tcl: am437x: define registers to be used later

[fw/openocd] / tcl / target / stm32f1x.cfg

diff --git a/tcl/target/stm32f1x.cfg b/tcl/target/stm32f1x.cfg
index c89a5b55e27f05f924cdc7b67c73ccf07d52b01a..bd02e95b06057953cf4ba54f7ef46ba105f82a58 100644 (file)
--- a/tcl/target/stm32f1x.cfg
+++ b/tcl/target/stm32f1x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +12,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f1x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 4kB (as found on some STM32F100s)
@@ -29,9 +26,13 @@ if { [info exists WORKAREASIZE] } {
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0008
-  # Section 26.6.3
-   set _CPUTAPID 0x3ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0008 Section 26.6.3
+      set _CPUTAPID 0x3ba00477
+   } {
+      # this is the SW-DP tap id not the jtag tap id
+      set _CPUTAPID 0x1ba01477
+   }
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
@@ -62,7 +63,7 @@ if { [info exists BSTAPID] } {
 }
 
 if {[using_jtag]} {
- jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
        -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
        -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 \
        -expected-id $_BSTAPID6 -expected-id $_BSTAPID7 \
@@ -86,6 +87,23 @@ if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m reset_config sysresetreq
+reset_config srst_nogate
+
+if {![using_hla]} {
+    # if srst is not fitted use SYSRESETREQ to
+    # perform a soft reset
+    cortex_m reset_config sysresetreq
+}
+
+$_TARGETNAME configure -event examine-end {
+       # DBGMCU_CR |= DBG_WWDG_STOP | DBG_IWDG_STOP |
+       #              DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000307 0
+}
+
+$_TARGETNAME configure -event trace-config {
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}