X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32f2x.cfg;h=d790febd56464ede05c66838acb014c1fe285a1c;hb=d1278660afcb3315fe74def3c2ca51cf28424963;hp=0ac73a519988996a463f7e8c911a790632f47967;hpb=a1bbf4b75bc68aeed3c72e37b302bb36757401c2;p=fw%2Fopenocd

diff --git a/tcl/target/stm32f2x.cfg b/tcl/target/stm32f2x.cfg
index 0ac73a519..d790febd5 100644
--- a/tcl/target/stm32f2x.cfg
+++ b/tcl/target/stm32f2x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -27,9 +28,9 @@ if { [info exists WORKAREASIZE] } {
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-adapter_khz 1000
+adapter speed 1000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -48,27 +49,20 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0033
-  # Section 32.6.2
-  # 
-  set _BSTAPID 0x06411041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+	jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
 
 reset_config srst_nogate
 
@@ -77,3 +71,19 @@ if {![using_hla]} {
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+	mmw 0xE0042004 0x00000007 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+	mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+	# change this value accordingly to configure trace pins
+	# assignment
+	mmw 0xE0042004 0x00000020 0
+}