X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Fboard%2Ftelo.cfg;h=721c01975d6442389ba9ee3d770299e2b7c2317a;hb=4157732bd84c4e9e4b55357e1dc9a96078a35ee1;hp=80040b1409cd847fdf54d809459d1665bf5f21aa;hpb=b559b273b526b3077b3ca219eecc8df9f86efac0;p=fw%2Fopenocd

diff --git a/tcl/board/telo.cfg b/tcl/board/telo.cfg
index 80040b140..721c01975 100644
--- a/tcl/board/telo.cfg
+++ b/tcl/board/telo.cfg
@@ -1,5 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 source [find target/c100.cfg]
-# basic register defintion for C100
+# basic register definition for C100
 source [find target/c100regs.tcl]
 # board-config info
 source [find target/c100config.tcl]
@@ -8,15 +10,12 @@ source [find target/c100helper.tcl]
 
 
 # Telo board & C100 support trst and srst
-# Note that libftd2xx.so tries to assert srst
-# which break this script
-# use libftdi.so library instead with this script
 # make the reset asserted to
 # allow RC circuit to discharge for: [ms]
-jtag_nsrst_assert_width 100
+adapter srst pulse_width 100
 jtag_ntrst_assert_width 100
 # don't talk to JTAG after reset for: [ms]
-adapter_nsrst_delay 100
+adapter srst delay 100
 jtag_ntrst_delay 100
 reset_config trst_and_srst separate
 
@@ -26,29 +25,29 @@ reset_config trst_and_srst separate
 # issue telnet: reset init
 # issue gdb: monitor reset init
 $_TARGETNAME configure -event reset-init {
-	adapter_khz 100
+	adapter speed 100
 	# this will setup Telo board
 	setupTelo
 	#turn up the JTAG speed
-	adapter_khz 3000
-	puts "JTAG speek now 3MHz"
-	puts "type helpC100 to get help on C100"
+	adapter speed 3000
+	echo "JTAG speek now 3MHz"
+	echo "type helpC100 to get help on C100"
 }
 
 $_TARGETNAME configure -event reset-deassert-post {
 	# Force target into ARM state.
-#	soft_reset_halt # not implemented on ARM11
-	puts "Detected SRSRT asserted on C100.CPU"
+#	soft_reset_halt ;# not implemented on ARM11
+	echo "Detected SRSRT asserted on C100.CPU"
 
 }
 
 $_TARGETNAME configure -event reset-assert-post {
-  puts "Assering reset"
+  echo "Assering reset"
   #sleep 10
 }
 
-proc power_restore {} { puts "Sensed power restore. No action." }
-proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }
+proc power_restore {} { echo "Sensed power restore. No action." }
+proc srst_deasserted {} { echo "Sensed nSRST deasserted. No action." }
 
 
 # boots from NOR on CS0:  8 MBytes CFI flash, 16-bit bus
@@ -58,4 +57,4 @@ set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
 
 # writing data to memory does not work without this
-memwrite burst disable
\ No newline at end of file
+arm11 memwrite burst disable