#define STLINK_V2_PID (0x3748)
#define STLINK_V2_1_PID (0x374B)
#define STLINK_V2_1_NO_MSD_PID (0x3752)
+#define STLINK_V3_USBLOADER_PID (0x374D)
+#define STLINK_V3E_PID (0x374E)
+#define STLINK_V3S_PID (0x374F)
+#define STLINK_V3_2VCP_PID (0x3753)
-/* the current implementation of the stlink limits
- * 8bit read/writes to max 64 bytes. */
+/*
+ * ST-Link/V1, ST-Link/V2 and ST-Link/V2.1 are full-speed USB devices and
+ * this limits the bulk packet size and the 8bit read/writes to max 64 bytes.
+ * STLINK-V3 is a high speed USB 2.0 and the limit is 512 bytes.
+ */
#define STLINK_MAX_RW8 (64)
+#define STLINKV3_MAX_RW8 (512)
/* "WAIT" responses will be retried (with exponential backoff) at
* most this many times before failing to caller.
enum stlink_jtag_api_version {
STLINK_JTAG_API_V1 = 1,
STLINK_JTAG_API_V2,
+ STLINK_JTAG_API_V3,
};
/** */
int jtag;
/** */
int swim;
- /** highest supported jtag api version */
- enum stlink_jtag_api_version jtag_api_max;
+ /** jtag api version supported */
+ enum stlink_jtag_api_version jtag_api;
+ /** one bit for each feature supported. See macros STLINK_F_* */
+ uint32_t flags;
};
/** */
uint16_t vid;
/** */
uint16_t pid;
- /** this is the currently used jtag api */
- enum stlink_jtag_api_version jtag_api;
/** */
struct {
/** whether SWO tracing is enabled or not */
#define STLINK_SWIM_READMEM 0x0b
#define STLINK_SWIM_READBUF 0x0c
-#define STLINK_DEBUG_ENTER_JTAG 0x00
#define STLINK_DEBUG_GETSTATUS 0x01
#define STLINK_DEBUG_FORCEDEBUG 0x02
#define STLINK_DEBUG_APIV1_RESETSYS 0x03
#define STLINK_DEBUG_APIV1_WRITEDEBUGREG 0x0f
#define STLINK_DEBUG_APIV1_SETWATCHPOINT 0x10
-#define STLINK_DEBUG_ENTER_JTAG 0x00
-#define STLINK_DEBUG_ENTER_SWD 0xa3
+#define STLINK_DEBUG_ENTER_JTAG_RESET 0x00
+#define STLINK_DEBUG_ENTER_SWD_NO_RESET 0xa3
+#define STLINK_DEBUG_ENTER_JTAG_NO_RESET 0xa4
#define STLINK_DEBUG_APIV1_ENTER 0x20
#define STLINK_DEBUG_EXIT 0x21
#define STLINK_DEBUG_APIV2_GETLASTRWSTATUS 0x3B
#define STLINK_DEBUG_APIV2_DRIVE_NRST 0x3C
+#define STLINK_DEBUG_APIV2_GETLASTRWSTATUS2 0x3E
+
#define STLINK_DEBUG_APIV2_START_TRACE_RX 0x40
#define STLINK_DEBUG_APIV2_STOP_TRACE_RX 0x41
#define STLINK_DEBUG_APIV2_GET_TRACE_NB 0x42
#define STLINK_DEBUG_APIV2_SWD_SET_FREQ 0x43
#define STLINK_DEBUG_APIV2_JTAG_SET_FREQ 0x44
+#define STLINK_DEBUG_APIV2_READMEM_16BIT 0x47
+#define STLINK_DEBUG_APIV2_WRITEMEM_16BIT 0x48
+
+#define STLINK_APIV3_SET_COM_FREQ 0x61
+#define STLINK_APIV3_GET_COM_FREQ 0x62
+
+#define STLINK_APIV3_GET_VERSION_EX 0xFB
+
#define STLINK_DEBUG_APIV2_DRIVE_NRST_LOW 0x00
#define STLINK_DEBUG_APIV2_DRIVE_NRST_HIGH 0x01
#define STLINK_DEBUG_APIV2_DRIVE_NRST_PULSE 0x02
#define STLINK_TRACE_SIZE 4096
#define STLINK_TRACE_MAX_HZ 2000000
-#define STLINK_TRACE_MIN_VERSION 13
+
+#define STLINK_V3_MAX_FREQ_NB 10
/** */
enum stlink_mode {
#define REQUEST_SENSE 0x03
#define REQUEST_SENSE_LENGTH 18
+/*
+ * Map the relevant features, quirks and workaround for specific firmware
+ * version of stlink
+ */
+#define STLINK_F_HAS_TRACE (1UL << 0)
+#define STLINK_F_HAS_SWD_SET_FREQ (1UL << 1)
+#define STLINK_F_HAS_JTAG_SET_FREQ (1UL << 2)
+#define STLINK_F_HAS_MEM_16BIT (1UL << 3)
+#define STLINK_F_HAS_GETLASTRWSTATUS2 (1UL << 4)
+
+/* aliases */
