X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Fboard%2Ftp-link_tl-mr3020.cfg;h=1d1d627bc27738a515d683347527e59064ef4f4e;hb=4157732bd84c4e9e4b55357e1dc9a96078a35ee1;hp=b7d8d5b6150f57354e226cdca88d122f1ea5bab9;hpb=4517bcbd354206e2a9d132f80919617181059953;p=fw%2Fopenocd

diff --git a/tcl/board/tp-link_tl-mr3020.cfg b/tcl/board/tp-link_tl-mr3020.cfg
index b7d8d5b61..1d1d627bc 100644
--- a/tcl/board/tp-link_tl-mr3020.cfg
+++ b/tcl/board/tp-link_tl-mr3020.cfg
@@ -1,38 +1,6 @@
-source [find target/atheros_ar9331.cfg]
-
-proc ar9331_25mhz_pll_init {} {
-	mww 0xb8050008 0x00018004	;# bypass PLL; AHB_POST_DIV - ratio 4
-	mww 0xb8050004 0x00000352	;# 34000(ns)/40ns(25MHz) = 0x352 (850)
-	mww 0xb8050000 0x40818000	;# Power down control for CPU PLL
-					;# OUTDIV | REFDIV | DIV_INT
-	mww 0xb8050010 0x001003e8	;# CPU PLL Dither FRAC Register
-					;# (disabled?)
-	mww 0xb8050000 0x00818000	;# Power on | OUTDIV | REFDIV | DIV_INT
-	mww 0xb8050008 0x00008000	;# remove bypass;
-					;# AHB_POST_DIV - ratio 2
-}
-
-proc ar9331_ddr1_init {} {
-	mww 0xb8000000 0x7fbc8cd0       ;# DDR_CONFIG - lots of DRAM confs
-	mww 0xb8000004 0x9dd0e6a8	;# DDR_CONFIG2 - more DRAM confs
+# SPDX-License-Identifier: GPL-2.0-or-later
 
-	mww 0xb8000010 0x8	;# Forces a PRECHARGE ALL cycle
-	mww 0xb8000008 0x133	;# mode reg: 0x133 - default
-	mww 0xb8000010 0x1	;# Forces an MRS update cycl
-	mww 0xb800000c 0x2	;# Extended mode register value.
-				;# default 0x2 - Reset to weak driver, DLL on
-	mww 0xb8000010 0x2	;# Forces an EMRS update cycle
-	mww 0xb8000010 0x8	;# Forces a PRECHARGE ALL cycle
-	mww 0xb8000008 0x33	;# mode reg: remove some bit?
-	mww 0xb8000010 0x1	;# Forces an MRS update cycl
-	mww 0xb8000014 0x4186	;# enable refres: bit(14) - set refresh rate
-	mww 0xb800001c 0x8	;# This register is used along with DQ Lane 0,
-				;# DQ[7:0], DQS_0
-	mww 0xb8000020 0x9	;# This register is used along with DQ Lane 1,
-				;# DQ[15:8], DQS_1.
-	mww 0xb8000018 0xff	;# DDR read and capture bit mask.
-				;# Each bit represents a cycle of valid data.
-}
+source [find target/atheros_ar9331.cfg]
 
 $_TARGETNAME configure -event reset-init {
 	ar9331_25mhz_pll_init
@@ -42,3 +10,5 @@ $_TARGETNAME configure -event reset-init {
 
 set ram_boot_address 0xa0000000
 $_TARGETNAME configure -work-area-phys 0xa1FFE000 -work-area-size 0x1000
+
+flash bank flash0 ath79 0xbf000000 0 0 0 $_TARGETNAME cs0