cfg: add omapl138 support and da850evm preliminary support

[fw/openocd] / tcl / target / lpc2478.cfg

diff --git a/tcl/target/lpc2478.cfg b/tcl/target/lpc2478.cfg
index 2c8fdce33b717baca87ae8d9c1757e9624327ef9..df46c10246630f329941c6128fcedc5f1362901e 100644 (file)
--- a/tcl/target/lpc2478.cfg
+++ b/tcl/target/lpc2478.cfg
@@ -6,12 +6,6 @@ if { [info exists CHIPNAME] } {
        set  _CHIPNAME lpc2478
 }
 
-if { [info exists ENDIAN] } {
-       set  _ENDIAN $ENDIAN
-} else {
-       set  _ENDIAN little
-}
-
 if { [info exists CPUTAPID ] } {
        set _CPUTAPID $CPUTAPID
 } else {
@@ -19,7 +13,7 @@ if { [info exists CPUTAPID ] } {
 }
 
 #delays on reset lines
-jtag_nsrst_delay 100
+adapter_nsrst_delay 100
 jtag_ntrst_delay 100
 
 # LPC2000 -> SRST causes TRST
@@ -28,22 +22,23 @@ reset_config trst_and_srst srst_pulls_trst
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
+target create $_TARGETNAME arm7tdmi -chain-position $_TARGETNAME
 
 # LPC2478 has 64kB of SRAM on its main system bus (so-called Local On-Chip SRAM)
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x10000 -work-area-backup 0
 
 $_TARGETNAME configure -event reset-init {
        # Force target into ARM state
-       soft_reset_halt
+       arm core_state arm
        # Do not remap 0x0000-0x0020 to anything but the Flash
        mwb 0xE01FC040 0x01
 }
 
 # LPC2378 has 512kB of FLASH, but upper 8kB are occupied by bootloader.
 # After reset the chip uses its internal 4MHz RC oscillator.
-# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
-flash bank lpc2000 0x0 0x7D000 0 0 0 lpc2000_v2 12000 calc_checksum
+# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME lpc2000 0x0 0x7D000 0 0 $_TARGETNAME lpc2000_v2 4000 calc_checksum
 
 # Try to use RCLK, if RCLK is not available use "normal" mode. 4MHz / 6 = 666kHz, so use 500.
 jtag_rclk 500