+#define STLINK_F_HAS_TARGET_VOLT STLINK_F_HAS_TRACE
+
struct speed_map {
int speed;
int speed_divisor;
static void stlink_usb_init_buffer(void *handle, uint8_t direction, uint32_t size);
static int stlink_swim_status(void *handle);
+/** */
+static unsigned int stlink_usb_block(void *handle)
+{
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (h->version.stlink == 3)
+ return STLINKV3_MAX_RW8;
+ else
+ return STLINK_MAX_RW8;
+}
+
/** */
static int stlink_usb_xfer_v1_get_status(void *handle)
{
}
/* TODO: no error checking yet on api V1 */
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->databuf[0] = STLINK_DEBUG_ERR_OK;
switch (h->databuf[0]) {
assert(handle != NULL);
- assert(h->version.stlink >= 2);
+ assert(h->version.flags & STLINK_F_HAS_TRACE);
if (jtag_libusb_bulk_read(h->fd, h->trace_ep, (char *)buf,
size, STLINK_READ_TIMEOUT) != size) {
static int stlink_usb_version(void *handle)
{
int res;
- uint16_t v;
+ uint32_t flags;
+ uint16_t version;
+ uint8_t v, x, y, jtag, swim, msd, bridge = 0;
+ char v_str[5 * (1 + 3) + 1]; /* VvJjMmBbSs */
+ char *p;
struct stlink_usb_handle_s *h = handle;
assert(handle != NULL);
if (res != ERROR_OK)
return res;
- v = (h->databuf[0] << 8) | h->databuf[1];
+ version = be_to_h_u16(h->databuf);
+ v = (version >> 12) & 0x0f;
+ x = (version >> 6) & 0x3f;
+ y = version & 0x3f;
+
+ h->vid = le_to_h_u16(h->databuf + 2);
+ h->pid = le_to_h_u16(h->databuf + 4);
+
+ switch (h->pid) {
+ case STLINK_V2_1_PID:
+ case STLINK_V2_1_NO_MSD_PID:
+ if ((x <= 22 && y == 7) || (x >= 25 && y >= 7 && y <= 12)) {
+ /* MxSy : STM8 V2.1 - SWIM only */
+ msd = x;
+ swim = y;
+ jtag = 0;
+ } else {
+ /* JxMy : STM32 V2.1 - JTAG/SWD only */
+ jtag = x;
+ msd = y;
+ swim = 0;
+ }
+ break;
+ default:
+ jtag = x;
+ swim = y;
+ msd = 0;
+ break;
+ }
- h->version.stlink = (v >> 12) & 0x0f;
- h->version.jtag = (v >> 6) & 0x3f;
- h->version.swim = v & 0x3f;
- h->vid = buf_get_u32(h->databuf, 16, 16);
- h->pid = buf_get_u32(h->databuf, 32, 16);
+ /* STLINK-V3 requires a specific command */
+ if (v == 3 && x == 0 && y == 0) {
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
- /* set the supported jtag api version
- * API V2 is supported since JTAG V11
- */
- if (h->version.jtag >= 11)
- h->version.jtag_api_max = STLINK_JTAG_API_V2;
- else
- h->version.jtag_api_max = STLINK_JTAG_API_V1;
+ h->cmdbuf[h->cmdidx++] = STLINK_APIV3_GET_VERSION_EX;
+
+ res = stlink_usb_xfer(handle, h->databuf, 12);
+ if (res != ERROR_OK)
+ return res;
+
+ v = h->databuf[0];
+ swim = h->databuf[1];
+ jtag = h->databuf[2];
+ msd = h->databuf[3];
+ bridge = h->databuf[4];
+ h->vid = le_to_h_u16(h->databuf + 8);
+ h->pid = le_to_h_u16(h->databuf + 10);
+ }
+
+ h->version.stlink = v;
+ h->version.jtag = jtag;
+ h->version.swim = swim;
+
+ flags = 0;
+ switch (h->version.stlink) {
+ case 1:
+ /* ST-LINK/V1 from J11 switch to api-v2 (and support SWD) */
+ if (h->version.jtag >= 11)
+ h->version.jtag_api = STLINK_JTAG_API_V2;
+ else
+ h->version.jtag_api = STLINK_JTAG_API_V1;
+
+ break;
+ case 2:
+ /* all ST-LINK/V2 and ST-Link/V2.1 use api-v2 */
+ h->version.jtag_api = STLINK_JTAG_API_V2;
+
+ /* API for trace from J13 */
+ /* API for target voltage from J13 */
+ if (h->version.jtag >= 13)
+ flags |= STLINK_F_HAS_TRACE;
+
