#endif
#include "imp.h"
+#include <helper/align.h>
#include <helper/binarybuffer.h>
#include <target/algorithm.h>
-#include <target/armv7m.h>
+#include <target/cortex_m.h>
#include "bits.h"
+#include "stm32l4x.h"
/* STM32L4xxx series for reference.
*
*
*/
+/* STM32WBxxx series for reference.
+ *
+ * RM0434 (STM32WB55)
+ * http://www.st.com/resource/en/reference_manual/dm00318631.pdf
+ *
+ * RM0471 (STM32WB50)
+ * http://www.st.com/resource/en/reference_manual/dm00622834.pdf
+ */
+
+/* STM32WLxxx series for reference.
+ *
+ * RM0461 (STM32WLEx)
+ * http://www.st.com/resource/en/reference_manual/dm00530369.pdf
+ *
+ * RM0453 (STM32WL5x)
+ * http://www.st.com/resource/en/reference_manual/dm00451556.pdf
+ */
+
+/* STM32G0xxx series for reference.
+ *
+ * RM0444 (STM32G0x1)
+ * http://www.st.com/resource/en/reference_manual/dm00371828.pdf
+ *
+ * RM0454 (STM32G0x0)
+ * http://www.st.com/resource/en/reference_manual/dm00463896.pdf
+ */
+
+/* STM32G4xxx series for reference.
+ *
+ * RM0440 (STM32G43x/44x/47x/48x/49x/4Ax)
+ * http://www.st.com/resource/en/reference_manual/dm00355726.pdf
+ *
+ * Cat. 2 devices have single bank only, page size is 2kByte.
+ *
+ * Cat. 3 devices have single and dual bank operating modes,
+ * Page size is 2kByte (dual mode) or 4kByte (single mode).
+ *
+ * Bank mode is controlled by bit 22 (DBANK) in option bytes register.
+ * Both banks are treated as a single OpenOCD bank.
+ *
+ * Cat. 4 devices have single bank only, page size is 2kByte.
+ */
+
+/* STM32L5xxx series for reference.
+ *
+ * RM0428 (STM32L552xx/STM32L562xx)
+ * http://www.st.com/resource/en/reference_manual/dm00346336.pdf
+ */
+
/* Erase time can be as high as 25ms, 10x this and assume it's toast... */
#define FLASH_ERASE_TIMEOUT 250
+#define FLASH_WRITE_TIMEOUT 50
+
+
+/* relevant STM32L4 flags ****************************************************/
+#define F_NONE 0
+/* this flag indicates if the device flash is with dual bank architecture */
+#define F_HAS_DUAL_BANK BIT(0)
+/* this flags is used for dual bank devices only, it indicates if the
+ * 4 WRPxx are usable if the device is configured in single-bank mode */
+#define F_USE_ALL_WRPXX BIT(1)
+/* this flag indicates if the device embeds a TrustZone security feature */
+#define F_HAS_TZ BIT(2)
+/* this flag indicates if the device has the same flash registers as STM32L5 */
+#define F_HAS_L5_FLASH_REGS BIT(3)
+/* end of STM32L4 flags ******************************************************/
+
+
+enum stm32l4_flash_reg_index {
+ STM32_FLASH_ACR_INDEX,
+ STM32_FLASH_KEYR_INDEX,
+ STM32_FLASH_OPTKEYR_INDEX,
+ STM32_FLASH_SR_INDEX,
+ STM32_FLASH_CR_INDEX,
+ /* for some devices like STM32WL5x, the CPU2 have a dedicated C2CR register w/o LOCKs,
+ * so it uses the C2CR for flash operations and CR for checking locks and locking */
+ STM32_FLASH_CR_WLK_INDEX, /* FLASH_CR_WITH_LOCK */
+ STM32_FLASH_OPTR_INDEX,
+ STM32_FLASH_WRP1AR_INDEX,
+ STM32_FLASH_WRP1BR_INDEX,
+ STM32_FLASH_WRP2AR_INDEX,
+ STM32_FLASH_WRP2BR_INDEX,
+ STM32_FLASH_REG_INDEX_NUM,
+};
-/* Flash registers offsets */
-#define STM32_FLASH_ACR 0x00
-#define STM32_FLASH_KEYR 0x08
-#define STM32_FLASH_OPTKEYR 0x0c
-#define STM32_FLASH_SR 0x10
-#define STM32_FLASH_CR 0x14
-#define STM32_FLASH_OPTR 0x20
-#define STM32_FLASH_WRP1AR 0x2c
-#define STM32_FLASH_WRP1BR 0x30
-#define STM32_FLASH_WRP2AR 0x4c
-#define STM32_FLASH_WRP2BR 0x50
-
-/* FLASH_CR register bits */
-#define FLASH_PG (1 << 0)
-#define FLASH_PER (1 << 1)
-#define FLASH_MER1 (1 << 2)
-#define FLASH_PAGE_SHIFT 3
-#define FLASH_CR_BKER (1 << 11)
-#define FLASH_MER2 (1 << 15)
-#define FLASH_STRT (1 << 16)
-#define FLASH_OPTSTRT (1 << 17)
-#define FLASH_EOPIE (1 << 24)
-#define FLASH_ERRIE (1 << 25)
-#define FLASH_OBLLAUNCH (1 << 27)
-#define FLASH_OPTLOCK (1 << 30)
-#define FLASH_LOCK (1 << 31)
-
-/* FLASH_SR register bits */
-#define FLASH_BSY (1 << 16)
-/* Fast programming not used => related errors not used*/
-#define FLASH_PGSERR (1 << 7) /* Programming sequence error */
-#define FLASH_SIZERR (1 << 6) /* Size error */
-#define FLASH_PGAERR (1 << 5) /* Programming alignment error */
-#define FLASH_WRPERR (1 << 4) /* Write protection error */
-#define FLASH_PROGERR (1 << 3) /* Programming error */
-#define FLASH_OPERR (1 << 1) /* Operation error */
-#define FLASH_EOP (1 << 0) /* End of operation */
-#define FLASH_ERROR (FLASH_PGSERR | FLASH_PGSERR | FLASH_PGAERR | FLASH_WRPERR | FLASH_OPERR)
-
-/* register unlock keys */
-#define KEY1 0x45670123
-#define KEY2 0xCDEF89AB
-
-/* option register unlock key */
-#define OPTKEY1 0x08192A3B
-#define OPTKEY2 0x4C5D6E7F
-
-#define RDP_LEVEL_0 0xAA
-#define RDP_LEVEL_1 0xBB
-#define RDP_LEVEL_2 0xCC
-
-
-/* other registers */
-#define DBGMCU_IDCODE 0xE0042000
+enum stm32l4_rdp {
+ RDP_LEVEL_0 = 0xAA,
+ RDP_LEVEL_0_5 = 0x55, /* for devices with TrustZone enabled */
+ RDP_LEVEL_1 = 0x00,
+ RDP_LEVEL_2 = 0xCC
+};
+static const uint32_t stm32l4_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
+ [STM32_FLASH_ACR_INDEX] = 0x000,
+ [STM32_FLASH_KEYR_INDEX] = 0x008,
+ [STM32_FLASH_OPTKEYR_INDEX] = 0x00C,
+ [STM32_FLASH_SR_INDEX] = 0x010,
+ [STM32_FLASH_CR_INDEX] = 0x014,
+ [STM32_FLASH_OPTR_INDEX] = 0x020,
+ [STM32_FLASH_WRP1AR_INDEX] = 0x02C,
+ [STM32_FLASH_WRP1BR_INDEX] = 0x030,
+ [STM32_FLASH_WRP2AR_INDEX] = 0x04C,
+ [STM32_FLASH_WRP2BR_INDEX] = 0x050,
+};
+
+static const uint32_t stm32wl_cpu2_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
+ [STM32_FLASH_ACR_INDEX] = 0x000,
+ [STM32_FLASH_KEYR_INDEX] = 0x008,
+ [STM32_FLASH_OPTKEYR_INDEX] = 0x010,
+ [STM32_FLASH_SR_INDEX] = 0x060,
+ [STM32_FLASH_CR_INDEX] = 0x064,
+ [STM32_FLASH_CR_WLK_INDEX] = 0x014,
+ [STM32_FLASH_OPTR_INDEX] = 0x020,
+ [STM32_FLASH_WRP1AR_INDEX] = 0x02C,
+ [STM32_FLASH_WRP1BR_INDEX] = 0x030,
+};
+
+static const uint32_t stm32l5_ns_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
+ [STM32_FLASH_ACR_INDEX] = 0x000,
+ [STM32_FLASH_KEYR_INDEX] = 0x008, /* NSKEYR */
+ [STM32_FLASH_OPTKEYR_INDEX] = 0x010,
+ [STM32_FLASH_SR_INDEX] = 0x020, /* NSSR */
