flash/nor/at91samd: Use 32-bit register writes for ST-Link compat

[fw/openocd] / tcl / target / stm32f1x.cfg

diff --git a/tcl/target/stm32f1x.cfg b/tcl/target/stm32f1x.cfg
index 5a4c2fa702c760949cf07348692f4c20be1e3c52..53e81a59f6b479cb503e7b73ba32bfbe9c685313 100644 (file)
--- a/tcl/target/stm32f1x.cfg
+++ b/tcl/target/stm32f1x.cfg
@@ -1,3 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 # script for stm32f1x family
 
 #
@@ -22,6 +24,14 @@ if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE 0x1000
 }
 
+# Allow overriding the Flash bank size
+if { [info exists FLASH_SIZE] } {
+    set _FLASH_SIZE $FLASH_SIZE
+} else {
+    # autodetect size
+    set _FLASH_SIZE 0
+}
+
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
@@ -36,24 +46,25 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
    jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 # flash size will be probed
 set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME
 
 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-adapter_khz 1000
+adapter speed 1000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -72,9 +83,16 @@ $_TARGETNAME configure -event examine-end {
        mmw 0xE0042004 0x00000307 0
 }
 
-$_TARGETNAME configure -event trace-config {
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
+
+lappend _telnet_autocomplete_skip _proc_pre_enable_$_CHIPNAME.tpiu
+proc _proc_pre_enable_$_CHIPNAME.tpiu {_targetname} {
+       targets $_targetname
+
        # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
        # change this value accordingly to configure trace pins
        # assignment
        mmw 0xE0042004 0x00000020 0
 }
+
+$_CHIPNAME.tpiu configure -event pre-enable "_proc_pre_enable_$_CHIPNAME.tpiu $_TARGETNAME"