+ /* preferred API to get last R/W status from J15 */
+ if (h->version.jtag >= 15)
+ flags |= STLINK_F_HAS_GETLASTRWSTATUS2;
+
+ /* API to set SWD frequency from J22 */
+ if (h->version.jtag >= 22)
+ flags |= STLINK_F_HAS_SWD_SET_FREQ;
+
+ /* API to set JTAG frequency from J24 */
+ if (h->version.jtag >= 24)
+ flags |= STLINK_F_HAS_JTAG_SET_FREQ;
+
+ /* API to read/write memory at 16 bit from J26 */
+ if (h->version.jtag >= 26)
+ flags |= STLINK_F_HAS_MEM_16BIT;
+
+ break;
+ case 3:
+ /* all STLINK-V3 use api-v3 */
+ h->version.jtag_api = STLINK_JTAG_API_V3;
+
+ /* STLINK-V3 is a superset of ST-LINK/V2 */
+
+ /* API for trace */
+ /* API for target voltage */
+ flags |= STLINK_F_HAS_TRACE;
+
+ /* preferred API to get last R/W status */
+ flags |= STLINK_F_HAS_GETLASTRWSTATUS2;
+
+ /* API to read/write memory at 16 bit */
+ flags |= STLINK_F_HAS_MEM_16BIT;
- LOG_INFO("STLINK v%d JTAG v%d API v%d SWIM v%d VID 0x%04X PID 0x%04X",
- h->version.stlink,
- h->version.jtag,
- (h->version.jtag_api_max == STLINK_JTAG_API_V1) ? 1 : 2,
- h->version.swim,
+ break;
+ default:
+ break;
+ }
+ h->version.flags = flags;
+
+ p = v_str;
+ p += sprintf(p, "V%d", v);
+ if (jtag || !msd)
+ p += sprintf(p, "J%d", jtag);
+ if (msd)
+ p += sprintf(p, "M%d", msd);
+ if (bridge)
+ p += sprintf(p, "B%d", bridge);
+ if (swim || !msd)
+ p += sprintf(p, "S%d", swim);
+
+ LOG_INFO("STLINK %s (API v%d) VID:PID %04X:%04X",
+ v_str,
+ h->version.jtag_api,
h->vid,
h->pid);
struct stlink_usb_handle_s *h = handle;
uint32_t adc_results[2];
- /* only supported by stlink/v2 and for firmware >= 13 */
- if (h->version.stlink == 1 || h->version.jtag < 13)
+ /* no error message, simply quit with error */
+ if (!(h->version.flags & STLINK_F_HAS_TARGET_VOLT))
return ERROR_COMMAND_NOTFOUND;
stlink_usb_init_buffer(handle, h->rx_ep, 8);
assert(handle != NULL);
- /* only supported by stlink/v2 and for firmware >= 22 */
- if (h->version.stlink == 1 || h->version.jtag < 22)
+ if (!(h->version.flags & STLINK_F_HAS_SWD_SET_FREQ))
return ERROR_COMMAND_NOTFOUND;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
assert(handle != NULL);
- /* only supported by stlink/v2 and for firmware >= 24 */
- if (h->version.stlink == 1 || h->version.jtag < 24)
+ if (!(h->version.flags & STLINK_F_HAS_JTAG_SET_FREQ))
return ERROR_COMMAND_NOTFOUND;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
* status
* TODO: we need the test on api V1 too
*/
- if (h->jtag_api == STLINK_JTAG_API_V2)
+ if (h->version.jtag_api != STLINK_JTAG_API_V1)
rx_size = 2;
stlink_usb_init_buffer(handle, h->rx_ep, rx_size);
switch (type) {
case STLINK_MODE_DEBUG_JTAG:
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_ENTER;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_ENTER;
- h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_ENTER_JTAG;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_ENTER_JTAG_NO_RESET;
break;
case STLINK_MODE_DEBUG_SWD:
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_ENTER;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_ENTER;
- h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_ENTER_SWD;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_ENTER_SWD_NO_RESET;
break;
case STLINK_MODE_DEBUG_SWIM:
h->cmdbuf[h->cmdidx++] = STLINK_SWIM_COMMAND;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_WRITEDEBUGREG;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_WRITEDEBUGREG;
assert(handle != NULL);
- if (h->trace.enabled && h->version.jtag >= STLINK_TRACE_MIN_VERSION) {
+ if (h->trace.enabled && (h->version.flags & STLINK_F_HAS_TRACE)) {
int res;
stlink_usb_init_buffer(handle, h->rx_ep, 10);
h->reconnect_pending = false;
}
- if (h->jtag_api == STLINK_JTAG_API_V2) {
+ if (h->version.jtag_api != STLINK_JTAG_API_V1) {
res = stlink_usb_v2_get_status(handle);
if (res == TARGET_UNKNOWN)
h->reconnect_pending = true;
assert(handle != NULL);
- assert(h->version.jtag >= STLINK_TRACE_MIN_VERSION);
+ assert(h->version.flags & STLINK_F_HAS_TRACE);
LOG_DEBUG("Tracing: disable");
assert(handle != NULL);
- if (h->version.jtag >= STLINK_TRACE_MIN_VERSION) {
+ if (h->version.flags & STLINK_F_HAS_TRACE) {
stlink_usb_init_buffer(handle, h->rx_ep, 10);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_RESETSYS;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_RESETSYS;
assert(handle != NULL);
- if (h->jtag_api == STLINK_JTAG_API_V2) {
+ if (h->version.jtag_api != STLINK_JTAG_API_V1) {
res = stlink_usb_write_debug_reg(handle, DCB_DHCSR, DBGKEY|C_DEBUGEN);
return res;
assert(handle != NULL);
- if (h->jtag_api == STLINK_JTAG_API_V2) {
+ if (h->version.jtag_api != STLINK_JTAG_API_V1) {
res = stlink_usb_write_debug_reg(handle, DCB_DHCSR, DBGKEY|C_HALT|C_DEBUGEN);
return res;
assert(handle != NULL);
- if (h->jtag_api == STLINK_JTAG_API_V2) {
+ if (h->version.jtag_api != STLINK_JTAG_API_V1) {
/* TODO: this emulates the v1 api, it should really use a similar auto mask isr
* that the Cortex-M3 currently does. */
stlink_usb_write_debug_reg(handle, DCB_DHCSR, DBGKEY|C_HALT|C_MASKINTS|C_DEBUGEN);
stlink_usb_init_buffer(handle, h->rx_ep, 84);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_READALLREGS;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READALLREGS;
assert(handle != NULL);
- stlink_usb_init_buffer(handle, h->rx_ep, h->jtag_api == STLINK_JTAG_API_V1 ? 4 : 8);
+ stlink_usb_init_buffer(handle, h->rx_ep, h->version.jtag_api == STLINK_JTAG_API_V1 ? 4 : 8);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_READREG;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READREG;
h->cmdbuf[h->cmdidx++] = num;
- if (h->jtag_api == STLINK_JTAG_API_V1) {
+ if (h->version.jtag_api == STLINK_JTAG_API_V1) {
res = stlink_usb_xfer(handle, h->databuf, 4);
if (res != ERROR_OK)
return res;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV1_WRITEREG;
else
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_WRITEREG;
assert(handle != NULL);
- if (h->jtag_api == STLINK_JTAG_API_V1)
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
return ERROR_OK;
stlink_usb_init_buffer(handle, h->rx_ep, 2);
h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
- h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GETLASTRWSTATUS;
+ if (h->version.flags & STLINK_F_HAS_GETLASTRWSTATUS2) {
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GETLASTRWSTATUS2;
- res = stlink_usb_xfer(handle, h->databuf, 2);
+ res = stlink_usb_xfer(handle, h->databuf, 12);
+ } else {
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_GETLASTRWSTATUS;
+