+ [STM32_FLASH_CR_INDEX] = 0x028, /* NSCR */
+ [STM32_FLASH_OPTR_INDEX] = 0x040,
+ [STM32_FLASH_WRP1AR_INDEX] = 0x058,
+ [STM32_FLASH_WRP1BR_INDEX] = 0x05C,
+ [STM32_FLASH_WRP2AR_INDEX] = 0x068,
+ [STM32_FLASH_WRP2BR_INDEX] = 0x06C,
+};
+
+static const uint32_t stm32l5_s_flash_regs[STM32_FLASH_REG_INDEX_NUM] = {
+ [STM32_FLASH_ACR_INDEX] = 0x000,
+ [STM32_FLASH_KEYR_INDEX] = 0x00C, /* SECKEYR */
+ [STM32_FLASH_OPTKEYR_INDEX] = 0x010,
+ [STM32_FLASH_SR_INDEX] = 0x024, /* SECSR */
+ [STM32_FLASH_CR_INDEX] = 0x02C, /* SECCR */
+ [STM32_FLASH_OPTR_INDEX] = 0x040,
+ [STM32_FLASH_WRP1AR_INDEX] = 0x058,
+ [STM32_FLASH_WRP1BR_INDEX] = 0x05C,
+ [STM32_FLASH_WRP2AR_INDEX] = 0x068,
+ [STM32_FLASH_WRP2BR_INDEX] = 0x06C,
+};
struct stm32l4_rev {
const uint16_t rev;
const struct stm32l4_rev *revs;
const size_t num_revs;
const uint16_t max_flash_size_kb;
- const bool has_dual_bank;
+ const uint32_t flags; /* one bit per feature, see STM32L4 flags: macros F_XXX */
const uint32_t flash_regs_base;
const uint32_t fsize_addr;
+ const uint32_t otp_base;
+ const uint32_t otp_size;
};
struct stm32l4_flash_bank {
- int probed;
+ bool probed;
uint32_t idcode;
- int bank1_sectors;
+ unsigned int bank1_sectors;
bool dual_bank_mode;
int hole_sectors;
+ uint32_t user_bank_size;
+ uint32_t cr_bker_mask;
+ uint32_t sr_bsy_mask;
+ uint32_t wrpxxr_mask;
const struct stm32l4_part_info *part_info;
+ uint32_t flash_regs_base;
+ const uint32_t *flash_regs;
+ bool otp_enabled;
+ bool use_flashloader;
+ enum stm32l4_rdp rdp;
+ bool tzen;
+ uint32_t optr;
};
+enum stm32_bank_id {
+ STM32_BANK1,
+ STM32_BANK2,
+ STM32_ALL_BANKS
+};
+
+struct stm32l4_wrp {
+ enum stm32l4_flash_reg_index reg_idx;
+ uint32_t value;
+ bool used;
+ int first;
+ int last;
+ int offset;
+};
+
+/* human readable list of families this drivers supports (sorted alphabetically) */
+static const char *device_families = "STM32G0/G4/L4/L4+/L5/WB/WL";
+
static const struct stm32l4_rev stm32_415_revs[] = {
{ 0x1000, "1" }, { 0x1001, "2" }, { 0x1003, "3" }, { 0x1007, "4" }
};
{ 0x1000, "A" }, { 0x1001, "Z" }, { 0x2001, "Y" },
};
+static const struct stm32l4_rev stm32_460_revs[] = {
+ { 0x1000, "A/Z" } /* A and Z, no typo in RM! */, { 0x2000, "B" },
+};
+
static const struct stm32l4_rev stm32_461_revs[] = {
{ 0x1000, "A" }, { 0x2000, "B" },
};
static const struct stm32l4_rev stm32_462_revs[] = {
- { 0x1000, "A" }, { 0x1001, "Z" }, { 0x2001, "Y" },
+ { 0x1000, "A" }, { 0x1001, "Z" }, { 0x2001, "Y" },
};
static const struct stm32l4_rev stm32_464_revs[] = {
+ { 0x1000, "A" }, { 0x1001, "Z" }, { 0x2001, "Y" },
+};
+
+static const struct stm32l4_rev stm32_466_revs[] = {
+ { 0x1000, "A" }, { 0x1001, "Z" }, { 0x2000, "B" },
+};
+
+static const struct stm32l4_rev stm32_467_revs[] = {
{ 0x1000, "A" },
};
+static const struct stm32l4_rev stm32_468_revs[] = {
+ { 0x1000, "A" }, { 0x2000, "B" }, { 0x2001, "Z" },
+};
+
+static const struct stm32l4_rev stm32_469_revs[] = {
+ { 0x1000, "A" }, { 0x2000, "B" }, { 0x2001, "Z" },
+};
+
static const struct stm32l4_rev stm32_470_revs[] = {
{ 0x1000, "A" }, { 0x1001, "Z" }, { 0x1003, "Y" }, { 0x100F, "W" },
};
static const struct stm32l4_rev stm32_471_revs[] = {
- { 0x1000, "1" },
+ { 0x1001, "Z" },
+};
+
+static const struct stm32l4_rev stm32_472_revs[] = {
+ { 0x1000, "A" }, { 0x2000, "B" },
+};
+
+static const struct stm32l4_rev stm32_479_revs[] = {
+ { 0x1000, "A" },
};
static const struct stm32l4_rev stm32_495_revs[] = {
{ 0x2001, "2.1" },
};
+static const struct stm32l4_rev stm32_496_revs[] = {
+ { 0x1000, "A" },
+};
+
+static const struct stm32l4_rev stm32_497_revs[] = {
+ { 0x1000, "1.0" },
+};
+
static const struct stm32l4_part_info stm32l4_parts[] = {
{
.id = 0x415,
.num_revs = ARRAY_SIZE(stm32_415_revs),
.device_str = "STM32L47/L48xx",
.max_flash_size_kb = 1024,
- .has_dual_bank = true,
+ .flags = F_HAS_DUAL_BANK,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x435,
.num_revs = ARRAY_SIZE(stm32_435_revs),
.device_str = "STM32L43/L44xx",
.max_flash_size_kb = 256,
- .has_dual_bank = false,
+ .flags = F_NONE,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x460,
+ .revs = stm32_460_revs,
+ .num_revs = ARRAY_SIZE(stm32_460_revs),
+ .device_str = "STM32G07/G08xx",
+ .max_flash_size_kb = 128,
+ .flags = F_NONE,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x461,
.num_revs = ARRAY_SIZE(stm32_461_revs),
.device_str = "STM32L49/L4Axx",
.max_flash_size_kb = 1024,
- .has_dual_bank = true,
+ .flags = F_HAS_DUAL_BANK,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x462,
.num_revs = ARRAY_SIZE(stm32_462_revs),
.device_str = "STM32L45/L46xx",
.max_flash_size_kb = 512,
- .has_dual_bank = false,
+ .flags = F_NONE,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x464,
.num_revs = ARRAY_SIZE(stm32_464_revs),
.device_str = "STM32L41/L42xx",
.max_flash_size_kb = 128,
- .has_dual_bank = false,
+ .flags = F_NONE,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x466,
+ .revs = stm32_466_revs,
+ .num_revs = ARRAY_SIZE(stm32_466_revs),
+ .device_str = "STM32G03/G04xx",
+ .max_flash_size_kb = 64,
+ .flags = F_NONE,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x467,
+ .revs = stm32_467_revs,
+ .num_revs = ARRAY_SIZE(stm32_467_revs),
+ .device_str = "STM32G0Bx/G0Cx",
+ .max_flash_size_kb = 512,
+ .flags = F_HAS_DUAL_BANK,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x468,
+ .revs = stm32_468_revs,
+ .num_revs = ARRAY_SIZE(stm32_468_revs),
+ .device_str = "STM32G43/G44xx",
+ .max_flash_size_kb = 128,
+ .flags = F_NONE,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x469,
+ .revs = stm32_469_revs,
+ .num_revs = ARRAY_SIZE(stm32_469_revs),
+ .device_str = "STM32G47/G48xx",
+ .max_flash_size_kb = 512,
+ .flags = F_HAS_DUAL_BANK | F_USE_ALL_WRPXX,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x470,
.num_revs = ARRAY_SIZE(stm32_470_revs),
.device_str = "STM32L4R/L4Sxx",
.max_flash_size_kb = 2048,
- .has_dual_bank = true,
+ .flags = F_HAS_DUAL_BANK | F_USE_ALL_WRPXX,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x471,
