#-------------------------------------------------------------------------
# Mini2440 Samsung s3c2440A Processor with 64MB DRAM, 64MB NAND, 2 MB N0R
# NOTE: Configured for NAND boot (switch S2 in NANDBOOT)
-# 64 MB NAND (Samsung K9D1208V0M)
+# 64 MB NAND (Samsung K9D1208V0M)
# B Findlay 08/09
#
# ----------- Important notes to help you on your way ----------
# NOR/NAND Boot Switch - I have not read the vivi source, but from
# what I could tell from reading the registers it appears that vivi
# loads itself into DRAM and then flips NFCONT (0x4E000004) bits
-# Mode (bit 0 = 1), and REG_nCE (bit 1 = 0) which maps the NAND
-# FLASH at the bottom 64MB of memory. This essentially takes the
-# NOR Flash out of the circuit so you can't trash it.
+# Mode (bit 0 = 1), and REG_nCE (bit 1 = 0) which maps the NAND
+# FLASH at the bottom 64MB of memory. This essentially takes the
+# NOR Flash out of the circuit so you can't trash it.
#
# I adapted the samsung_s3c2440.cfg file which is why I did not
# include "source [find target/samsung_s3c2440.cfg]". I believe
# JTAG ADAPTER SPECIFIC
# IMPORTANT! Any JTAG device that uses ADAPTIVE CLOCKING will likely
# FAIL as the pin RTCK on the mini2440 10 pin JTAG Conn doesn't exist.
-# This is Pin 11 (RTCK) on 20 pin JTAG connector. Therefore it is
+# This is Pin 11 (RTCK) on 20 pin JTAG connector. Therefore it is
# necessary to FORCE setting the clock. Normally this should be configured
-# in the openocd.cfg file, but was placed here as it can be a tough
+# in the openocd.cfg file, but was placed here as it can be a tough
# problem to figure out. THIS MAY NOT FIX YOUR PROBLEM.. I modified
# the openOCD driver jlink.c and posted it here. It may eventually end
# up changed in openOCD, but its a hack in the driver and really should
# But it should get you way ahead of the game from where I started.
# If you find problems (and fixes) please post them to
# openocd-development@lists.berlios.de and join the developers and
-# check in fixes to this and anything else you find. I do not
-# provide support, but if you ask really nice and I see anything
+# check in fixes to this and anything else you find. I do not
+# provide support, but if you ask really nice and I see anything
# obvious I will tell you.. mostly just dig, fix, and submit to openocd.
-#
+#
# best! brfindla@yahoo.com Nashua, NH USA
#
# Recommended resources:
# - first two are the best Mini2440 resources anywhere
# - maintained by buserror... thanks guy!
#
-# http://bliterness.blogspot.com/
+# http://bliterness.blogspot.com/
# http://code.google.com/p/mini2440/
#
# others....
-#
+#
# http://forum.sparkfun.com/viewforum.php?f=18
# http://labs.kernelconcepts.de/Publications/Micro24401/
# http://www.friendlyarm.net/home
# Target configuration for the Samsung 2440 system on chip
# Tested on a S3C2440 Evaluation board by keesj
# Processor : ARM920Tid(wb) rev 0 (v4l)
-# Info: JTAG tap: s3c2440.cpu tap/device found: 0x0032409d
+# Info: JTAG tap: s3c2440.cpu tap/device found: 0x0032409d
# (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0)
#-------------------------------------------------------------------------
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
set _CHIPNAME s3c2440
}
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
# this defaults to a bigendian
set _ENDIAN little
}
#reset configuration
jtag_nsrst_delay 100
-jtag_ntrst_delay 100
+jtag_ntrst_delay 100
reset_config trst_and_srst
#-------------------------------------------------------------------------
# JTAG ADAPTER SPECIFIC
-# IMPORTANT! See README at top of this file.
+# IMPORTANT! See README at top of this file.
#-------------------------------------------------------------------------
- jtag_khz 12000
- jtag interface
+ jtag_khz 12000
+ jtag interface
#-------------------------------------------------------------------------
# GDB Setup
gdb_port 3333
gdb_detach resume
- gdb_breakpoint_override hard
+ gdb_breakpoint_override hard
gdb_memory_map enable
- gdb_flash_program enable
+ gdb_flash_program enable
#------------------------------------------------
# ARM SPECIFIC
#------------------------------------------------
- targets
+ targets
# arm7_9 dcc_downloads enable
# arm7_9 fast_memory_access enable
-
-
- nand device s3c2440 0
+
+
+ nand device s3c2440 0
jtag_nsrst_delay 100
- jtag_ntrst_delay 100
+ jtag_ntrst_delay 100
reset_config trst_and_srst
init
# OM2 OM3 pulled to ground so main clock and
# usb clock are off 12mHz xtal
#-----------------------------------------------
-
+
arm920t mww_phys 0x4C000014 0x00000005 # Clock Divider control Reg
arm920t mww_phys 0x4C000000 0xFFFFFFFF # LOCKTIME count register
arm920t mww_phys 0x4C000008 0x00038022 # UPPLCON USB clock config Reg
arm920t mww_phys 0x4C000004 0x0007F021 # MPPLCON Proc clock config Reg
-
+
#-----------------------------------------------
# Configure Memory controller
# BWSCON configures all banks, NAND, NOR, DRAM
# DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
#-----------------------------------------------
-
+
arm920t mww_phys 0x48000000 0x22111112 # BWSCON - Bank and Bus Width
arm920t mww_phys 0x48000010 0x00001112 # BANKCON4 - ?
