imx31pdk: use rclk w/1MHz fallback

[fw/openocd] / tcl / board / mini2440.cfg

diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index 29819501ffffde6febdd57e340729665f86bc250..168896540f9c49a0f315e313d9a381d1de5a0475 100644 (file)
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -71,6 +71,11 @@
 #
 #
 #
+
+# FIXME use some standard target config, maybe create one from this
+#
+#      source [find target/...cfg]
+
 #-------------------------------------------------------------------------
 # Target configuration for the Samsung 2440 system on chip
 # Tested on a S3C2440 Evaluation board by keesj
@@ -102,12 +107,12 @@ if { [info exists CPUTAPID ] } {
 #jtag scan chain
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm920t
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME
+$_TARGETNAME configure -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1
 
 #reset configuration
-jtag_nsrst_delay 100
+adapter_nsrst_delay 100
 jtag_ntrst_delay 100
 reset_config trst_and_srst
 
@@ -116,7 +121,7 @@ reset_config trst_and_srst
 # IMPORTANT! See README at top of this file.
 #-------------------------------------------------------------------------
 
-    jtag_khz 12000
+    adapter_khz 12000
     jtag interface
 
 #-------------------------------------------------------------------------
@@ -136,7 +141,7 @@ reset_config trst_and_srst
 
     nand device s3c2440 0
 
-    jtag_nsrst_delay 100
+    adapter_nsrst_delay 100
     jtag_ntrst_delay 100
     reset_config trst_and_srst
     init
@@ -177,10 +182,10 @@ proc init_2440 { } {
     # usb clock are off 12mHz xtal
     #-----------------------------------------------
 
-    arm920t mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
-    arm920t mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
-    arm920t mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
-    arm920t mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
+    mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
+    mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
+    mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
+    mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg
 
     #-----------------------------------------------
     # Configure Memory controller
@@ -188,45 +193,45 @@ proc init_2440 { } {
     # DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
     #-----------------------------------------------
 
-    arm920t mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
-    arm920t mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
-    arm920t mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
-    arm920t mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
-    arm920t mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
-    arm920t mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
-    arm920t mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
-    arm920t mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
+    mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
+    mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
+    mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
+    mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
+    mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
+    mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
+    mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
+    mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM
 
     #-----------------------------------------------
     # Now port configuration for enables for memory
     # and other stuff.
     #-----------------------------------------------
 
-    arm920t mww phys 0x56000000        0x007FFFFF #  GPACON
+    mww phys 0x56000000        0x007FFFFF #  GPACON
 
-    arm920t mww phys 0x56000010        0x00295559 #  GPBCON
-    arm920t mww phys 0x56000018        0x000003FF #  GPBUP (PULLUP ENABLE)
-    arm920t mww phys 0x56000014        0x000007C2 #  GPBDAT
+    mww phys 0x56000010        0x00295559 #  GPBCON
+    mww phys 0x56000018        0x000003FF #  GPBUP (PULLUP ENABLE)
+    mww phys 0x56000014        0x000007C2 #  GPBDAT
 
-    arm920t mww phys 0x56000020        0xAAAAA6AA #  GPCCON
-    arm920t mww phys 0x56000028        0x0000FFFF #  GPCUP
-    arm920t mww phys 0x56000024        0x00000020 #  GPCDAT
+    mww phys 0x56000020        0xAAAAA6AA #  GPCCON
+    mww phys 0x56000028        0x0000FFFF #  GPCUP
+    mww phys 0x56000024        0x00000020 #  GPCDAT
 
-    arm920t mww phys 0x56000030        0xAAAAAAAA #  GPDCON
-    arm920t mww phys 0x56000038        0x0000FFFF #  GPDUP
+    mww phys 0x56000030        0xAAAAAAAA #  GPDCON
+    mww phys 0x56000038        0x0000FFFF #  GPDUP
 
-    arm920t mww phys 0x56000040        0xAAAAAAAA #  GPECON
-    arm920t mww phys 0x56000048        0x0000FFFF #  GPEUP
+    mww phys 0x56000040        0xAAAAAAAA #  GPECON
+    mww phys 0x56000048        0x0000FFFF #  GPEUP
 
-    arm920t mww phys 0x56000050        0x00001555 #  GPFCON
-    arm920t mww phys 0x56000058        0x0000007F #  GPFUP
-    arm920t mww phys 0x56000054        0x00000000 #  GPFDAT
+    mww phys 0x56000050        0x00001555 #  GPFCON
+    mww phys 0x56000058        0x0000007F #  GPFUP
+    mww phys 0x56000054        0x00000000 #  GPFDAT
 
-    arm920t mww phys 0x56000060        0x00150114 #  GPGCON
-    arm920t mww phys 0x56000068        0x0000007F #  GPGUP
+    mww phys 0x56000060        0x00150114 #  GPGCON
+    mww phys 0x56000068        0x0000007F #  GPGUP
 
-    arm920t mww phys 0x56000070        0x0015AAAA #  GPHCON
-    arm920t mww phys 0x56000078        0x000003FF #  GPGUP
+    mww phys 0x56000070        0x0015AAAA #  GPHCON
+    mww phys 0x56000078        0x000003FF #  GPGUP
 
 }
 
@@ -292,7 +297,7 @@ proc load_uboot { } {
 proc s {} {
         step
         reg
-        armv4_5 disassemble 0x33F80068 0x10
+        arm disassemble 0x33F80068 0x10
 }
 
 proc help_2440 {} {