.num_revs = ARRAY_SIZE(stm32_471_revs),
.device_str = "STM32L4P5/L4Q5x",
.max_flash_size_kb = 1024,
- .has_dual_bank = true,
+ .flags = F_HAS_DUAL_BANK | F_USE_ALL_WRPXX,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x472,
+ .revs = stm32_472_revs,
+ .num_revs = ARRAY_SIZE(stm32_472_revs),
+ .device_str = "STM32L55/L56xx",
+ .max_flash_size_kb = 512,
+ .flags = F_HAS_DUAL_BANK | F_USE_ALL_WRPXX | F_HAS_TZ | F_HAS_L5_FLASH_REGS,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x0BFA05E0,
+ .otp_base = 0x0BFA0000,
+ .otp_size = 512,
+ },
+ {
+ .id = 0x479,
+ .revs = stm32_479_revs,
+ .num_revs = ARRAY_SIZE(stm32_479_revs),
+ .device_str = "STM32G49/G4Axx",
+ .max_flash_size_kb = 512,
+ .flags = F_NONE,
.flash_regs_base = 0x40022000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
{
.id = 0x495,
.num_revs = ARRAY_SIZE(stm32_495_revs),
.device_str = "STM32WB5x",
.max_flash_size_kb = 1024,
- .has_dual_bank = false,
+ .flags = F_NONE,
+ .flash_regs_base = 0x58004000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x496,
+ .revs = stm32_496_revs,
+ .num_revs = ARRAY_SIZE(stm32_496_revs),
+ .device_str = "STM32WB3x",
+ .max_flash_size_kb = 512,
+ .flags = F_NONE,
.flash_regs_base = 0x58004000,
.fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
+ },
+ {
+ .id = 0x497,
+ .revs = stm32_497_revs,
+ .num_revs = ARRAY_SIZE(stm32_497_revs),
+ .device_str = "STM32WLEx/WL5x",
+ .max_flash_size_kb = 256,
+ .flags = F_NONE,
+ .flash_regs_base = 0x58004000,
+ .fsize_addr = 0x1FFF75E0,
+ .otp_base = 0x1FFF7000,
+ .otp_size = 1024,
},
};
if (CMD_ARGC < 6)
return ERROR_COMMAND_SYNTAX_ERROR;
- stm32l4_info = malloc(sizeof(struct stm32l4_flash_bank));
+ /* fix-up bank base address: 0 is used for normal flash memory */
+ if (bank->base == 0)
+ bank->base = STM32_FLASH_BANK_BASE;
+
+ stm32l4_info = calloc(1, sizeof(struct stm32l4_flash_bank));
if (!stm32l4_info)
return ERROR_FAIL; /* Checkme: What better error to use?*/
bank->driver_priv = stm32l4_info;
* Ask the flash infrastructure to ensure required alignment */
bank->write_start_alignment = bank->write_end_alignment = 8;
- stm32l4_info->probed = 0;
+ stm32l4_info->probed = false;
+ stm32l4_info->otp_enabled = false;
+ stm32l4_info->user_bank_size = bank->size;
+ stm32l4_info->use_flashloader = true;
+
+ return ERROR_OK;
+}
+
+/* bitmap helper extension */
+struct range {
+ unsigned int start;
+ unsigned int end;
+};
+
+static void bitmap_to_ranges(unsigned long *bitmap, unsigned int nbits,
+ struct range *ranges, unsigned int *ranges_count) {
+ *ranges_count = 0;
+ bool last_bit = 0, cur_bit;
+ for (unsigned int i = 0; i < nbits; i++) {
+ cur_bit = test_bit(i, bitmap);
+
+ if (cur_bit && !last_bit) {
+ (*ranges_count)++;
+ ranges[*ranges_count - 1].start = i;
+ ranges[*ranges_count - 1].end = i;
+ } else if (cur_bit && last_bit) {
+ /* update (increment) the end this range */
+ ranges[*ranges_count - 1].end = i;
+ }
+
+ last_bit = cur_bit;
+ }
+}
+
+static inline int range_print_one(struct range *range, char *str)
+{
+ if (range->start == range->end)
+ return sprintf(str, "[%d]", range->start);
+
+ return sprintf(str, "[%d,%d]", range->start, range->end);
+}
+
+static char *range_print_alloc(struct range *ranges, unsigned int ranges_count)
+{
+ /* each range will be printed like the following: [start,end]
+ * start and end, both are unsigned int, an unsigned int takes 10 characters max
+ * plus 3 characters for '[', ',' and ']'
+ * thus means each range can take maximum 23 character
+ * after each range we add a ' ' as separator and finally we need the '\0'
+ * if the ranges_count is zero we reserve one char for '\0' to return an empty string */
+ char *str = calloc(1, ranges_count * (24 * sizeof(char)) + 1);
+ char *ptr = str;
+
+ for (unsigned int i = 0; i < ranges_count; i++) {
+ ptr += range_print_one(&(ranges[i]), ptr);
+
+ if (i < ranges_count - 1)
+ *(ptr++) = ' ';
+ }
+
+ return str;
+}
+
+/* end of bitmap helper extension */
+
+static inline bool stm32l4_is_otp(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return bank->base == stm32l4_info->part_info->otp_base;
+}
+
+static int stm32l4_otp_enable(struct flash_bank *bank, bool enable)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+
+ if (!stm32l4_is_otp(bank))
+ return ERROR_FAIL;
+
+ char *op_str = enable ? "enabled" : "disabled";
+
+ LOG_INFO("OTP memory (bank #%d) is %s%s for write commands",
+ bank->bank_number,
+ stm32l4_info->otp_enabled == enable ? "already " : "",
+ op_str);
+
+ stm32l4_info->otp_enabled = enable;
return ERROR_OK;
}
+static inline bool stm32l4_otp_is_enabled(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return stm32l4_info->otp_enabled;
+}
+
+static void stm32l4_sync_rdp_tzen(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+
+ bool tzen = false;
+
+ if (stm32l4_info->part_info->flags & F_HAS_TZ)
+ tzen = (stm32l4_info->optr & FLASH_TZEN) != 0;
+
+ uint32_t rdp = stm32l4_info->optr & FLASH_RDP_MASK;
+
+ /* for devices without TrustZone:
+ * RDP level 0 and 2 values are to 0xAA and 0xCC
+ * Any other value corresponds to RDP level 1
+ * for devices with TrusZone:
+ * RDP level 0 and 2 values are 0xAA and 0xCC
+ * RDP level 0.5 value is 0x55 only if TZEN = 1
+ * Any other value corresponds to RDP level 1, including 0x55 if TZEN = 0
+ */
+
+ if (rdp != RDP_LEVEL_0 && rdp != RDP_LEVEL_2) {
+ if (!tzen || (tzen && rdp != RDP_LEVEL_0_5))
+ rdp = RDP_LEVEL_1;
+ }
+
+ stm32l4_info->tzen = tzen;
+ stm32l4_info->rdp = rdp;
+}
+
static inline uint32_t stm32l4_get_flash_reg(struct flash_bank *bank, uint32_t reg_offset)
{
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
- return stm32l4_info->part_info->flash_regs_base + reg_offset;
+ return stm32l4_info->flash_regs_base + reg_offset;
+}
+
+static inline uint32_t stm32l4_get_flash_reg_by_index(struct flash_bank *bank,
+ enum stm32l4_flash_reg_index reg_index)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return stm32l4_get_flash_reg(bank, stm32l4_info->flash_regs[reg_index]);
}