- arm920t mww_phys 0x4800001c 0x00018009 # BANKCON6 - DRAM
- arm920t mww_phys 0x48000020 0x00018009 # BANKCON7 - DRAM
- arm920t mww_phys 0x48000024 0x008E04EB # REFRESH - DRAM
- arm920t mww_phys 0x48000028 0x000000B2 # BANKSIZE - DRAM
- arm920t mww_phys 0x4800002C 0x00000030 # MRSRB6 - DRAM
- arm920t mww_phys 0x48000030 0x00000030 # MRSRB7 - DRAM
-
+ arm920t mww_phys 0x4800001c 0x00018009 # BANKCON6 - DRAM
+ arm920t mww_phys 0x48000020 0x00018009 # BANKCON7 - DRAM
+ arm920t mww_phys 0x48000024 0x008E04EB # REFRESH - DRAM
+ arm920t mww_phys 0x48000028 0x000000B2 # BANKSIZE - DRAM
+ arm920t mww_phys 0x4800002C 0x00000030 # MRSRB6 - DRAM
+ arm920t mww_phys 0x48000030 0x00000030 # MRSRB7 - DRAM
+
#-----------------------------------------------
# Now port configuration for enables for memory
# and other stuff.
#-----------------------------------------------
-
+
arm920t mww_phys 0x56000000 0x007FFFFF # GPACON
-
- arm920t mww_phys 0x56000010 0x00295559 # GPBCON
+
+ arm920t mww_phys 0x56000010 0x00295559 # GPBCON
arm920t mww_phys 0x56000018 0x000003FF # GPBUP (PULLUP ENABLE)
- arm920t mww_phys 0x56000014 0x000007C2 # GPBDAT
-
- arm920t mww_phys 0x56000020 0xAAAAA6AA # GPCCON
+ arm920t mww_phys 0x56000014 0x000007C2 # GPBDAT
+
+ arm920t mww_phys 0x56000020 0xAAAAA6AA # GPCCON
arm920t mww_phys 0x56000028 0x0000FFFF # GPCUP
- arm920t mww_phys 0x56000024 0x00000020 # GPCDAT
-
- arm920t mww_phys 0x56000030 0xAAAAAAAA # GPDCON
- arm920t mww_phys 0x56000038 0x0000FFFF # GPDUP
-
- arm920t mww_phys 0x56000040 0xAAAAAAAA # GPECON
- arm920t mww_phys 0x56000048 0x0000FFFF # GPEUP
-
- arm920t mww_phys 0x56000050 0x00001555 # GPFCON
- arm920t mww_phys 0x56000058 0x0000007F # GPFUP
- arm920t mww_phys 0x56000054 0x00000000 # GPFDAT
-
- arm920t mww_phys 0x56000060 0x00150114 # GPGCON
- arm920t mww_phys 0x56000068 0x0000007F # GPGUP
-
- arm920t mww_phys 0x56000070 0x0015AAAA # GPHCON
- arm920t mww_phys 0x56000078 0x000003FF # GPGUP
-
-}
+ arm920t mww_phys 0x56000024 0x00000020 # GPCDAT
+
+ arm920t mww_phys 0x56000030 0xAAAAAAAA # GPDCON
+ arm920t mww_phys 0x56000038 0x0000FFFF # GPDUP
+
+ arm920t mww_phys 0x56000040 0xAAAAAAAA # GPECON
+ arm920t mww_phys 0x56000048 0x0000FFFF # GPEUP
+
+ arm920t mww_phys 0x56000050 0x00001555 # GPFCON
+ arm920t mww_phys 0x56000058 0x0000007F # GPFUP
+ arm920t mww_phys 0x56000054 0x00000000 # GPFDAT
+
+ arm920t mww_phys 0x56000060 0x00150114 # GPGCON
+ arm920t mww_phys 0x56000068 0x0000007F # GPGUP
+
+ arm920t mww_phys 0x56000070 0x0015AAAA # GPHCON
+ arm920t mww_phys 0x56000078 0x000003FF # GPGUP
+
+}
#-----------------------------------------
halt
-
+
#flash configuration (K9D1208V0M: 512Mbit, x8, 3.3V, Mode: Normal, 1st gen)
nand probe 0
nand list
echo "---- http://repo.or.cz/w/u-boot-openmoko/mini2440.git ---"
echo "---- Also this: ---"
echo "---- http://code.google.com/p/mini2440/wiki/MiniBringup --"
- echo "----------------------------------------------------------"
-
+ echo "----------------------------------------------------------"
+
init_2440
echo "Loading /tftpboot/u-boot-nand512.bin"
load_image /tftpboot/u-boot-nand512.bin 0x33f80000 bin
projects / fw / openocd / blobdiff