Move TCL script files -- Step 2 of 2:

[fw/openocd] / tcl / board / hitex_str9-comstick.cfg

diff --git a/tcl/board/hitex_str9-comstick.cfg b/tcl/board/hitex_str9-comstick.cfg
new file mode 100644 (file)
index 0000000..de4d56d
--- /dev/null
+++ b/tcl/board/hitex_str9-comstick.cfg
@@ -0,0 +1,72 @@
+# Hitex STR9-comStick
+# http://www.hitex.com/index.php?id=383
+# This works for the STR9-comStick revisions STR912CS-A1 and STR912CS-A2.
+
+source [find interface/hitex_str9-comstick.cfg]
+
+# set jtag speed
+jtag_khz 3000
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+
+if { [info exists CHIPNAME] } {        
+   set  _CHIPNAME $CHIPNAME    
+} else {        
+   set  _CHIPNAME str912
+}
+
+if { [info exists ENDIAN] } {  
+   set  _ENDIAN $ENDIAN    
+} else {        
+   set  _ENDIAN little
+}
+
+if { [info exists FLASHTAPID ] } {
+   set _FLASHTAPID $FLASHTAPID
+} else {
+   set _FLASHTAPID 0x04570041
+}
+jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
+
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x25966041
+}
+jtag newtap $_CHIPNAME cpu   -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+if { [info exists BSTAPID ] } {
+   set _BSTAPID $BSTAPID
+} else {
+   # Found on STR9-comStick, revision STR912CS-A1
+   set _BSTAPID1 0x1457f041
+   # Found on STR9-comStick, revision STR912CS-A2
+   set _BSTAPID2 0x2457f041
+}
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+
+$_TARGETNAME configure -event reset-init {
+       # We can increase speed now that we know the target is halted.
+       #jtag_rclk 3000
+       
+       # -- Enable 96K RAM
+       # PFQBC enabled / DTCM & AHB wait-states disabled
+       mww 0x5C002034 0x0191 
+
+       str9x flash_config 0 4 2 0 0x80000
+       flash protect 0 0 7 off
+}
+
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
+
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str9x 0x00000000 0x00080000 0 0 0
+flash bank str9x 0x00080000 0x00008000 0 0 0