static inline int stm32l4_read_flash_reg(struct flash_bank *bank, uint32_t reg_offset, uint32_t *value)
return target_read_u32(bank->target, stm32l4_get_flash_reg(bank, reg_offset), value);
}
+static inline int stm32l4_read_flash_reg_by_index(struct flash_bank *bank,
+ enum stm32l4_flash_reg_index reg_index, uint32_t *value)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return stm32l4_read_flash_reg(bank, stm32l4_info->flash_regs[reg_index], value);
+}
+
static inline int stm32l4_write_flash_reg(struct flash_bank *bank, uint32_t reg_offset, uint32_t value)
{
return target_write_u32(bank->target, stm32l4_get_flash_reg(bank, reg_offset), value);
}
+static inline int stm32l4_write_flash_reg_by_index(struct flash_bank *bank,
+ enum stm32l4_flash_reg_index reg_index, uint32_t value)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return stm32l4_write_flash_reg(bank, stm32l4_info->flash_regs[reg_index], value);
+}
+
static int stm32l4_wait_status_busy(struct flash_bank *bank, int timeout)
{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
uint32_t status;
int retval = ERROR_OK;
/* wait for busy to clear */
for (;;) {
- retval = stm32l4_read_flash_reg(bank, STM32_FLASH_SR, &status);
+ retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_SR_INDEX, &status);
if (retval != ERROR_OK)
return retval;
LOG_DEBUG("status: 0x%" PRIx32 "", status);
- if ((status & FLASH_BSY) == 0)
+ if ((status & stm32l4_info->sr_bsy_mask) == 0)
break;
if (timeout-- <= 0) {
LOG_ERROR("timed out waiting for flash");
alive_sleep(1);
}
-
if (status & FLASH_WRPERR) {
LOG_ERROR("stm32x device protected");
retval = ERROR_FAIL;
/* If this operation fails, we ignore it and report the original
* retval
*/
- stm32l4_write_flash_reg(bank, STM32_FLASH_SR, status & FLASH_ERROR);
+ stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_SR_INDEX, status & FLASH_ERROR);
}
return retval;
}
+/** set all FLASH_SECBB registers to the same value */
+static int stm32l4_set_secbb(struct flash_bank *bank, uint32_t value)
+{
+ /* This function should be used only with device with TrustZone, do just a security check */
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ assert(stm32l4_info->part_info->flags & F_HAS_TZ);
+
+ /* based on RM0438 Rev6 for STM32L5x devices:
+ * to modify a page block-based security attribution, it is recommended to
+ * 1- check that no flash operation is ongoing on the related page
+ * 2- add ISB instruction after modifying the page security attribute in SECBBxRy
+ * this step is not need in case of JTAG direct access
+ */
+ int retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* write SECBBxRy registers */
+ LOG_DEBUG("setting secure block-based areas registers (SECBBxRy) to 0x%08x", value);
+
+ const uint8_t secbb_regs[] = {
+ FLASH_SECBB1(1), FLASH_SECBB1(2), FLASH_SECBB1(3), FLASH_SECBB1(4), /* bank 1 SECBB register offsets */
+ FLASH_SECBB2(1), FLASH_SECBB2(2), FLASH_SECBB2(3), FLASH_SECBB2(4) /* bank 2 SECBB register offsets */
+ };
+
+
+ unsigned int num_secbb_regs = ARRAY_SIZE(secbb_regs);
+
+ /* in single bank mode, it's useless to modify FLASH_SECBB2Rx registers
+ * then consider only the first half of secbb_regs
+ */
+ if (!stm32l4_info->dual_bank_mode)
+ num_secbb_regs /= 2;
+
+ for (unsigned int i = 0; i < num_secbb_regs; i++) {
+ retval = stm32l4_write_flash_reg(bank, secbb_regs[i], value);
+ if (retval != ERROR_OK)
+ return retval;
+ }
+
+ return ERROR_OK;
+}
+
+static inline int stm32l4_get_flash_cr_with_lock_index(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ return (stm32l4_info->flash_regs[STM32_FLASH_CR_WLK_INDEX]) ?
+ STM32_FLASH_CR_WLK_INDEX : STM32_FLASH_CR_INDEX;
+}
+
static int stm32l4_unlock_reg(struct flash_bank *bank)
{
+ const uint32_t flash_cr_index = stm32l4_get_flash_cr_with_lock_index(bank);
uint32_t ctrl;
/* first check if not already unlocked
* otherwise writing on STM32_FLASH_KEYR will fail
*/
- int retval = stm32l4_read_flash_reg(bank, STM32_FLASH_CR, &ctrl);
+ int retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
return ERROR_OK;
/* unlock flash registers */
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_KEYR, KEY1);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_KEYR_INDEX, KEY1);
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_KEYR, KEY2);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_KEYR_INDEX, KEY2);
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_read_flash_reg(bank, STM32_FLASH_CR, &ctrl);
+ retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
static int stm32l4_unlock_option_reg(struct flash_bank *bank)
{
+ const uint32_t flash_cr_index = stm32l4_get_flash_cr_with_lock_index(bank);
uint32_t ctrl;
- int retval = stm32l4_read_flash_reg(bank, STM32_FLASH_CR, &ctrl);
+ int retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
return ERROR_OK;
/* unlock option registers */
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_OPTKEYR, OPTKEY1);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_OPTKEYR_INDEX, OPTKEY1);
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_OPTKEYR, OPTKEY2);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_OPTKEYR_INDEX, OPTKEY2);
if (retval != ERROR_OK)
return retval;
- retval = stm32l4_read_flash_reg(bank, STM32_FLASH_CR, &ctrl);
+ retval = stm32l4_read_flash_reg_by_index(bank, flash_cr_index, &ctrl);
if (retval != ERROR_OK)
return retval;
return ERROR_OK;
}
-static int stm32l4_write_option(struct flash_bank *bank, uint32_t reg_offset, uint32_t value, uint32_t mask)
+static int stm32l4_perform_obl_launch(struct flash_bank *bank)
+{
+ int retval, retval2;
+
+ retval = stm32l4_unlock_reg(bank);
+ if (retval != ERROR_OK)
+ goto err_lock;
+
+ retval = stm32l4_unlock_option_reg(bank);
+ if (retval != ERROR_OK)
+ goto err_lock;
+
+ /* Set OBL_LAUNCH bit in CR -> system reset and option bytes reload,
+ * but the RMs explicitly do *NOT* list this as power-on reset cause, and:
+ * "Note: If the read protection is set while the debugger is still
+ * connected through JTAG/SWD, apply a POR (power-on reset) instead of a system reset."
