSPI1 } {
+      set a [llength [flash list]]
+      set _OCTOSPINAME1 $_CHIPNAME.octospi1
+      flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+   }
+   if { [info exists OCTOSPI2] && $OCTOSPI2 } {
+      set b [llength [flash list]]
+      set _OCTOSPINAME2 $_CHIPNAME.octospi2
+      flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_TARGETNAME 0xA0001400
+   }
+}
 
 # Common knowledges tells JTAG speed should be <= F_CPU/6.
 # F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
@@ -56,9 +73,9 @@ flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
 #
 # Note that there is a pretty wide band where things are
 # more or less stable, see http://openocd.zylin.com/#/c/3366/
-adapter_khz 500
+adapter speed 500
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -78,12 +95,12 @@ $_TARGETNAME configure -event reset-init {
 	mww 0x40022000 0x00000103   ;# FLASH_ACR = PRFTBE | 3(Latency)
 	mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
 	# Boost JTAG frequency
-	adapter_khz 4000
+	adapter speed 4000
 }
 
 $_TARGETNAME configure -event reset-start {
 	# Reset clock is MSI (4 MHz)
-	adapter_khz 500
+	adapter speed 500
 }
 
 $_TARGETNAME configure -event examine-end {