add Freescale Kinetis K40 devices and Kwikstik eval board

[fw/openocd] / tcl / board / hitex_str9-comstick.cfg

diff --git a/tcl/board/hitex_str9-comstick.cfg b/tcl/board/hitex_str9-comstick.cfg
index de4d56ddf576b79081d13e57c13533e94fd7a53a..c85681b186ea4e4425f98241355dc59bcf29e17b 100644 (file)
--- a/tcl/board/hitex_str9-comstick.cfg
+++ b/tcl/board/hitex_str9-comstick.cfg
@@ -5,24 +5,29 @@
 source [find interface/hitex_str9-comstick.cfg]
 
 # set jtag speed
-jtag_khz 3000
+adapter_khz 3000
 
-jtag_nsrst_delay 100
+adapter_nsrst_delay 100
 jtag_ntrst_delay 100
 #use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config trst_and_srst
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
 
-if { [info exists CHIPNAME] } {        
-   set  _CHIPNAME $CHIPNAME    
-} else {        
+#
+# FIXME use the standard str912 target config; that script might need
+# updating to "-ignore-version" for the boundary scan TAP
+#
+#      source [find target/str912.cfg]
+#
+
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
    set  _CHIPNAME str912
 }
 
-if { [info exists ENDIAN] } {  
-   set  _ENDIAN $ENDIAN    
-} else {        
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
    set  _ENDIAN little
 }
 
@@ -50,23 +55,25 @@ if { [info exists BSTAPID ] } {
 }
 jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME
 
 $_TARGETNAME configure -event reset-init {
        # We can increase speed now that we know the target is halted.
        #jtag_rclk 3000
-       
+
        # -- Enable 96K RAM
        # PFQBC enabled / DTCM & AHB wait-states disabled
-       mww 0x5C002034 0x0191 
+       mww 0x5C002034 0x0191
 
        str9x flash_config 0 4 2 0 0x80000
        flash protect 0 0 7 off
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
 
 #flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-flash bank str9x 0x00080000 0x00008000 0 0 0
+set _FLASHNAME $_CHIPNAME.flash0
+flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 0
+set _FLASHNAME $_CHIPNAME.flash1
+flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 0