+ */
+
+ /* "Setting OBL_LAUNCH generates a reset so the option byte loading is performed under system reset" */
+ /* Due to this reset ST-Link reports an SWD_DP_ERROR, despite the write was successful,
+ * then just ignore the returned value */
+ stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_OBL_LAUNCH);
+
+ /* Need to re-probe after change */
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ stm32l4_info->probed = false;
+
+err_lock:
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank),
+ FLASH_LOCK | FLASH_OPTLOCK);
+
+ if (retval != ERROR_OK)
+ return retval;
+
+ return retval2;
+}
+
+static int stm32l4_write_option(struct flash_bank *bank, uint32_t reg_offset,
+ uint32_t value, uint32_t mask)
{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
uint32_t optiondata;
+ int retval, retval2;
- int retval = stm32l4_read_flash_reg(bank, reg_offset, &optiondata);
+ retval = stm32l4_read_flash_reg(bank, reg_offset, &optiondata);
if (retval != ERROR_OK)
return retval;
+ /* for STM32L5 and similar devices, use always non-secure
+ * registers for option bytes programming */
+ const uint32_t *saved_flash_regs = stm32l4_info->flash_regs;
+ if (stm32l4_info->part_info->flags & F_HAS_L5_FLASH_REGS)
+ stm32l4_info->flash_regs = stm32l5_ns_flash_regs;
+
retval = stm32l4_unlock_reg(bank);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
retval = stm32l4_unlock_option_reg(bank);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
optiondata = (optiondata & ~mask) | (value & mask);
retval = stm32l4_write_flash_reg(bank, reg_offset, optiondata);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, FLASH_OPTSTRT);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_OPTSTRT);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
+
+err_lock:
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank),
+ FLASH_LOCK | FLASH_OPTLOCK);
+ stm32l4_info->flash_regs = saved_flash_regs;
+
if (retval != ERROR_OK)
return retval;
- return retval;
+ return retval2;
}
-static int stm32l4_protect_check(struct flash_bank *bank)
+static int stm32l4_get_one_wrpxy(struct flash_bank *bank, struct stm32l4_wrp *wrpxy,
+ enum stm32l4_flash_reg_index reg_idx, int offset)
{
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ int ret;
- uint32_t wrp1ar, wrp1br, wrp2ar, wrp2br;
- stm32l4_read_flash_reg(bank, STM32_FLASH_WRP1AR, &wrp1ar);
- stm32l4_read_flash_reg(bank, STM32_FLASH_WRP1BR, &wrp1br);
- stm32l4_read_flash_reg(bank, STM32_FLASH_WRP2AR, &wrp2ar);
- stm32l4_read_flash_reg(bank, STM32_FLASH_WRP2BR, &wrp2br);
-
- const uint8_t wrp1a_start = wrp1ar & 0xFF;
- const uint8_t wrp1a_end = (wrp1ar >> 16) & 0xFF;
- const uint8_t wrp1b_start = wrp1br & 0xFF;
- const uint8_t wrp1b_end = (wrp1br >> 16) & 0xFF;
- const uint8_t wrp2a_start = wrp2ar & 0xFF;
- const uint8_t wrp2a_end = (wrp2ar >> 16) & 0xFF;
- const uint8_t wrp2b_start = wrp2br & 0xFF;
- const uint8_t wrp2b_end = (wrp2br >> 16) & 0xFF;
-
- for (int i = 0; i < bank->num_sectors; i++) {
- if (i < stm32l4_info->bank1_sectors) {
- if (((i >= wrp1a_start) &&
- (i <= wrp1a_end)) ||
- ((i >= wrp1b_start) &&
- (i <= wrp1b_end)))
- bank->sectors[i].is_protected = 1;
- else
- bank->sectors[i].is_protected = 0;
- } else {
- uint8_t snb;
- snb = i - stm32l4_info->bank1_sectors;
- if (((snb >= wrp2a_start) &&
- (snb <= wrp2a_end)) ||
- ((snb >= wrp2b_start) &&
- (snb <= wrp2b_end)))
- bank->sectors[i].is_protected = 1;
- else
- bank->sectors[i].is_protected = 0;
+ wrpxy->reg_idx = reg_idx;
+ wrpxy->offset = offset;
+
+ ret = stm32l4_read_flash_reg_by_index(bank, wrpxy->reg_idx , &wrpxy->value);
+ if (ret != ERROR_OK)
+ return ret;
+
+ wrpxy->first = (wrpxy->value & stm32l4_info->wrpxxr_mask) + wrpxy->offset;
+ wrpxy->last = ((wrpxy->value >> 16) & stm32l4_info->wrpxxr_mask) + wrpxy->offset;
+ wrpxy->used = wrpxy->first <= wrpxy->last;
+
+ return ERROR_OK;
+}
+
+static int stm32l4_get_all_wrpxy(struct flash_bank *bank, enum stm32_bank_id dev_bank_id,
+ struct stm32l4_wrp *wrpxy, unsigned int *n_wrp)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ int ret;
+
+ *n_wrp = 0;
+
+ /* for single bank devices there is 2 WRP regions.
+ * for dual bank devices there is 2 WRP regions per bank,
+ * if configured as single bank only 2 WRP are usable
+ * except for STM32L4R/S/P/Q, G4 cat3, L5 ... all 4 WRP are usable
+ * note: this should be revised, if a device will have the SWAP banks option
+ */
+
+ int wrp2y_sectors_offset = -1; /* -1 : unused */
+
+ /* if bank_id is BANK1 or ALL_BANKS */
+ if (dev_bank_id != STM32_BANK2) {
+ /* get FLASH_WRP1AR */
+ ret = stm32l4_get_one_wrpxy(bank, &wrpxy[(*n_wrp)++], STM32_FLASH_WRP1AR_INDEX, 0);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* get WRP1BR */
+ ret = stm32l4_get_one_wrpxy(bank, &wrpxy[(*n_wrp)++], STM32_FLASH_WRP1BR_INDEX, 0);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* for some devices (like STM32L4R/S) in single-bank mode, the 4 WRPxx are usable */
+ if ((stm32l4_info->part_info->flags & F_USE_ALL_WRPXX) && !stm32l4_info->dual_bank_mode)
+ wrp2y_sectors_offset = 0;
+ }
+
+ /* if bank_id is BANK2 or ALL_BANKS */
+ if (dev_bank_id != STM32_BANK1 && stm32l4_info->dual_bank_mode)
+ wrp2y_sectors_offset = stm32l4_info->bank1_sectors;
+
+ if (wrp2y_sectors_offset > -1) {
+ /* get WRP2AR */
+ ret = stm32l4_get_one_wrpxy(bank, &wrpxy[(*n_wrp)++], STM32_FLASH_WRP2AR_INDEX, wrp2y_sectors_offset);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* get WRP2BR */
+ ret = stm32l4_get_one_wrpxy(bank, &wrpxy[(*n_wrp)++], STM32_FLASH_WRP2BR_INDEX, wrp2y_sectors_offset);
+ if (ret != ERROR_OK)
+ return ret;
+ }
+
+ return ERROR_OK;
+}
+
+static int stm32l4_write_one_wrpxy(struct flash_bank *bank, struct stm32l4_wrp *wrpxy)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+
+ int wrp_start = wrpxy->first - wrpxy->offset;
+ int wrp_end = wrpxy->last - wrpxy->offset;
+
+ uint32_t wrp_value = (wrp_start & stm32l4_info->wrpxxr_mask) | ((wrp_end & stm32l4_info->wrpxxr_mask) << 16);
+
+ return stm32l4_write_option(bank, stm32l4_info->flash_regs[wrpxy->reg_idx], wrp_value, 0xffffffff);
+}
+
+static int stm32l4_write_all_wrpxy(struct flash_bank *bank, struct stm32l4_wrp *wrpxy, unsigned int n_wrp)
+{
+ int ret;
+
+ for (unsigned int i = 0; i < n_wrp; i++) {
+ ret = stm32l4_write_one_wrpxy(bank, &wrpxy[i]);
+ if (ret != ERROR_OK)
+ return ret;
+ }
+
+ return ERROR_OK;
+}
+
+static int stm32l4_protect_check(struct flash_bank *bank)
+{
+ unsigned int n_wrp;
+ struct stm32l4_wrp wrpxy[4];
+
+ int ret = stm32l4_get_all_wrpxy(bank, STM32_ALL_BANKS, wrpxy, &n_wrp);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* initialize all sectors as unprotected */
+ for (unsigned int i = 0; i < bank->num_sectors; i++)
+ bank->sectors[i].is_protected = 0;
+
+ /* now check WRPxy and mark the protected sectors */
+ for (unsigned int i = 0; i < n_wrp; i++) {
+ if (wrpxy[i].used) {
+ for (int s = wrpxy[i].first; s <= wrpxy[i].last; s++)
+ bank->sectors[s].is_protected = 1;
}
}
+
return ERROR_OK;
}
-static int stm32l4_erase(struct flash_bank *bank, int first, int last)
+static int stm32l4_erase(struct flash_bank *bank, unsigned int first,
+ unsigned int last)
{
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
- int i;
- int retval;
