X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Fkl25.cfg;h=0e716e3ae2b243fd197538e4f7295a8a5cb43fce;hb=afbad69d97938b8c35d7d416e38403cb4e58f803;hp=7b14ecc8ec17a25dc496ae2ba16854a271d4c748;hpb=c7384117c66e8f18896ca09ab8095d6da16bb1e5;p=fw%2Fopenocd

diff --git a/tcl/target/kl25.cfg b/tcl/target/kl25.cfg
index 7b14ecc8e..0e716e3ae 100644
--- a/tcl/target/kl25.cfg
+++ b/tcl/target/kl25.cfg
@@ -2,68 +2,5 @@
 # Freescale Kinetis KL25 devices
 #
 
-#
-# KL25 devices support both JTAG and SWD transports.
-#
-source [find target/swj-dp.tcl]
-
-if { [info exists CHIPNAME] } {
-    set _CHIPNAME $CHIPNAME
-} else {
-    set _CHIPNAME kl25
-}
-
-if { [info exists ENDIAN] } {
-    set _ENDIAN $ENDIAN
-} else {
-    set _ENDIAN little
-}
-
-# Work-area is a space in RAM used for flash programming
-# By default use 4kB
-if { [info exists WORKAREASIZE] } {
-   set _WORKAREASIZE $WORKAREASIZE
-} else {
-   set _WORKAREASIZE 0x1000
-}
-
-if { [info exists CPUTAPID] } {
-    set _CPUTAPID $CPUTAPID
-} else {
-    set _CPUTAPID 0x0bc11477
-}
-
-swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_CHIPNAME.cpu
-
-# It is important that "kinetis mdm check_security" is called for
-# 'examine-end' event and not 'eximine-start'. Calling it in 'examine-start'
-# causes "kinetis mdm check_security" to fail the first time openocd
-# calls it when it tries to connect after the CPU has been power-cycled.
-$_CHIPNAME.cpu configure -event examine-end {
-	kinetis mdm check_security
-}
-
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME kinetis 0 0 0 0 $_TARGETNAME
-
-# Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
-# specifies up to 1MHz for VLPR mode.
-adapter_khz 1000
-
-if {![using_hla]} {
-   # if srst is not fitted use SYSRESETREQ to
-   # perform a soft reset
-   cortex_m reset_config sysresetreq
-}
-
-$_TARGETNAME configure -event reset-init {
-    # Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
-    # specifies up to 24MHz for run mode; Table 17 of Sub-Family Data
-    # Sheet rev4 lists 25MHz as the maximum frequency.
-    adapter_khz 24000
-}
+set CHIPNAME kl25
+source [find target/klx.cfg]