+ res = stlink_usb_xfer(handle, h->databuf, 2);
+ }
if (res != ERROR_OK)
return res;
assert(handle != NULL);
- /* max 8bit read/write is 64bytes */
- if (len > STLINK_MAX_RW8) {
- LOG_DEBUG("max buffer length exceeded");
+ /* max 8 bit read/write is 64 bytes or 512 bytes for v3 */
+ if (len > stlink_usb_block(h)) {
+ LOG_DEBUG("max buffer (%d) length exceeded", stlink_usb_block(h));
return ERROR_FAIL;
}
assert(handle != NULL);
- /* max 8bit read/write is 64bytes */
- if (len > STLINK_MAX_RW8) {
- LOG_DEBUG("max buffer length exceeded");
+ /* max 8 bit read/write is 64 bytes or 512 bytes for v3 */
+ if (len > stlink_usb_block(h)) {
+ LOG_DEBUG("max buffer length (%d) exceeded", stlink_usb_block(h));
return ERROR_FAIL;
}
return stlink_usb_get_rw_status(handle);
}
+/** */
+static int stlink_usb_read_mem16(void *handle, uint32_t addr, uint16_t len,
+ uint8_t *buffer)
+{
+ int res;
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_MEM_16BIT))
+ return ERROR_COMMAND_NOTFOUND;
+
+ /* data must be a multiple of 2 and half-word aligned */
+ if (len % 2 || addr % 2) {
+ LOG_DEBUG("Invalid data alignment");
+ return ERROR_TARGET_UNALIGNED_ACCESS;
+ }
+
+ stlink_usb_init_buffer(handle, h->rx_ep, len);
+
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_READMEM_16BIT;
+ h_u32_to_le(h->cmdbuf+h->cmdidx, addr);
+ h->cmdidx += 4;
+ h_u16_to_le(h->cmdbuf+h->cmdidx, len);
+ h->cmdidx += 2;
+
+ res = stlink_usb_xfer(handle, h->databuf, len);
+
+ if (res != ERROR_OK)
+ return res;
+
+ memcpy(buffer, h->databuf, len);
+
+ return stlink_usb_get_rw_status(handle);
+}
+
+/** */
+static int stlink_usb_write_mem16(void *handle, uint32_t addr, uint16_t len,
+ const uint8_t *buffer)
+{
+ int res;
+ struct stlink_usb_handle_s *h = handle;
+
+ assert(handle != NULL);
+
+ if (!(h->version.flags & STLINK_F_HAS_MEM_16BIT))
+ return ERROR_COMMAND_NOTFOUND;
+
+ /* data must be a multiple of 2 and half-word aligned */
+ if (len % 2 || addr % 2) {
+ LOG_DEBUG("Invalid data alignment");
+ return ERROR_TARGET_UNALIGNED_ACCESS;
+ }
+
+ stlink_usb_init_buffer(handle, h->tx_ep, len);
+
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_APIV2_WRITEMEM_16BIT;
+ h_u32_to_le(h->cmdbuf+h->cmdidx, addr);
+ h->cmdidx += 4;
+ h_u16_to_le(h->cmdbuf+h->cmdidx, len);
+ h->cmdidx += 2;
+
+ res = stlink_usb_xfer(handle, buffer, len);
+
+ if (res != ERROR_OK)
+ return res;
+
+ return stlink_usb_get_rw_status(handle);
+}
+
/** */
static int stlink_usb_read_mem32(void *handle, uint32_t addr, uint16_t len,
uint8_t *buffer)
/* calculate byte count */
count *= size;
+ /* switch to 8 bit if stlink does not support 16 bit memory read */
+ if (size == 2 && !(h->version.flags & STLINK_F_HAS_MEM_16BIT))
+ size = 1;
+
while (count) {
- bytes_remaining = (size == 4) ? \
- stlink_max_block_size(h->max_mem_packet, addr) : STLINK_MAX_RW8;
+ bytes_remaining = (size != 1) ? \
+ stlink_max_block_size(h->max_mem_packet, addr) : stlink_usb_block(h);
if (count < bytes_remaining)
bytes_remaining = count;
if (retval != ERROR_OK)
return retval;
} else
- /* the stlink only supports 8/32bit memory read/writes
- * honour 32bit, all others will be handled as 8bit access */
- if (size == 4) {
-
- /* When in jtag mode the stlink uses the auto-increment functinality.
