tcl/interface: replace last deprecated commands

[fw/openocd] / tcl / target / stm32f7x.cfg

diff --git a/tcl/target/stm32f7x.cfg b/tcl/target/stm32f7x.cfg
old mode 100755 (executable)
new mode 100644 (file)
index ba1d12f..3782b9a
--- a/tcl/target/stm32f7x.cfg
+++ b/tcl/target/stm32f7x.cfg
@@ -1,3 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 # script for stm32f7x family
 
 #
@@ -12,7 +14,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f7x
 }
 
-   set _ENDIAN little
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 128kB
@@ -64,10 +66,16 @@ flash bank $_CHIPNAME.otp stm32f2x 0x1ff0f000 0 0 0 $_TARGETNAME
 #     the Flash via ITCM alias as virtual
 flash bank $_CHIPNAME.itcm-flash.alias virtual 0x00200000 0 0 0 $_TARGETNAME $_FLASHNAME
 
+if { [info exists QUADSPI] && $QUADSPI } {
+   set a [llength [flash list]]
+   set _QSPINAME $_CHIPNAME.qspi
+   flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+}
+
 # adapter speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
-adapter_khz 2000
+adapter speed 2000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -76,7 +84,7 @@ if {[using_jtag]} {
 #
 # This target is compatible with connect_assert_srst, which may be set in a
 # board file.
-reset_config srst_only srst_nogate
+reset_config srst_nogate
 
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
@@ -101,13 +109,20 @@ $_TARGETNAME configure -event examine-end {
        mmw 0xE0042008 0x00001800 0
 }
 
-$_TARGETNAME configure -event trace-config {
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
+
+lappend _telnet_autocomplete_skip _proc_pre_enable_$_CHIPNAME.tpiu
+proc _proc_pre_enable_$_CHIPNAME.tpiu {_targetname} {
+       targets $_targetname
+
        # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
        # change this value accordingly to configure trace pins
        # assignment
        mmw 0xE0042004 0x00000020 0
 }
 
+$_CHIPNAME.tpiu configure -event pre-enable "_proc_pre_enable_$_CHIPNAME.tpiu $_TARGETNAME"
+
 $_TARGETNAME configure -event reset-init {
        # If the HSE was previously enabled and the external clock source
        # disappeared, RCC_CR.HSERDY can get stuck at 1 and the PLL cannot be
@@ -162,12 +177,11 @@ $_TARGETNAME configure -event reset-init {
        if {[using_jtag]} {
                [[target current] cget -dap] memaccess 16
        } {
-               adapter_khz 8000
+               adapter speed 8000
        }
 }
 
 $_TARGETNAME configure -event reset-start {
        # Reduce speed since CPU speed will slow down to 16MHz with the reset
-       adapter_khz 2000
+       adapter speed 2000
 }
-