flash/nor/at91samd: Use 32-bit register writes for ST-Link compat

[fw/openocd] / tcl / target / stm32l.cfg

diff --git a/tcl/target/stm32l.cfg b/tcl/target/stm32l.cfg
deleted file mode 100644 (file)
index 5c3d368..0000000
--- a/tcl/target/stm32l.cfg
+++ /dev/null
@@ -1,81 +0,0 @@
-# script for stm32l
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME stm32l
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-# Work-area is a space in RAM used for flash programming
-# By default use 14kB
-if { [info exists WORKAREASIZE] } {
-   set  _WORKAREASIZE $WORKAREASIZE
-} else {
-   set  _WORKAREASIZE 0x3800
-}
-
-# JTAG speed should be <= F_CPU/6.
-# F_CPU after reset is 2MHz, so use F_JTAG max = 333kHz
-adapter_khz 100
-
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # See STM Document RM0038
-  # Section 24.6.3
-   set _CPUTAPID 0x4ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
-   # FIXME this never gets used to override defaults...
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0038
-  # Section 24.6.2
-  set _BSTAPID 0x06416041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-
-# flash size will be probed
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32lx 0x08000000 0 0 0 $_TARGETNAME
-
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m3 reset_config sysresetreq
-
-proc stm32l_enable_HSI {} {
-       # Enable HSI as clock source
-       echo "STM32L: Enabling HSI"
-       
-       # Set HSION in RCC_CR
-       mww 0x40023800 0x00000101
-       
-       # Set HSI as SYSCLK
-       mww 0x40023808 0x00000001
-       
-       # Increase JTAG speed
-       adapter_khz 2000
-}
-
-$_TARGETNAME configure -event reset-init {
-       stm32l_enable_HSI
-}
-