+ /*
+ * all stlink support 8/32bit memory read/writes and only from
+ * stlink V2J26 there is support for 16 bit memory read/write.
+ * Honour 32 bit and, if possible, 16 bit too. Otherwise, handle
+ * as 8bit access.
+ */
+ if (size != 1) {
+
+ /* When in jtag mode the stlink uses the auto-increment functionality.
* However it expects us to pass the data correctly, this includes
* alignment and any page boundaries. We already do this as part of the
* adi_v5 implementation, but the stlink is a hla adapter and so this
- * needs implementiong manually.
+ * needs implementing manually.
* currently this only affects jtag mode, according to ST they do single
* access in SWD mode - but this may change and so we do it for both modes */
/* we first need to check for any unaligned bytes */
- if (addr % 4) {
+ if (addr & (size - 1)) {
- uint32_t head_bytes = 4 - (addr % 4);
+ uint32_t head_bytes = size - (addr & (size - 1));
retval = stlink_usb_read_mem8(handle, addr, head_bytes, buffer);
if (retval == ERROR_WAIT && retries < MAX_WAIT_RETRIES) {
usleep((1<<retries++) * 1000);
bytes_remaining -= head_bytes;
}
- if (bytes_remaining % 4)
+ if (bytes_remaining & (size - 1))
retval = stlink_usb_read_mem(handle, addr, 1, bytes_remaining, buffer);
+ else if (size == 2)
+ retval = stlink_usb_read_mem16(handle, addr, bytes_remaining, buffer);
else
retval = stlink_usb_read_mem32(handle, addr, bytes_remaining, buffer);
} else
/* calculate byte count */
count *= size;
+ /* switch to 8 bit if stlink does not support 16 bit memory read */
+ if (size == 2 && !(h->version.flags & STLINK_F_HAS_MEM_16BIT))
+ size = 1;
+
while (count) {
- bytes_remaining = (size == 4) ? \
- stlink_max_block_size(h->max_mem_packet, addr) : STLINK_MAX_RW8;
+ bytes_remaining = (size != 1) ? \
+ stlink_max_block_size(h->max_mem_packet, addr) : stlink_usb_block(h);
if (count < bytes_remaining)
bytes_remaining = count;
if (retval != ERROR_OK)
return retval;
} else
- /* the stlink only supports 8/32bit memory read/writes
- * honour 32bit, all others will be handled as 8bit access */
- if (size == 4) {
-
- /* When in jtag mode the stlink uses the auto-increment functinality.
+ /*
+ * all stlink support 8/32bit memory read/writes and only from
+ * stlink V2J26 there is support for 16 bit memory read/write.
+ * Honour 32 bit and, if possible, 16 bit too. Otherwise, handle
+ * as 8bit access.
+ */
+ if (size != 1) {
+
+ /* When in jtag mode the stlink uses the auto-increment functionality.
* However it expects us to pass the data correctly, this includes
* alignment and any page boundaries. We already do this as part of the
* adi_v5 implementation, but the stlink is a hla adapter and so this
- * needs implementiong manually.
+ * needs implementing manually.
* currently this only affects jtag mode, according to ST they do single
* access in SWD mode - but this may change and so we do it for both modes */
/* we first need to check for any unaligned bytes */
- if (addr % 4) {
+ if (addr & (size - 1)) {
- uint32_t head_bytes = 4 - (addr % 4);
+ uint32_t head_bytes = size - (addr & (size - 1));
retval = stlink_usb_write_mem8(handle, addr, head_bytes, buffer);
if (retval == ERROR_WAIT && retries < MAX_WAIT_RETRIES) {
usleep((1<<retries++) * 1000);
bytes_remaining -= head_bytes;
}
- if (bytes_remaining % 4)
+ if (bytes_remaining & (size - 1))
retval = stlink_usb_write_mem(handle, addr, 1, bytes_remaining, buffer);
+ else if (size == 2)
+ retval = stlink_usb_write_mem16(handle, addr, bytes_remaining, buffer);
else
retval = stlink_usb_write_mem32(handle, addr, bytes_remaining, buffer);
unsigned int i;
int speed_index = -1;
int speed_diff = INT_MAX;
+ int last_valid_speed = -1;
bool match = true;
for (i = 0; i < map_size; i++) {
+ if (!map[i].speed)
+ continue;
+ last_valid_speed = i;
if (khz == map[i].speed) {
speed_index = i;
break;
if (speed_index == -1) {
/* this will only be here if we cannot match the slow speed.