+ int retval, retval2;
+
+ assert((first <= last) && (last < bank->num_sectors));
- assert(first < bank->num_sectors);
- assert(last < bank->num_sectors);
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("cannot erase OTP memory");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
if (bank->target->state != TARGET_HALTED) {
LOG_ERROR("Target not halted");
return ERROR_TARGET_NOT_HALTED;
}
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* set all FLASH pages as secure */
+ retval = stm32l4_set_secbb(bank, FLASH_SECBB_SECURE);
+ if (retval != ERROR_OK) {
+ /* restore all FLASH pages as non-secure */
+ stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE); /* ignore the return value */
+ return retval;
+ }
+ }
+
retval = stm32l4_unlock_reg(bank);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
/*
Sector Erase
To erase a sector, follow the procedure below:
1. Check that no Flash memory operation is ongoing by
- checking the BSY bit in the FLASH_SR register
+ checking the BSY bit in the FLASH_SR register
2. Set the PER bit and select the page and bank
you wish to erase in the FLASH_CR register
3. Set the STRT bit in the FLASH_CR register
4. Wait for the BSY bit to be cleared
*/
- for (i = first; i <= last; i++) {
+ for (unsigned int i = first; i <= last; i++) {
uint32_t erase_flags;
erase_flags = FLASH_PER | FLASH_STRT;
if (i >= stm32l4_info->bank1_sectors) {
uint8_t snb;
snb = i - stm32l4_info->bank1_sectors;
- erase_flags |= snb << FLASH_PAGE_SHIFT | FLASH_CR_BKER;
+ erase_flags |= snb << FLASH_PAGE_SHIFT | stm32l4_info->cr_bker_mask;
} else
erase_flags |= i << FLASH_PAGE_SHIFT;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, erase_flags);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, erase_flags);
if (retval != ERROR_OK)
- return retval;
+ break;
retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
if (retval != ERROR_OK)
- return retval;
+ break;
+ }
+
+err_lock:
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
- bank->sectors[i].is_erased = 1;
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* restore all FLASH pages as non-secure */
+ int retval3 = stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE);
+ if (retval3 != ERROR_OK)
+ return retval3;
}
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, FLASH_LOCK);
if (retval != ERROR_OK)
return retval;
- return ERROR_OK;
+ return retval2;
}
-static int stm32l4_protect(struct flash_bank *bank, int set, int first, int last)
+static int stm32l4_protect(struct flash_bank *bank, int set, unsigned int first, unsigned int last)
{
struct target *target = bank->target;
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ int ret = ERROR_OK;
+ unsigned int i;
+
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("cannot protect/unprotect OTP memory");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
if (target->state != TARGET_HALTED) {
LOG_ERROR("Target not halted");
return ERROR_TARGET_NOT_HALTED;
}
- int ret = ERROR_OK;
- /* Bank 2 */
- uint32_t reg_value = 0xFF; /* Default to bank un-protected */
+ /* the requested sectors could be located into bank1 and/or bank2 */
+ bool use_bank2 = false;
if (last >= stm32l4_info->bank1_sectors) {
- if (set == 1) {
- uint8_t begin = first > stm32l4_info->bank1_sectors ? first : 0x00;
- reg_value = ((last & 0xFF) << 16) | begin;
+ if (first < stm32l4_info->bank1_sectors) {
+ /* the requested sectors for (un)protection are shared between
+ * bank 1 and 2, then split the operation */
+
+ /* 1- deal with bank 1 sectors */
+ LOG_DEBUG("The requested sectors for %s are shared between bank 1 and 2",
+ set ? "protection" : "unprotection");
+ ret = stm32l4_protect(bank, set, first, stm32l4_info->bank1_sectors - 1);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* 2- then continue with bank 2 sectors */
+ first = stm32l4_info->bank1_sectors;
}
- ret = stm32l4_write_option(bank, STM32_FLASH_WRP2AR, reg_value, 0xffffffff);
+ use_bank2 = true;
}
- /* Bank 1 */
- reg_value = 0xFF; /* Default to bank un-protected */
- if (first < stm32l4_info->bank1_sectors) {
- if (set == 1) {
- uint8_t end = last >= stm32l4_info->bank1_sectors ? 0xFF : last;
- reg_value = (end << 16) | (first & 0xFF);
+
+ /* refresh the sectors' protection */
+ ret = stm32l4_protect_check(bank);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* check if the desired protection is already configured */
+ for (i = first; i <= last; i++) {
+ if (bank->sectors[i].is_protected != set)
+ break;
+ else if (i == last) {
+ LOG_INFO("The specified sectors are already %s", set ? "protected" : "unprotected");
+ return ERROR_OK;
}
+ }
+
+ /* all sectors from first to last (or part of them) could have different
+ * protection other than the requested */
+ unsigned int n_wrp;
+ struct stm32l4_wrp wrpxy[4];
+
+ ret = stm32l4_get_all_wrpxy(bank, use_bank2 ? STM32_BANK2 : STM32_BANK1, wrpxy, &n_wrp);
+ if (ret != ERROR_OK)
+ return ret;
- ret = stm32l4_write_option(bank, STM32_FLASH_WRP1AR, reg_value, 0xffffffff);
+ /* use bitmap and range helpers to optimize the WRP usage */
+ DECLARE_BITMAP(pages, bank->num_sectors);
+ bitmap_zero(pages, bank->num_sectors);
+
+ for (i = 0; i < n_wrp; i++) {
+ if (wrpxy[i].used) {
+ for (int p = wrpxy[i].first; p <= wrpxy[i].last; p++)
+ set_bit(p, pages);
+ }
+ }
+
+ /* we have at most 'n_wrp' WRP areas
+ * add one range if the user is trying to protect a fifth range */
+ struct range ranges[n_wrp + 1];
+ unsigned int ranges_count = 0;
+
+ bitmap_to_ranges(pages, bank->num_sectors, ranges, &ranges_count);
+
+ /* pretty-print the currently protected ranges */
+ if (ranges_count > 0) {
+ char *ranges_str = range_print_alloc(ranges, ranges_count);
+ LOG_DEBUG("current protected areas: %s", ranges_str);
+ free(ranges_str);
+ } else
+ LOG_DEBUG("current protected areas: none");
+
+ if (set) { /* flash protect */
+ for (i = first; i <= last; i++)
+ set_bit(i, pages);
+ } else { /* flash unprotect */
+ for (i = first; i <= last; i++)
+ clear_bit(i, pages);
+ }
+
+ /* check the ranges_count after the user request */
+ bitmap_to_ranges(pages, bank->num_sectors, ranges, &ranges_count);
+
+ /* pretty-print the requested areas for protection */
+ if (ranges_count > 0) {
+ char *ranges_str = range_print_alloc(ranges, ranges_count);
+ LOG_DEBUG("requested areas for protection: %s", ranges_str);
+ free(ranges_str);
+ } else
+ LOG_DEBUG("requested areas for protection: none");
+
+ if (ranges_count > n_wrp) {
+ LOG_ERROR("cannot set the requested protection "
+ "(only %u write protection areas are available)" , n_wrp);
+ return ERROR_FAIL;
+ }
+
+ /* re-init all WRPxy as disabled (first > last)*/
+ for (i = 0; i < n_wrp; i++) {
+ wrpxy[i].first = wrpxy[i].offset + 1;
+ wrpxy[i].last = wrpxy[i].offset;
+ }
+
+ /* then configure WRPxy areas */
+ for (i = 0; i < ranges_count; i++) {
+ wrpxy[i].first = ranges[i].start;
+ wrpxy[i].last = ranges[i].end;
}
- return ret;
+ /* finally write WRPxy registers */
+ return stm32l4_write_all_wrpxy(bank, wrpxy, n_wrp);
}
-/* Count is in halfwords */
+/* Count is in double-words */
static int stm32l4_write_block(struct flash_bank *bank, const uint8_t *buffer,
- uint32_t offset, uint32_t count)
+ uint32_t offset, uint32_t count)
{
struct target *target = bank->target;
- struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
- uint32_t buffer_size = 16384;
+ uint32_t buffer_size;
struct working_area *write_algorithm;
struct working_area *source;
uint32_t address = bank->base + offset;
- struct reg_param reg_params[5];
+ struct reg_param reg_params[6];
struct armv7m_algorithm armv7m_info;
int retval = ERROR_OK;
return retval;
}
- /* memory buffer */
- while (target_alloc_working_area_try(target, buffer_size, &source) !=
- ERROR_OK) {
- buffer_size /= 2;
- if (buffer_size <= 256) {
- /* we already allocated the writing code, but failed to get a
- * buffer, free the algorithm */
- target_free_working_area(target, write_algorithm);
+ /* memory buffer, size *must* be multiple of dword plus one dword for rp and one for wp */
+ buffer_size = target_get_working_area_avail(target) & ~(2 * sizeof(uint32_t) - 1);
+ if (buffer_size < 256) {
+ LOG_WARNING("large enough working area not available, can't do block memory writes");
+ return ERROR_TARGET_RESOURCE_NOT_AVAILABLE;
+ } else if (buffer_size > 16384) {
+ /* probably won't benefit from more than 16k ... */
+ buffer_size = 16384;
+ }
- LOG_WARNING("large enough working area not available, can't do block memory writes");
- return ERROR_TARGET_RESOURCE_NOT_AVAILABLE;
- }
+ if (target_alloc_working_area_try(target, buffer_size, &source) != ERROR_OK) {
+ LOG_ERROR("allocating working area failed");
+ return ERROR_TARGET_RESOURCE_NOT_AVAILABLE;
}
armv7m_info.common_magic = ARMV7M_COMMON_MAGIC;
init_reg_param(®_params[1], "r1", 32, PARAM_OUT); /* buffer end */
init_reg_param(®_params[2], "r2", 32, PARAM_OUT); /* target address */
init_reg_param(®_params[3], "r3", 32, PARAM_OUT); /* count (double word-64bit) */
- init_reg_param(®_params[4], "r4", 32, PARAM_OUT); /* flash base */
+ init_reg_param(®_params[4], "r4", 32, PARAM_OUT); /* flash status register */
+ init_reg_param(®_params[5], "r5", 32, PARAM_OUT); /* flash control register */
buf_set_u32(reg_params[0].value, 0, 32, source->address);
buf_set_u32(reg_params[1].value, 0, 32, source->address + source->size);
buf_set_u32(reg_params[2].value, 0, 32, address);
- buf_set_u32(reg_params[3].value, 0, 32, count / 4);
- buf_set_u32(reg_params[4].value, 0, 32, stm32l4_info->part_info->flash_regs_base);
+ buf_set_u32(reg_params[3].value, 0, 32, count);
+ buf_set_u32(reg_params[4].value, 0, 32, stm32l4_get_flash_reg_by_index(bank, STM32_FLASH_SR_INDEX));
+ buf_set_u32(reg_params[5].value, 0, 32, stm32l4_get_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX));
- retval = target_run_flash_async_algorithm(target, buffer, count, 2,
+ retval = target_run_flash_async_algorithm(target, buffer, count, 8,
0, NULL,
- 5, reg_params,
+ ARRAY_SIZE(reg_params), reg_params,
source->address, source->size,
write_algorithm->address, 0,
&armv7m_info);
if (error != 0) {
LOG_ERROR("flash write failed = %08" PRIx32, error);
/* Clear but report errors */
- stm32l4_write_flash_reg(bank, STM32_FLASH_SR, error);
+ stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_SR_INDEX, error);
retval = ERROR_FAIL;
}
}
destroy_reg_param(®_params[2]);
destroy_reg_param(®_params[3]);
destroy_reg_param(®_params[4]);
+ destroy_reg_param(®_params[5]);
+
+ return retval;
+}
+
+/* Count is in double-words */
+static int stm32l4_write_block_without_loader(struct flash_bank *bank, const uint8_t *buffer,
+ uint32_t offset, uint32_t count)
+{
+ struct target *target = bank->target;
+ uint32_t address = bank->base + offset;
+ int retval = ERROR_OK;
+
+ /* wait for BSY bit */
+ retval = stm32l4_wait_status_busy(bank, FLASH_WRITE_TIMEOUT);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* set PG in FLASH_CR */
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, FLASH_PG);
+ if (retval != ERROR_OK)
+ return retval;
+
+
+ /* write directly to flash memory */
+ const uint8_t *src = buffer;
+ while (count--) {
+ retval = target_write_memory(target, address, 4, 2, src);
+ if (retval != ERROR_OK)
+ return retval;
+
+ /* wait for BSY bit */
+ retval = stm32l4_wait_status_busy(bank, FLASH_WRITE_TIMEOUT);
+ if (retval != ERROR_OK)
+ return retval;
+
+ src += 8;
+ address += 8;
+ }
+
+ /* reset PG in FLASH_CR */
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, 0);
+ if (retval != ERROR_OK)
+ return retval;
+
+ return retval;
+}
+
+static int stm32l4_write(struct flash_bank *bank, const uint8_t *buffer,
+ uint32_t offset, uint32_t count)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ int retval = ERROR_OK, retval2;
+
+ if (stm32l4_is_otp(bank) && !stm32l4_otp_is_enabled(bank)) {
+ LOG_ERROR("OTP memory is disabled for write commands");
+ return ERROR_FAIL;
+ }
+
+ if (bank->target->state != TARGET_HALTED) {
+ LOG_ERROR("Target not halted");
+ return ERROR_TARGET_NOT_HALTED;
+ }
+
+ /* The flash write must be aligned to a double word (8-bytes) boundary.
+ * The flash infrastructure ensures it, do just a security check */
+ assert(offset % 8 == 0);
+ assert(count % 8 == 0);
+
+ /* STM32G4xxx Cat. 3 devices may have gaps between banks, check whether
+ * data to be written does not go into a gap:
+ * suppose buffer is fully contained in bank from sector 0 to sector
+ * num->sectors - 1 and sectors are ordered according to offset
+ */
+ struct flash_sector *head = &bank->sectors[0];
+ struct flash_sector *tail = &bank->sectors[bank->num_sectors - 1];
+
+ while ((head < tail) && (offset >= (head + 1)->offset)) {
+ /* buffer does not intersect head nor gap behind head */
+ head++;
+ }
+
+ while ((head < tail) && (offset + count <= (tail - 1)->offset + (tail - 1)->size)) {
+ /* buffer does not intersect tail nor gap before tail */
+ --tail;
+ }
+
+ LOG_DEBUG("data: 0x%08" PRIx32 " - 0x%08" PRIx32 ", sectors: 0x%08" PRIx32 " - 0x%08" PRIx32,
+ offset, offset + count - 1, head->offset, tail->offset + tail->size - 1);
+
+ /* Now check that there is no gap from head to tail, this should work
+ * even for multiple or non-symmetric gaps
+ */
+ while (head < tail) {
+ if (head->offset + head->size != (head + 1)->offset) {
+ LOG_ERROR("write into gap from " TARGET_ADDR_FMT " to " TARGET_ADDR_FMT,
+ bank->base + head->offset + head->size,
+ bank->base + (head + 1)->offset - 1);
+ retval = ERROR_FLASH_DST_OUT_OF_BANK;
+ }
+ head++;
+ }
+
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* set all FLASH pages as secure */
+ retval = stm32l4_set_secbb(bank, FLASH_SECBB_SECURE);
+ if (retval != ERROR_OK) {
+ /* restore all FLASH pages as non-secure */
+ stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE); /* ignore the return value */
+ return retval;
+ }
+ }
+
+ retval = stm32l4_unlock_reg(bank);
+ if (retval != ERROR_OK)
+ goto err_lock;
+
+ /**
+ * FIXME update the flash loader to use a custom FLASH_SR_BSY mask
+ * Workaround for STM32G0Bx/G0Cx devices in dual bank mode,
+ * as the flash loader does not use the SR_BSY2
+ */
+ bool use_flashloader = stm32l4_info->use_flashloader;
+ if ((stm32l4_info->part_info->id == 0x467) && stm32l4_info->dual_bank_mode) {
+ LOG_INFO("Couldn't use the flash loader in dual-bank mode");
+ use_flashloader = false;
+ }
+
+ if (use_flashloader) {
+ /* For TrustZone enabled devices, when TZEN is set and RDP level is 0.5,
+ * the debug is possible only in non-secure state.
