X-Git-Url: https://git.gag.com/?a=blobdiff_plain;f=doc%2Faltusmetrum.xsl;h=601b62eb16af5f8d891440194691f7db2028bb05;hb=998adccc1c4f8f6c44833bbf4a52d9441748b996;hp=88c9b80abb6264a786b907771c5fdf89dad5250e;hpb=a07b07d48f71b9a11e73a82db075cc57bad0c09f;p=fw%2Faltos
diff --git a/doc/altusmetrum.xsl b/doc/altusmetrum.xsl
index 88c9b80a..601b62eb 100644
--- a/doc/altusmetrum.xsl
+++ b/doc/altusmetrum.xsl
@@ -1810,6 +1810,220 @@ NAR #88757, TRA #12200
+
+ Altimeter Installation Recommendations
+
+ Building high-power rockets that fly safely is hard enough. Mix
+ in some sophisticated electronics and a bunch of radio energy
+ and oftentimes you find few perfect solutions. This chapter
+ contains some suggestions about how to install AltusMetrum
+ products into the rocket airframe, including how to safely and
+ reliably mix a variety of electronics into the same airframe.
+
+
+ Mounting the Altimeter
+
+ The first consideration is to ensure that the altimeter is
+ securely fastened to the airframe. For TeleMetrum, we use
+ nylon standoffs and nylon screws; they're good to at least 50G
+ and cannot cause any electrical issues on the board. For
+ TeleMini, we usually cut small pieces of 1/16" balsa to fit
+ under the screw holes, and then take 2x56 nylon screws and
+ screw them through the TeleMini mounting holes, through the
+ balsa and into the underlying material.
+
+
+
+ Make sure TeleMetrum is aligned precisely along the axis of
+ acceleration so that the accelerometer can accurately
+ capture data during the flight.
+
+
+ Watch for any metal touching components on the
+ board. Shorting out connections on the bottom of the board
+ can cause the altimeter to fail during flight.
+
+
+
+
+ Dealing with the Antenna
+
+ The antenna supplied is just a piece of solid, insulated,
+ wire. If it gets damaged or broken, it can be easily
+ replaced. It should be kept straight and not cut; bending or
+ cutting it will change the resonant frequency and/or
+ impedence, making it a less efficient radiator and thus
+ reducing the range of the telemetry signal.
+
+
+ Keeping metal away from the antenna will provide better range
+ and a more even radiation pattern. In most rockets, it's not
+ entirely possible to isolate the antenna from metal
+ components; there are often bolts, all-thread and wires from other
+ electronics to contend with. Just be aware that the more stuff
+ like this around the antenna, the lower the range.
+
+
+ Make sure the antenna is not inside a tube made or covered
+ with conducting material. Carbon fibre is the most common
+ culprit here -- CF is a good conductor and will effectively
+ shield the antenna, dramatically reducing signal strength and
+ range. Metalic flake paint is another effective shielding
+ material which is to be avoided around any antennas.
+
+
+ If the ebay is large enough, it can be convenient to simply
+ mount the altimeter at one end and stretch the antenna out
+ inside. Taping the antenna to the sled can keep it straight
+ under acceleration. If there are metal rods, keep the
+ antenna as far away as possible.
+
+
+ For a shorter ebay, it's quite practical to have the antenna
+ run through a bulkhead and into an adjacent bay. Drill a small
+ hole in the bulkhead, pass the antenna wire through it and
+ then seal it up with glue or clay. We've also used acrylic
+ tubing to create a cavity for the antenna wire. This works a
+ bit better in that the antenna is known to stay straight and
+ not get folded by recovery components in the bay. Angle the
+ tubing towards the side wall of the rocket and it ends up
+ consuming very little space.
+
+
+ If you need to place the antenna at a distance from the
+ altimeter, you can replace the antenna with an edge-mounted
+ SMA connector, and then run 50Ω coax from the board to the
+ antenna. Building a remote antenna is beyond the scope of this
+ manual.
+
+
+
+ Preserving GPS Reception
+
+ The GPS antenna and receiver in TeleMetrum are highly
+ sensitive and normally have no trouble tracking enough
+ satellites to provide accurate position information for
+ recovering the rocket. However, there are many ways to
+ attenuate the GPS signal.