* use the slowest speed we support.*/
- speed_index = map_size - 1;
+ speed_index = last_valid_speed;
match = false;
} else if (i == map_size)
match = false;
int speed_index;
struct stlink_usb_handle_s *h = handle;
- /* only supported by stlink/v2 and for firmware >= 22 */
- if (h->version.stlink == 1 || h->version.jtag < 22)
+ /* old firmware cannot change it */
+ if (!(h->version.flags & STLINK_F_HAS_SWD_SET_FREQ))
return khz;
speed_index = stlink_match_speed_map(stlink_khz_to_speed_map_swd,
int speed_index;
struct stlink_usb_handle_s *h = handle;
- /* only supported by stlink/v2 and for firmware >= 24 */
- if (h->version.stlink == 1 || h->version.jtag < 24)
+ /* old firmware cannot change it */
+ if (!(h->version.flags & STLINK_F_HAS_JTAG_SET_FREQ))
return khz;
speed_index = stlink_match_speed_map(stlink_khz_to_speed_map_jtag,
LOG_DEBUG("Supported clock speeds are:");
for (i = 0; i < map_size; i++)
- LOG_DEBUG("%d kHz", map[i].speed);
+ if (map[i].speed)
+ LOG_DEBUG("%d kHz", map[i].speed);
+}
+
+static int stlink_get_com_freq(void *handle, bool is_jtag, struct speed_map *map)
+{
+ struct stlink_usb_handle_s *h = handle;
+ int i;
+
+ if (h->version.jtag_api != STLINK_JTAG_API_V3) {
+ LOG_ERROR("Unknown command");
+ return 0;
+ }
+
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_APIV3_GET_COM_FREQ;
+ h->cmdbuf[h->cmdidx++] = is_jtag ? 1 : 0;
+
+ int res = stlink_usb_xfer(handle, h->databuf, 52);
+
+ int size = h->databuf[8];
+
+ if (size > STLINK_V3_MAX_FREQ_NB)
+ size = STLINK_V3_MAX_FREQ_NB;
+
+ for (i = 0; i < size; i++) {
+ map[i].speed = le_to_h_u32(&h->databuf[12 + 4 * i]);
+ map[i].speed_divisor = i;
+ }
+
+ /* set to zero all the next entries */
+ for (i = size; i < STLINK_V3_MAX_FREQ_NB; i++)
+ map[i].speed = 0;
+
+ return res;
+}
+
+static int stlink_set_com_freq(void *handle, bool is_jtag, unsigned int frequency)
+{
+ struct stlink_usb_handle_s *h = handle;
+
+ if (h->version.jtag_api != STLINK_JTAG_API_V3) {
+ LOG_ERROR("Unknown command");
+ return 0;
+ }
+
+ stlink_usb_init_buffer(handle, h->rx_ep, 16);
+
+ h->cmdbuf[h->cmdidx++] = STLINK_DEBUG_COMMAND;
+ h->cmdbuf[h->cmdidx++] = STLINK_APIV3_SET_COM_FREQ;
+ h->cmdbuf[h->cmdidx++] = is_jtag ? 1 : 0;
+ h->cmdbuf[h->cmdidx++] = 0;
+
+ h_u32_to_le(&h->cmdbuf[4], frequency);
+
+ return stlink_usb_xfer(handle, h->databuf, 8);
+}
+
+static int stlink_speed_v3(void *handle, bool is_jtag, int khz, bool query)
+{
+ struct stlink_usb_handle_s *h = handle;
+ int speed_index;
+ struct speed_map map[STLINK_V3_MAX_FREQ_NB];
+
+ stlink_get_com_freq(h, is_jtag, map);
+
+ speed_index = stlink_match_speed_map(map, ARRAY_SIZE(map), khz, query);
+
+ if (!query) {
+ int result = stlink_set_com_freq(h, is_jtag, map[speed_index].speed);
+ if (result != ERROR_OK) {
+ LOG_ERROR("Unable to set adapter speed");
+ return khz;
+ }
+ }
+ return map[speed_index].speed;
}
static int stlink_speed(void *handle, int khz, bool query)
if (!handle)
return khz;
- if (h->transport == HL_TRANSPORT_SWIM)
+ switch (h->transport) {
+ case HL_TRANSPORT_SWIM:
return stlink_speed_swim(handle, khz, query);
