X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Ftarget%2Faduc702x.cfg;h=c9037100fe7ce5da96118944fd7f7749c66da319;hb=e6505b04892ccacf75603c3d173616f5d92809e7;hp=ef1beb78d801fd3c4ee99a48ea17f7b4278bca56;hpb=dbbc9c41f7db210b0a4e226540a28e0a8a5019bf;p=fw%2Fopenocd

diff --git a/tcl/target/aduc702x.cfg b/tcl/target/aduc702x.cfg
index ef1beb78d..c9037100f 100644
--- a/tcl/target/aduc702x.cfg
+++ b/tcl/target/aduc702x.cfg
@@ -1,34 +1,27 @@
-## -*- tcl -*-
-##
-
+# SPDX-License-Identifier: GPL-2.0-or-later
 
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
-   set  _CHIPNAME s3c2410
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME aduc702x
 }
 
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
-  # This config file was defaulting to big endian..
-   set  _ENDIAN little
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   # This config file was defaulting to big endian..
+   set _ENDIAN little
 }
 
-if { [info exists CPUTAPID] } {	
-   set  _CPUTAPID $CPUTAPID    
-} else {	 
-   set  _CPUTAPID 0xffffffff
+if { [info exists CPUTAPID] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x3f0f0f0f
 }
 
-
-jtag_nsrst_delay 200
+adapter srst delay 200
 jtag_ntrst_delay 200
 
-# This is for the case that TRST/SRST is not wired on your JTAG adaptor.
-# Don't really need them anyways.  
-reset_config none
-
 ## JTAG scan chain
 #format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
@@ -36,7 +29,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP
 ##
 ## Target configuration
 ##
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
 
 # allocate the entire SRAM as working area
@@ -44,7 +37,8 @@ $_TARGETNAME configure -work-area-phys 0x10000 -work-area-size 0x2000
 
 ## flash configuration
 # only target number is needed
-flash bank aduc702x 0 0 0 0 0
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME aduc702x 0 0 0 0 $_TARGETNAME
 
 ## If you use the watchdog, the following code makes sure that the board
 ## doesn't reboot when halted via JTAG.  Yes, on the older generation
@@ -53,9 +47,9 @@ flash bank aduc702x 0 0 0 0 0
 proc watchdog_service {} {
     global watchdog_hdl
     mww 0xffff036c 0
-#    puts "watchdog!!"
+#    echo "watchdog!!"
     set watchdog_hdl [after 500 watchdog_service]
 }
 
 $_TARGETNAME configure -event reset-halt-post {  watchdog_service }
-$_TARGETNAME configure -event old-pre_resume { global watchdog_hdl; after cancel $watchdog_hdl }
+$_TARGETNAME configure -event resume-start { global watchdog_hdl; after cancel $watchdog_hdl }