X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=doc%2Fconfig-device.inc;h=a533ca82213debb5455671d278192640ac3d4bed;hb=8ec51d698921d07c394e6e0e48ac5d587f70ece8;hp=144b1e8fc9fd2704cefc91136e3ecea62361d1c8;hpb=6d80b89c0bd82133dd5c93df8604f562ac49c19a;p=fw%2Faltos

diff --git a/doc/config-device.inc b/doc/config-device.inc
index 144b1e8f..a533ca82 100644
--- a/doc/config-device.inc
+++ b/doc/config-device.inc
@@ -90,7 +90,7 @@ ifdef::radio[]
 		transmission is disabled.
 		ifdef::altusmetrum[]
 		This option is
-		available on TeleMetrum v2 and TeleMega
+		available on TeleMetrum v2 or newer and TeleMega
 		boards. TeleMetrum v1 boards cannot transmit
 		APRS packets.
 		endif::altusmetrum[]
@@ -118,6 +118,16 @@ ifdef::radio[]
 		altitude with Compressed format. Test before
 		you fly to see which to use.
 
+	==== APRS Offset
+	
+		The delay from the top of the minute before sending
+		the first APRS packet of the minute. Coordinating
+		values for this parameter between multiple devices can
+		allow a single receiver to reliably receive APRS
+		packets from multiple devices. Note that this offset only
+		takes effect while the GPS signal is locked so that the
+		transmitting device knows the current time.
+		
 	==== Callsign
 
 		This sets the call sign included in each
@@ -161,7 +171,11 @@ ifdef::altusmetrum[]
 		is fired first, followed after a two second
 		delay by the 'main' channel.
 
-	ifdef::telemetrum,telemega,easymega[]
+		Separation & Apogee::
+		This fires the 'main' channel when the first motor
+		burns out and fires the 'apogee' charge at apogee.
+
+	ifdef::telemetrum,telemega,easymega,easytimer[]
 	==== Pad Orientation
 
 		Because they include accelerometers,
@@ -173,15 +187,16 @@ ifdef::altusmetrum[]
 		with the antenna pointing aft instead.
 
 		Antenna Up::
-		In this mode, the antenna end of the flight
-		computer must point forward, in line with the
-		expected flight path.
+		In this mode, the antenna (or beeper, for devices
+		without an antenna) of the flight computer must point
+		forward, in line with the expected flight path.
 
 		Antenna Down::
-		In this mode, the antenna end of the flight
-		computer must point aft, in line with the
-		expected flight path.
-	endif::telemetrum,telemega,easymega[]
+
+		In this mode, the antenna (or beeper, for devices
+		without an antenna) end of the flight computer must
+		point aft, in line with the expected flight path.
+		endif::telemetrum,telemega,easymega,easytimer[]
 
 	==== Beeper Frequency
 
@@ -212,7 +227,7 @@ ifdef::telegps[]
 		in the log.
 endif::telegps[]
 
-ifdef::telemega,easymega,telemetrum[]
+ifdef::telemega,easymega,easytimer,telemetrum[]
 
 	==== Calibrate Accelerometer
 
@@ -226,9 +241,9 @@ ifdef::telemega,easymega,telemetrum[]
 		Configure Altimeter window and save the new
 		calibration values.
 
-endif::telemega,easymega,telemetrum[]
+endif::telemega,easymega,easytimer,telemetrum[]
 
-ifdef::telemega,easymega[]
+ifdef::telemega,easymega,easytimer[]
 
 	==== Configure Pyro Channels
 
@@ -236,8 +251,8 @@ ifdef::telemega,easymega[]
 		image::configure-pyro.png[width=400]
 
 		This opens a separate window to configure the
-		additional pyro channels available on TeleMega
-		and EasyMega.  One column is presented for
+		additional pyro channels available on TeleMega,
+		EasyMega and EasyTimer.  One column is presented for
 		each channel. Each row represents a single
 		parameter, if enabled the parameter must meet
 		the specified test for the pyro channel to be
@@ -264,4 +279,4 @@ ifdef::telemega,easymega[]
 
 		include::pyro-channels.adoc[]
 
-endif::telemega,easymega[]
+endif::telemega,easymega,easytimer[]