X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=tcl%2Fboard%2Fmini2440.cfg;h=85d9a35b9ac4918382cec1d14db7dd109e40ec29;hb=16cbddf1ce8b38bb5c2f02e438441572d285d946;hp=d17b1076b4968c63a3629241e1c15af4bd9d3fc8;hpb=3e6f9e8d1e65c4da505ff78481d54a115520d3d1;p=fw%2Fopenocd

diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index d17b1076b..85d9a35b9 100644
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -1,3 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 #-------------------------------------------------------------------------
 # Mini2440 Samsung s3c2440A Processor with 64MB DRAM, 64MB NAND, 2 MB N0R
 # NOTE: Configured for NAND boot (switch S2 in NANDBOOT)
@@ -38,7 +40,7 @@
 #     it's apt-get install libusb-dev.  When I made my config I only included
 #     --enable-jlink and --enable-usbdevs
 #
-#     I HAVE NOT Tested this throughly, so there could still be problems.
+#     I HAVE NOT Tested this thoroughly, so there could still be problems.
 #     But it should get you way ahead of the game from where I started.
 #     If you find problems (and fixes) please post them to
 #     openocd-development@lists.berlios.de and join the developers and
@@ -71,6 +73,11 @@
 #
 #
 #
+
+# FIXME use some standard target config, maybe create one from this
+#
+#	source [find target/...cfg]
+
 #-------------------------------------------------------------------------
 # Target configuration for the Samsung 2440 system on chip
 # Tested on a S3C2440 Evaluation board by keesj
@@ -92,22 +99,21 @@ if { [info exists ENDIAN] } {
    set  _ENDIAN little
 }
 
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # force an error till we get a good number
    set _CPUTAPID 0x0032409d
 }
 
 #jtag scan chain
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME
 $_TARGETNAME configure -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
 
 #reset configuration
-jtag_nsrst_delay 100
+adapter srst delay 100
 jtag_ntrst_delay 100
 reset_config trst_and_srst
 
@@ -116,8 +122,7 @@ reset_config trst_and_srst
 # IMPORTANT! See README at top of this file.
 #-------------------------------------------------------------------------
 
-    jtag_khz 12000
-    jtag interface
+    adapter speed 12000
 
 #-------------------------------------------------------------------------
 # GDB Setup
@@ -136,7 +141,7 @@ reset_config trst_and_srst
 
     nand device s3c2440 0
 
-    jtag_nsrst_delay 100
+    adapter srst delay 100
     jtag_ntrst_delay 100
     reset_config trst_and_srst
     init
@@ -177,10 +182,10 @@ proc init_2440 { } {
     # usb clock are off 12mHz xtal
     #-----------------------------------------------
 
-    mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
-    mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
-    mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
-    mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
+    mww phys 0x4C000014 0x00000005 ;#  Clock Divider control Reg
+    mww phys 0x4C000000 0xFFFFFFFF ;#  LOCKTIME count register
+    mww phys 0x4C000008 0x00038022 ;#  UPPLCON  USB clock config Reg
+    mww phys 0x4C000004 0x0007F021 ;#  MPPLCON  Proc clock config Reg
 
     #-----------------------------------------------
     # Configure Memory controller
@@ -188,45 +193,45 @@ proc init_2440 { } {
     # DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
     #-----------------------------------------------
 
-    mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
-    mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
-    mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
-    mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
-    mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
-    mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
-    mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
-    mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
+    mww phys 0x48000000 0x22111112 ;#  BWSCON - Bank and Bus Width
+    mww phys 0x48000010 0x00001112 ;#  BANKCON4 - ?
+    mww phys 0x4800001c 0x00018009 ;#  BANKCON6 - DRAM
+    mww phys 0x48000020 0x00018009 ;#  BANKCON7 - DRAM
+    mww phys 0x48000024 0x008E04EB ;#  REFRESH  - DRAM
+    mww phys 0x48000028 0x000000B2 ;#  BANKSIZE - DRAM
+    mww phys 0x4800002C 0x00000030 ;#  MRSRB6 - DRAM
+    mww phys 0x48000030 0x00000030 ;#  MRSRB7 - DRAM
 
     #-----------------------------------------------
     # Now port configuration for enables for memory
     # and other stuff.
     #-----------------------------------------------
 
-    mww phys 0x56000000	0x007FFFFF #  GPACON
+    mww phys 0x56000000	0x007FFFFF ;#  GPACON
 
-    mww phys 0x56000010	0x00295559 #  GPBCON
-    mww phys 0x56000018	0x000003FF #  GPBUP (PULLUP ENABLE)
-    mww phys 0x56000014	0x000007C2 #  GPBDAT
+    mww phys 0x56000010	0x00295559 ;#  GPBCON
+    mww phys 0x56000018	0x000003FF ;#  GPBUP (PULLUP ENABLE)
+    mww phys 0x56000014	0x000007C2 ;#  GPBDAT
 
-    mww phys 0x56000020	0xAAAAA6AA #  GPCCON
-    mww phys 0x56000028	0x0000FFFF #  GPCUP
-    mww phys 0x56000024	0x00000020 #  GPCDAT
+    mww phys 0x56000020	0xAAAAA6AA ;#  GPCCON
+    mww phys 0x56000028	0x0000FFFF ;#  GPCUP
+    mww phys 0x56000024	0x00000020 ;#  GPCDAT
 
-    mww phys 0x56000030	0xAAAAAAAA #  GPDCON
-    mww phys 0x56000038	0x0000FFFF #  GPDUP
+    mww phys 0x56000030	0xAAAAAAAA ;#  GPDCON
+    mww phys 0x56000038	0x0000FFFF ;#  GPDUP
 
-    mww phys 0x56000040	0xAAAAAAAA #  GPECON
-    mww phys 0x56000048	0x0000FFFF #  GPEUP
+    mww phys 0x56000040	0xAAAAAAAA ;#  GPECON
+    mww phys 0x56000048	0x0000FFFF ;#  GPEUP
 
-    mww phys 0x56000050	0x00001555 #  GPFCON
-    mww phys 0x56000058	0x0000007F #  GPFUP
-    mww phys 0x56000054	0x00000000 #  GPFDAT
+    mww phys 0x56000050	0x00001555 ;#  GPFCON
+    mww phys 0x56000058	0x0000007F ;#  GPFUP
+    mww phys 0x56000054	0x00000000 ;#  GPFDAT
 
-    mww phys 0x56000060	0x00150114 #  GPGCON
-    mww phys 0x56000068	0x0000007F #  GPGUP
+    mww phys 0x56000060	0x00150114 ;#  GPGCON
+    mww phys 0x56000068	0x0000007F ;#  GPGUP
 
-    mww phys 0x56000070	0x0015AAAA #  GPHCON
-    mww phys 0x56000078	0x000003FF #  GPGUP
+    mww phys 0x56000070	0x0015AAAA ;#  GPHCON
+    mww phys 0x56000078	0x000003FF ;#  GPGUP
 
 }
 
@@ -292,7 +297,7 @@ proc load_uboot { } {
 proc s {} {
         step
         reg
-        armv4_5 disassemble 0x33F80068 0x10
+        arm disassemble 0x33F80068 0x10
 }
 
 proc help_2440 {} {