tcl/target: add SPDX tag

[fw/openocd] / tcl / target / stm32f1x.cfg

diff --git a/tcl/target/stm32f1x.cfg b/tcl/target/stm32f1x.cfg
index 31c2c5efdf65b850c8d1b6753624d03a52a55adf..4c4ff25f2b8068f9f133c62993880099de163fd9 100644 (file)
--- a/tcl/target/stm32f1x.cfg
+++ b/tcl/target/stm32f1x.cfg
@@ -1,9 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 # script for stm32f1x family
 
 #
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +14,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f1x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 4kB (as found on some STM32F100s)
@@ -25,6 +24,14 @@ if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE 0x1000
 }
 
+# Allow overriding the Flash bank size
+if { [info exists FLASH_SIZE] } {
+    set _FLASH_SIZE $FLASH_SIZE
+} else {
+    # autodetect size
+    set _FLASH_SIZE 0
+}
+
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
@@ -39,59 +46,46 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   # FIXME this never gets used to override defaults...
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0008
-  # Section 29.6.2
-  # Low density devices, Rev A
-  set _BSTAPID1 0x06412041
-  # Medium density devices, Rev A
-  set _BSTAPID2 0x06410041
-  # Medium density devices, Rev B and Rev Z
-  set _BSTAPID3 0x16410041
-  set _BSTAPID4 0x06420041
-  # High density devices, Rev A
-  set _BSTAPID5 0x06414041
-  # Connectivity line devices, Rev A and Rev Z
-  set _BSTAPID6 0x06418041
-  # XL line devices, Rev A
-  set _BSTAPID7 0x06430041
-  # VL line devices, Rev A and Z In medium-density and high-density value line devices
-  set _BSTAPID8 0x06420041
-  # VL line devices, Rev A
-  set _BSTAPID9 0x06428041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-       -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-       -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 \
-       -expected-id $_BSTAPID6 -expected-id $_BSTAPID7 \
-       -expected-id $_BSTAPID8 -expected-id $_BSTAPID9
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 # flash size will be probed
 set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME
 
 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-adapter_khz 1000
+adapter speed 1000
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
+reset_config srst_nogate
+
 if {![using_hla]} {
     # if srst is not fitted use SYSRESETREQ to
     # perform a soft reset
     cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+       # DBGMCU_CR |= DBG_WWDG_STOP | DBG_IWDG_STOP |
+       #              DBG_STANDBY | DBG_STOP | DBG_SLEEP
+       mmw 0xE0042004 0x00000307 0
+}
+
+$_TARGETNAME configure -event trace-config {
+       # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+       # change this value accordingly to configure trace pins
+       # assignment
+       mmw 0xE0042004 0x00000020 0
+}