- else if (h->transport == HL_TRANSPORT_SWD)
- return stlink_speed_swd(handle, khz, query);
- else if (h->transport == HL_TRANSPORT_JTAG)
- return stlink_speed_jtag(handle, khz, query);
+ break;
+ case HL_TRANSPORT_SWD:
+ if (h->version.jtag_api == STLINK_JTAG_API_V3)
+ return stlink_speed_v3(handle, false, khz, query);
+ else
+ return stlink_speed_swd(handle, khz, query);
+ break;
+ case HL_TRANSPORT_JTAG:
+ if (h->version.jtag_api == STLINK_JTAG_API_V3)
+ return stlink_speed_v3(handle, true, khz, query);
+ else
+ return stlink_speed_jtag(handle, khz, query);
+ break;
+ default:
+ break;
+ }
return khz;
}
{
int err, retry_count = 1;
struct stlink_usb_handle_s *h;
- enum stlink_jtag_api_version api;
LOG_DEBUG("stlink_usb_open");
case STLINK_V1_PID:
h->version.stlink = 1;
h->tx_ep = STLINK_TX_EP;
- h->trace_ep = STLINK_TRACE_EP;
+ break;
+ case STLINK_V3_USBLOADER_PID:
+ case STLINK_V3E_PID:
+ case STLINK_V3S_PID:
+ case STLINK_V3_2VCP_PID:
+ h->version.stlink = 3;
+ h->tx_ep = STLINK_V2_1_TX_EP;
+ h->trace_ep = STLINK_V2_1_TRACE_EP;
break;
case STLINK_V2_1_PID:
case STLINK_V2_1_NO_MSD_PID:
switch (h->transport) {
case HL_TRANSPORT_SWD:
+ if (h->version.jtag_api == STLINK_JTAG_API_V1)
+ err = ERROR_FAIL;
+ /* fall-through */
case HL_TRANSPORT_JTAG:
if (h->version.jtag == 0)
err = ERROR_FAIL;
goto error_open;
}
- api = h->version.jtag_api_max;
-
- LOG_INFO("using stlink api v%d", api);
-
- /* set the used jtag api, this will default to the newest supported version */
- h->jtag_api = api;
-
/* initialize the debug hardware */
err = stlink_usb_init_mode(h, param->connect_under_reset);
}
if (h->transport == HL_TRANSPORT_JTAG) {
- /* jtag clock speed only supported by stlink/v2 and for firmware >= 24 */
- if (h->version.stlink >= 2 && h->version.jtag >= 24) {
+ if (h->version.flags & STLINK_F_HAS_JTAG_SET_FREQ) {
stlink_dump_speed_map(stlink_khz_to_speed_map_jtag, ARRAY_SIZE(stlink_khz_to_speed_map_jtag));
stlink_speed(h, param->initial_interface_speed, false);
}
} else if (h->transport == HL_TRANSPORT_SWD) {
- /* clock speed only supported by stlink/v2 and for firmware >= 22 */
- if (h->version.stlink >= 2 && h->version.jtag >= 22) {
+ if (h->version.flags & STLINK_F_HAS_SWD_SET_FREQ) {
stlink_dump_speed_map(stlink_khz_to_speed_map_swd, ARRAY_SIZE(stlink_khz_to_speed_map_swd));
stlink_speed(h, param->initial_interface_speed, false);
}
}
+ if (h->version.jtag_api == STLINK_JTAG_API_V3) {
+ struct speed_map map[STLINK_V3_MAX_FREQ_NB];
+
+ stlink_get_com_freq(h, (h->transport == HL_TRANSPORT_JTAG), map);
+ stlink_dump_speed_map(map, ARRAY_SIZE(map));
+ stlink_speed(h, param->initial_interface_speed, false);
+ }
+
/* get cpuid, so we can determine the max page size
* start with a safe default */
h->max_mem_packet = (1 << 10);
{
struct stlink_usb_handle_s *h = handle;
- if (enabled && (h->jtag_api < 2 ||
+ if (enabled && (!(h->version.flags & STLINK_F_HAS_TRACE) ||
pin_protocol != TPIU_PIN_PROTOCOL_ASYNC_UART)) {
LOG_ERROR("The attached ST-LINK version doesn't support this trace mode");
return ERROR_FAIL;