+
+
+ Conductive tubing or coatings. Carbon fiber and metal
+ tubing, or metalic paint will all dramatically attenuate the
+ GPS signal. We've never heard of anyone successfully
+ receiving GPS from inside these materials.
+
+
+ Metal components near the GPS patch antenna. These will
+ de-tune the patch antenna, changing the resonant frequency
+ away from the L1 carrier and reduce the effectiveness of the
+ antenna. You can place as much stuff as you like beneath the
+ antenna as that's covered with a ground plane. But, keep
+ wires and metal out from above the patch antenna.
+
+
+
+
+
+ Radio Frequency Interference
+
+ Any altimeter will generate RFI; the digital circuits use
+ high-frequency clocks that spray radio interference across a
+ wide band. Altusmetrum altimeters generate intentional radio
+ signals as well, increasing the amount of RF energy around the board.
+
+
+ Rocketry altimeters also use precise sensors measuring air
+ pressure and acceleration. Tiny changes in voltage can cause
+ these sensor readings to vary by a huge amount. When the
+ sensors start mis-reporting data, the altimeter can either
+ fire the igniters at the wrong time, or not fire them at all.
+
+
+ Voltages are induced when radio frequency energy is
+ transmitted from one circuit to another. Here are things that
+ increase the induced voltage and current:
+
+
+
+ Keep wires from different circuits apart. Moving circuits
+ further apart will reduce RFI.
+
+
+ Avoid parallel wires from different circuits. The longer two
+ wires run parallel to one another, the larger the amount of
+ transferred energy. Cross wires at right angles to reduce
+ RFI.
+
+
+ Twist wires from the same circuits. Two wires the same
+ distance from the transmitter will get the same amount of
+ induced energy which will then cancel out. Any time you have
+ a wire pair running together, twist the pair together to
+ even out distances and reduce RFI. For altimeters, this
+ includes battery leads, switch hookups and igniter
+ circuits.
+
+
+ Avoid resonant lengths. Know what frequencies are present
+ in the environment and avoid having wire lengths near a
+ natural resonant length. Altusmetrum products transmit on the
+ 70cm amateur band, so you should avoid lengths that are a
+ simple ratio of that length; essentially any multiple of 1/4
+ of the wavelength (17.5cm).
+
+
+
+
+ The Barometric Sensor
+
+ Altusmetrum altimeters measure altitude with a barometric
+ sensor, essentially measuring the amount of air above the
+ rocket to figure out how high it is. A large number of
+ measurements are taken as the altimeter initializes itself to
+ figure out the pad altitude. Subsequent measurements are then
+ used to compute the height above the pad.
+
+
+ To accurately measure atmospheric pressure, the ebay
+ containing the altimeter must be vented outside the
+ airframe. The vent must be placed in a region of linear
+ airflow, smooth and not in an area of increasing or decreasing
+ pressure.
+
+
+ The barometric sensor in the altimeter is quite sensitive to
+ chemical damage from the products of APCP or BP combustion, so
+ make sure the ebay is carefully sealed from any compartment
+ which contains ejection charges or motors.
+
+
+
+ Ground Testing
+
+ The most important aspect of any installation is careful
+ ground testing. Bringing an airframe up to the LCO table which
+ hasn't been ground tested can lead to delays or ejection
+ charges firing on the pad, or, even worse, a recovery system
+ failure.
+
+
+ Do a 'full systems' test that includes wiring up all igniters
+ without any BP and turning on all of the electronics in flight
+ mode. This will catch any mistakes in wiring and any residual
+ RFI issues that might accidentally fire igniters at the wrong
+ time. Let the airframe sit for several minutes, checking for
+ adequate telemetry signal strength and GPS lock.
+
+
+ Ground test the ejection charges. Prepare the rocket for
+ flight, loading ejection charges and igniters. Completely
+ assemble the airframe and then use the 'Fire Igniters'
+ interface through a TeleDongle to command each charge to
+ fire. Make sure the charge is sufficient to robustly separate
+ the airframe and deploy the recovery system.
+
+
+
Hardware Specifications
@@ -2131,6 +2345,7 @@ NAR #88757, TRA #12200
Release Notes
+