tcl/board: add SPDX tag

[fw/openocd] / tcl / board / digi_connectcore_wi-9c.cfg

diff --git a/tcl/board/digi_connectcore_wi-9c.cfg b/tcl/board/digi_connectcore_wi-9c.cfg
index 58f12a6870305143c5aa4be939d8027fc13e210b..0ff47428a1e5d6a4095f8fc5ac21c640836cac66 100644 (file)
--- a/tcl/board/digi_connectcore_wi-9c.cfg
+++ b/tcl/board/digi_connectcore_wi-9c.cfg
@@ -1,9 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
 ######################################
 # Target: DIGI ConnectCore Wi-9C
 ######################################
 
 reset_config trst_and_srst
 
+# FIXME use some standard target config, maybe create one from this
+#
+#      source [find target/...cfg]
+
 if { [info exists CHIPNAME] } {
    set  _CHIPNAME $CHIPNAME
 } else {
@@ -23,16 +29,16 @@ if { [info exists ENDIAN] } {
 jtag_rclk 1000
 
 
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
    set _CPUTAPID 0x07926031
 }
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+set _TARGETNAME $_CHIPNAME.cpu
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
-jtag_nsrst_delay 200
+adapter srst delay 200
 jtag_ntrst_delay 0
 
 
@@ -40,35 +46,35 @@ jtag_ntrst_delay 0
 # Target configuration
 ######################
 
-target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs
+target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME
 
 $_TARGETNAME configure -event reset-init {
        mww 0x90600104 0x33313333
-       mww 0xA0700000 0x00000001  # Enable the memory controller.
-       mww 0xA0700024 0x00000006  # Set the refresh counter 6
-       mww 0xA0700028 0x00000001  #
-       mww 0xA0700030 0x00000001  # Set the precharge period
-       mww 0xA0700034 0x00000004  # Active to precharge command period is 16 clock cycles
-       mww 0xA070003C 0x00000001  # tAPR
-       mww 0xA0700040 0x00000005  # tDAL
-       mww 0xA0700044 0x00000001  # tWR
-       mww 0xA0700048 0x00000006  # tRC 32 clock cycles
-       mww 0xA070004C 0x00000006  # tRFC 32 clock cycles
-       mww 0xA0700054 0x00000001  # tRRD
-       mww 0xA0700058 0x00000001  # tMRD
-       mww 0xA0700100 0x00004280  # Dynamic Config 0 (cs4)
-       mww 0xA0700120 0x00004280  # Dynamic Config 1 (cs5)
-       mww 0xA0700140 0x00004280  # Dynamic Config 2 (cs6)
-       mww 0xA0700160 0x00004280  # Dynamic Config 3 (cs7)
+       mww 0xA0700000 0x00000001  ;# Enable the memory controller.
+       mww 0xA0700024 0x00000006  ;# Set the refresh counter 6
+       mww 0xA0700028 0x00000001  ;#
+       mww 0xA0700030 0x00000001  ;# Set the precharge period
+       mww 0xA0700034 0x00000004  ;# Active to precharge command period is 16 clock cycles
+       mww 0xA070003C 0x00000001  ;# tAPR
+       mww 0xA0700040 0x00000005  ;# tDAL
+       mww 0xA0700044 0x00000001  ;# tWR
+       mww 0xA0700048 0x00000006  ;# tRC 32 clock cycles
+       mww 0xA070004C 0x00000006  ;# tRFC 32 clock cycles
+       mww 0xA0700054 0x00000001  ;# tRRD
+       mww 0xA0700058 0x00000001  ;# tMRD
+       mww 0xA0700100 0x00004280  ;# Dynamic Config 0 (cs4)
+       mww 0xA0700120 0x00004280  ;# Dynamic Config 1 (cs5)
+       mww 0xA0700140 0x00004280  ;# Dynamic Config 2 (cs6)
+       mww 0xA0700160 0x00004280  ;# Dynamic Config 3 (cs7)
        #
-       mww 0xA0700104 0x00000203  # CAS latency is 2 at 100 MHz
-       mww 0xA0700124 0x00000203  # CAS latency is 2 at 100 MHz
-       mww 0xA0700144 0x00000203  # CAS latency is 2 at 100 MHz
-       mww 0xA0700164 0x00000203  # CAS latency is 2 at 100 MHz
+       mww 0xA0700104 0x00000203  ;# CAS latency is 2 at 100 MHz
+       mww 0xA0700124 0x00000203  ;# CAS latency is 2 at 100 MHz
+       mww 0xA0700144 0x00000203  ;# CAS latency is 2 at 100 MHz
+       mww 0xA0700164 0x00000203  ;# CAS latency is 2 at 100 MHz
        #
-       mww 0xA0700020 0x00000103  # issue SDRAM PALL command
+       mww 0xA0700020 0x00000103  ;# issue SDRAM PALL command
        #
-       mww 0xA0700024 0x00000001  # Set the refresh counter to be as small as possible
+       mww 0xA0700024 0x00000001  ;# Set the refresh counter to be as small as possible
        #
        # Add some dummy writes to give the SDRAM time to settle, it needs two
        # AHB clock cycles, here we poke in the debugger flag, this lets
@@ -85,19 +91,19 @@ $_TARGETNAME configure -event reset-init {
        mdw 0xA0900000
        mdw 0xA0900000
        #
-       mww 0xA0700024 0x00000030 # Set the refresh counter to 30
-       mww 0xA0700020 0x00000083 # Issue SDRAM MODE command
+       mww 0xA0700024 0x00000030 ;# Set the refresh counter to 30
+       mww 0xA0700020 0x00000083 ;# Issue SDRAM MODE command
        #
        # Next we perform a read of RAM.
        # mw = move word.
        mdw 0x00022000
        # mw 0x00022000:P, r3  # 22000 for cas2 latency, 32000 for cas 3
        #
-       mww 0xA0700020 0x00000003   # issue SDRAM NORMAL command
-       mww 0xA0700100 0x00084280   # Enable buffer access
-       mww 0xA0700120 0x00084280   # Enable buffer access
-       mww 0xA0700140 0x00084280   # Enable buffer access
-       mww 0xA0700160 0x00084280   # Enable buffer access
+       mww 0xA0700020 0x00000003   ;# issue SDRAM NORMAL command
+       mww 0xA0700100 0x00084280   ;# Enable buffer access
+       mww 0xA0700120 0x00084280   ;# Enable buffer access
+       mww 0xA0700140 0x00084280   ;# Enable buffer access
+       mww 0xA0700160 0x00084280   ;# Enable buffer access
 
        #Set byte lane state (static mem 1)"
        mww 0xA0700220 0x00000082
@@ -114,12 +120,13 @@ $_TARGETNAME configure -event reset-init {
        reg cpsr 0xd3
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1
 
 #####################
 # Flash configuration
 #####################
 
 #M29DW323DB - not working
-#flash bank cfi <base> <size> <chip width> <bus width> <target#>
-flash bank cfi 0x50000000 0x0400000 2 2 0
+#flash bank <name> cfi <base> <size> <chip width> <bus width> <target>
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x50000000 0x0400000 2 2 $_TARGETNAME