X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32f4x.cfg;h=aa2816e76a4e363e9ffb3dbb250aab4f5927c5f6;hb=69ea481e0b3607085cc05cbc5ca41740c9f938f6;hp=14fc2ffbed5111848e07a09120fdc59c009dab85;hpb=66d29eb6e3041146e2bb316d0e471e69d781b07d;p=fw%2Fopenocd

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index 14fc2ffbe..aa2816e76 100644
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -1,7 +1,7 @@
 # script for stm32f4x family
 
 #
-# stm32 devices support both JTAG and SWD transports.
+# stm32f4 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
 source [find mem_helper.tcl]
@@ -36,49 +36,39 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0090
-  # Section 38.6.2
-  # STM32F405xx/07xx and STM32F415xx/17xx
-  set _BSTAPID1 0x06413041
-  # STM32F42xxx and STM32F43xxx
-  set _BSTAPID2 0x06419041
-  # See STM Document RM0368 (Rev. 3)
-  # STM32F401B/C
-  set _BSTAPID3 0x06423041
-  # STM32F401D/E
-  set _BSTAPID4 0x06433041
-  # See STM Document RM0383 (Rev 2)
-  # STM32F411
-  set _BSTAPID5 0x06431041
-}
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-     -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-     -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
+flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
+
+if { [info exists QUADSPI] && $QUADSPI } {
+   set a [llength [flash list]]
+   set _QSPINAME $_CHIPNAME.qspi
+   flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+}
+
 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
 #
 # Since we may be running of an RC oscilator, we crank down the speed a
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-adapter_khz 2000
+adapter speed 2000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -101,13 +91,37 @@ $_TARGETNAME configure -event examine-end {
 	mmw 0xE0042008 0x00001800 0
 }
 
-$_TARGETNAME configure -event trace-config {
-	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
-	# change this value accordingly to configure trace pins
-	# assignment
-	mmw 0xE0042004 0x00000020 0
+proc proc_post_enable {_chipname} {
+	targets $_chipname.cpu
+
+	if { [$_chipname.tpiu cget -protocol] eq "sync" } {
+		switch [$_chipname.tpiu cget -port-width] {
+			1 {
+				mmw 0xE0042004 0x00000060 0x000000c0
+				mmw 0x40021020 0x00000000 0x0000ff00
+				mmw 0x40021000 0x000000a0 0x000000f0
+				mmw 0x40021008 0x000000f0 0x00000000
+			  }
+			2 {
+				mmw 0xE0042004 0x000000a0 0x000000c0
+				mmw 0x40021020 0x00000000 0x000fff00
+				mmw 0x40021000 0x000002a0 0x000003f0
+				mmw 0x40021008 0x000003f0 0x00000000
+			  }
+			4 {
+				mmw 0xE0042004 0x000000e0 0x000000c0
+				mmw 0x40021020 0x00000000 0x0fffff00
+				mmw 0x40021000 0x00002aa0 0x00003ff0
+				mmw 0x40021008 0x00003ff0 0x00000000
+			  }
+		}
+	} else {
+		mmw 0xE0042004 0x00000020 0x000000c0
+	}
 }
 
+$_CHIPNAME.tpiu configure -event post-enable "proc_post_enable $_CHIPNAME"
+
 $_TARGETNAME configure -event reset-init {
 	# Configure PLL to boost clock to HSI x 4 (64 MHz)
 	mww 0x40023804 0x08012008   ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
@@ -118,10 +132,10 @@ $_TARGETNAME configure -event reset-init {
 	mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
 
 	# Boost JTAG frequency
-	adapter_khz 8000
+	adapter speed 8000
 }
 
 $_TARGETNAME configure -event reset-start {
 	# Reduce speed since CPU speed will slow down to 16MHz with the reset
-	adapter_khz 2000
+	adapter speed 2000
 }