X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fklx.cfg;h=84f6535e35ed7ae7484ddf03f31af245bb11aad7;hb=385eedfc6f0b82c5d6715c740ee40bdce983ef04;hp=0df6612f708d93a9919e6feabf669f0765c784f3;hpb=6d5b4d709cb05e8daf0350ac507b928da95d0abb;p=fw%2Fopenocd

diff --git a/tcl/target/klx.cfg b/tcl/target/klx.cfg
index 0df6612f7..84f6535e3 100644
--- a/tcl/target/klx.cfg
+++ b/tcl/target/klx.cfg
@@ -1,5 +1,6 @@
 #
-# Freescale Kinetis KL series devices
+# NXP (former Freescale) Kinetis KL series devices
+# Also used for Cortex-M0+ equipped members of KVx and KE1xZ series
 #
 
 source [find target/swj-dp.tcl]
@@ -11,11 +12,11 @@ if { [info exists CHIPNAME] } {
 }
 
 # Work-area is a space in RAM used for flash programming
-# By default use 4kB
+# By default use 1KiB
 if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set _WORKAREASIZE 0x1000
+   set _WORKAREASIZE 0x400
 }
 
 if { [info exists CPUTAPID] } {
@@ -25,24 +26,39 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -chain-position $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.pflash
 flash bank $_FLASHNAME kinetis 0 0 0 0 $_TARGETNAME
+kinetis create_banks
 
 # Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
-# specifies up to 1MHz for VLPR mode.
-adapter_khz 1000
+# specifies up to 1MHz for VLPR mode and up to 24MHz for run mode;
+# Table 17 of Sub-Family Data Sheet rev4 lists 25MHz as the maximum frequency.
+adapter speed 1000
 
 reset_config srst_nogate
 
-if {![using_hla]} {
-   # Detect secured MCU or boot lock-up in RESET/WDOG loop
-   $_CHIPNAME.cpu configure -event examine-start {
+if {[using_hla]} {
+   echo ""
+   echo "!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!"
+   echo " Kinetis MCUs have a MDM-AP dedicated mainly to MCU security related functions."
+   echo " A high level adapter (like a ST-Link) you are currently using cannot access"
+   echo " the MDM-AP, so commands like 'mdm mass_erase' are not available in your"
+   echo " configuration. Also security locked state of the device will not be reported."
+   echo ""
+   echo " Be very careful as you can lock the device though there is no way to unlock"
+   echo " it without mass erase. Don't set write protection on the first block."
+   echo "!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!"
+   echo ""
+} else {
+   # Detect secured MCU
+   $_TARGETNAME configure -event examine-fail {
       kinetis mdm check_security
    }
 
@@ -51,10 +67,9 @@ if {![using_hla]} {
    cortex_m reset_config sysresetreq
 }
 
-# Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
-# specifies up to 24MHz for run mode; Table 17 of Sub-Family Data
-# Sheet rev4 lists 25MHz as the maximum frequency.
-# Uncoment only if VLPR mode is not used
-#$_TARGETNAME configure -event reset-init {
-#   adapter_khz 24000
-#}
+# Disable watchdog not to disturb OpenOCD algorithms running on MCU
+# (e.g. armv7m_checksum_memory() in verify_image)
+# Flash driver also disables watchdog before FTFA flash programming.
+$_TARGETNAME configure -event reset-init {
+   kinetis disable_wdog
+}