cfg: remove incorrect execute permissions

[fw/openocd] / tcl / target / stm32l.cfg

diff --git a/tcl/target/stm32l.cfg b/tcl/target/stm32l.cfg
index f9f7425b9a7bb9925a21b9921710e908220b176e..1fa06f0f4698fe3d26c80564ee76926309b75c0a 100644 (file)
--- a/tcl/target/stm32l.cfg
+++ b/tcl/target/stm32l.cfg
@@ -27,10 +27,10 @@ if { [info exists WORKAREASIZE] } {
 
 # JTAG speed should be <= F_CPU/6.
 # F_CPU after reset is 2MHz, so use F_JTAG max = 333kHz
-adapter_khz 100
+adapter_khz 300
 
 adapter_nsrst_delay 100
-if {$using_jtag} {
+if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
@@ -38,12 +38,17 @@ if {$using_jtag} {
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0038
-  # Section 24.6.3
-   set _CPUTAPID 0x4ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0038
+      # Section 24.6.3
+      set _CPUTAPID 0x4ba00477
+   } {
+      set _CPUTAPID1 0x2ba01477
+      set _CPUTAPID2 0x0bc11477
+   }
 }
 
-swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID1 -expected-id $_CPUTAPID2
 
 if { [info exists BSTAPID] } {
    # FIXME this never gets used to override defaults...
@@ -54,8 +59,8 @@ if { [info exists BSTAPID] } {
   set _BSTAPID 0x06416041
 }
 
-if {$using_jtag} {
- jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
+if {[using_jtag]} {
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
@@ -67,9 +72,11 @@ $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32lx 0x08000000 0 0 0 $_TARGETNAME
 
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m reset_config sysresetreq
+if {![using_hla]} {
+   # if srst is not fitted use SYSRESETREQ to
+   # perform a soft reset
+   cortex_m reset_config sysresetreq
+}
 
 proc stm32l_enable_HSI {} {
        # Enable HSI as clock source
@@ -89,3 +96,6 @@ $_TARGETNAME configure -event reset-init {
        stm32l_enable_HSI
 }
 
+$_TARGETNAME configure -event reset-start {
+       adapter_khz 300
+}