mww [expr [dict get $soc sysbase] + 4 * $reg] $value
}
-# mrw: "memory read word", returns value of $reg
-proc mrw {reg} {
- set value ""
- ocd_mem2array value 32 $reg 1
- return $value(0)
-}
-
-# mmw: "memory modify word", updates value of $reg
-# $reg <== ((value & ~$clearbits) | $setbits)
-proc mmw {reg setbits clearbits} {
- set old [mrw $reg]
- set new [expr ($old & ~$clearbits) | $setbits]
- mww $reg $new
-}
+source [find mem_helper.tcl]
#
# pll_setup: initialize PLL
mww $pll_ctrl_addr $pll_ctrl
}
+# PLL version 0x03: tested on dm365
+proc pll_v03_setup {pll_addr mult config} {
+ set pll_ctrl_addr [expr $pll_addr + 0x100]
+ set pll_secctrl_addr [expr $pll_addr + 0x108]
+ set pll_ctrl [mrw $pll_ctrl_addr]
+
+ # 1 - power up the PLL
+ set pll_ctrl [expr $pll_ctrl & ~0x0002]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 2 - clear PLLENSRC (bit 5)
+ set pll_ctrl [expr $pll_ctrl & ~0x0020]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 2 - clear PLLEN (bit 0) ... enter bypass mode
+ set pll_ctrl [expr $pll_ctrl & ~0x0001]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 3 - wait at least 4 refclk cycles
+ sleep 1
+
+ # 4 - set PLLRST (bit 3)
+ set pll_ctrl [expr $pll_ctrl | 0x0008]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 5 - wait at least 5 usec
+ sleep 1
+
+ # 6 - clear PLLRST (bit 3)
+ set pll_ctrl [expr $pll_ctrl & ~0x0008]
+ mww $pll_ctrl_addr $pll_ctrl
+
+ # 9 - optional: write prediv, postdiv, and pllm
+ mww [expr $pll_addr + 0x0110] [expr ($mult / 2) & 0x1ff]
+ if { [dict exists $config prediv] } {
+ set div [dict get $config prediv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0114] $div
+ }
+ if { [dict exists $config postdiv] } {
+ set div [dict get $config postdiv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0128] $div
+ }
+
+ # 10 - write start sequence to PLLSECCTL
+ mww $pll_secctrl_addr 0x00470000
+ mww $pll_secctrl_addr 0x00460000
+ mww $pll_secctrl_addr 0x00400000
+ mww $pll_secctrl_addr 0x00410000
+
+ # 11 - optional: set plldiv1, plldiv2, ...
+ # NOTE: this assumes some registers have their just-reset values:
+ # - PLLSTAT.GOSTAT is clear when we enter
+ set aln 0
+ if { [dict exists $config div1] } {
+ set div [dict get $config div1]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0118] $div
+ set aln [expr $aln | 0x1]
+ } else {
+ mww [expr $pll_addr + 0x0118] 0
+ }
+ if { [dict exists $config div2] } {
+ set div [dict get $config div2]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x011c] $div
+ set aln [expr $aln | 0x2]
+ } else {
+ mww [expr $pll_addr + 0x011c] 0
+ }
+ if { [dict exists $config div3] } {
+ set div [dict get $config div3]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0120] $div
+ set aln [expr $aln | 0x4]
+ } else {
+ mww [expr $pll_addr + 0x0120] 0
+ }
+ if { [dict exists $config oscdiv] } {
+ set div [dict get $config oscdiv]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0124] $div
+ } else {
+ mww [expr $pll_addr + 0x0124] 0
+ }
+ if { [dict exists $config div4] } {
+ set div [dict get $config div4]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0160] $div
+ set aln [expr $aln | 0x8]
+ } else {
+ mww [expr $pll_addr + 0x0160] 0
+ }
+ if { [dict exists $config div5] } {
+ set div [dict get $config div5]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0164] $div
+ set aln [expr $aln | 0x10]
+ } else {
+ mww [expr $pll_addr + 0x0164] 0
+ }
+ if { [dict exists $config div6] } {
+ set div [dict get $config div6]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0168] $div
+ set aln [expr $aln | 0x20]
+ } else {
+ mww [expr $pll_addr + 0x0168] 0
+ }
+ if { [dict exists $config div7] } {
+ set div [dict get $config div7]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x016c] $div
+ set aln [expr $aln | 0x40]
+ } else {
+ mww [expr $pll_addr + 0x016c] 0
+ }
+ if { [dict exists $config div8] } {
+ set div [dict get $config div8]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0170] $div
+ set aln [expr $aln | 0x80]
+ } else {
+ mww [expr $pll_addr + 0x0170] 0
+ }
+ if { [dict exists $config div9] } {
+ set div [dict get $config div9]
+ set div [expr 0x8000 | ($div - 1)]
+ mww [expr $pll_addr + 0x0174] $div
+ set aln [expr $aln | 0x100]
+ } else {
+ mww [expr $pll_addr + 0x0174] 0
+ }
+ if {$aln != 0} {
+ # clear pllcmd.GO
+ mww [expr $pll_addr + 0x0138] 0x00
+ # write alingment flags
+ mww [expr $pll_addr + 0x0140] $aln
+ # write pllcmd.GO; poll pllstat.GO
+ mww [expr $pll_addr + 0x0138] 0x01
+ set pllstat [expr $pll_addr + 0x013c]
+ while {[expr [mrw $pllstat] & 0x01] != 0} { sleep 1 }
+ }
+ mww [expr $pll_addr + 0x0138] 0x00
+ set addr [dict get $config ctladdr]
+ while {[expr [mrw $addr] & 0x0e000000] != 0x0e000000} { sleep 1 }
+
+ # 12 - set PLLEN (bit 0) ... leave bypass mode
+ set pll_ctrl [expr $pll_ctrl | 0x0001]
+ mww $pll_ctrl_addr $pll_ctrl
+}
+
# NOTE: dm6446 requires EMURSTIE set in MDCTL before certain
# modules can be enabled.
projects / fw / openocd / blobdiff