+ * Thus means the flashloader will run in non-secure mode,
+ * and the workarea need to be in non-secure RAM */
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0_5))
+ LOG_INFO("RDP level is 0.5, the work-area should reside in non-secure RAM");
+
+ retval = stm32l4_write_block(bank, buffer, offset, count / 8);
+ }
+
+ if (!use_flashloader || retval == ERROR_TARGET_RESOURCE_NOT_AVAILABLE) {
+ LOG_INFO("falling back to single memory accesses");
+ retval = stm32l4_write_block_without_loader(bank, buffer, offset, count / 8);
+ }
+
+
+err_lock:
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
+
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* restore all FLASH pages as non-secure */
+ int retval3 = stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE);
+ if (retval3 != ERROR_OK)
+ return retval3;
+ }
- return retval;
+ if (retval != ERROR_OK) {
+ LOG_ERROR("block write failed");
+ return retval;
+ }
+ return retval2;
}
-static int stm32l4_write(struct flash_bank *bank, const uint8_t *buffer,
- uint32_t offset, uint32_t count)
+static int stm32l4_read_idcode(struct flash_bank *bank, uint32_t *id)
{
int retval;
- if (bank->target->state != TARGET_HALTED) {
- LOG_ERROR("Target not halted");
- return ERROR_TARGET_NOT_HALTED;
+ /* try reading possible IDCODE registers, in the following order */
+ uint32_t dbgmcu_idcode[] = {DBGMCU_IDCODE_L4_G4, DBGMCU_IDCODE_G0, DBGMCU_IDCODE_L5};
+
+ for (unsigned int i = 0; i < ARRAY_SIZE(dbgmcu_idcode); i++) {
+ retval = target_read_u32(bank->target, dbgmcu_idcode[i], id);
+ if ((retval == ERROR_OK) && ((*id & 0xfff) != 0) && ((*id & 0xfff) != 0xfff))
+ return ERROR_OK;
}
- /* The flash write must be aligned to a double word (8-bytes) boundary.
- * The flash infrastructure ensures it, do just a security check */
- assert(offset % 8 == 0);
- assert(count % 8 == 0);
+ /* Workaround for STM32WL5x devices:
+ * DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
+ * to solve this read the UID64 (IEEE 64-bit unique device ID register) */
- retval = stm32l4_unlock_reg(bank);
- if (retval != ERROR_OK)
- return retval;
+ struct cortex_m_common *cortex_m = target_to_cm(bank->target);
- retval = stm32l4_write_block(bank, buffer, offset, count / 2);
- if (retval != ERROR_OK) {
- LOG_WARNING("block write failed");
- return retval;
+ if (cortex_m->core_info->partno == CORTEX_M0P_PARTNO && cortex_m->armv7m.debug_ap->ap_num == 1) {
+ uint32_t uid64_ids;
+
+ /* UID64 is contains
+ * - Bits 63:32 : DEVNUM (unique device number, different for each individual device)
+ * - Bits 31:08 : STID (company ID) = 0x0080E1
+ * - Bits 07:00 : DEVID (device ID) = 0x15
+ *
+ * read only the fixed values {STID,DEVID} from UID64_IDS to identify the device as STM32WLx
+ */
+ retval = target_read_u32(bank->target, UID64_IDS, &uid64_ids);
+ if (retval == ERROR_OK && uid64_ids == UID64_IDS_STM32WL) {
+ /* force the DEV_ID to 0x497 and the REV_ID to unknown */
+ *id = 0x00000497;
+ return ERROR_OK;
+ }
}
- LOG_WARNING("block write succeeded");
- return stm32l4_write_flash_reg(bank, STM32_FLASH_CR, FLASH_LOCK);
+ LOG_ERROR("can't get the device id");
+ return (retval == ERROR_OK) ? ERROR_FAIL : retval;
}
-static int stm32l4_read_idcode(struct flash_bank *bank, uint32_t *id)
+static const char *get_stm32l4_rev_str(struct flash_bank *bank)
{
- int retval = target_read_u32(bank->target, DBGMCU_IDCODE, id);
- if (retval != ERROR_OK)
- return retval;
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ const struct stm32l4_part_info *part_info = stm32l4_info->part_info;
+ assert(part_info);
- return retval;
+ const uint16_t rev_id = stm32l4_info->idcode >> 16;
+ for (unsigned int i = 0; i < part_info->num_revs; i++) {
+ if (rev_id == part_info->revs[i].rev)
+ return part_info->revs[i].str;
+ }
+ return "'unknown'";
+}
+
+static const char *get_stm32l4_bank_type_str(struct flash_bank *bank)
+{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ assert(stm32l4_info->part_info);
+ return stm32l4_is_otp(bank) ? "OTP" :
+ stm32l4_info->dual_bank_mode ? "Flash dual" :
+ "Flash single";
}
static int stm32l4_probe(struct flash_bank *bank)
{
struct target *target = bank->target;
+ struct armv7m_common *armv7m = target_to_armv7m(target);
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
const struct stm32l4_part_info *part_info;
- int i;
- uint16_t flash_size_in_kb = 0xffff;
- uint32_t device_id;
- uint32_t options;
+ uint16_t flash_size_kb = 0xffff;
- stm32l4_info->probed = 0;
+ stm32l4_info->probed = false;
- /* read stm32 device id register */
+ /* read stm32 device id registers */
int retval = stm32l4_read_idcode(bank, &stm32l4_info->idcode);
if (retval != ERROR_OK)
return retval;
- device_id = stm32l4_info->idcode & 0xFFF;
+ const uint32_t device_id = stm32l4_info->idcode & 0xFFF;
for (unsigned int n = 0; n < ARRAY_SIZE(stm32l4_parts); n++) {
- if (device_id == stm32l4_parts[n].id)
+ if (device_id == stm32l4_parts[n].id) {
stm32l4_info->part_info = &stm32l4_parts[n];
+ break;
+ }
}
if (!stm32l4_info->part_info) {
- LOG_WARNING("Cannot identify target as an STM32 L4 or WB family device.");
+ LOG_WARNING("Cannot identify target as an %s family device.", device_families);
return ERROR_FAIL;
}
part_info = stm32l4_info->part_info;
+ const char *rev_str = get_stm32l4_rev_str(bank);
+ const uint16_t rev_id = stm32l4_info->idcode >> 16;
- char device_info[1024];
- retval = bank->driver->info(bank, device_info, sizeof(device_info));
+ LOG_INFO("device idcode = 0x%08" PRIx32 " (%s - Rev %s : 0x%04x)",
+ stm32l4_info->idcode, part_info->device_str, rev_str, rev_id);
+
+ stm32l4_info->flash_regs_base = stm32l4_info->part_info->flash_regs_base;
+ stm32l4_info->cr_bker_mask = FLASH_BKER;
+ stm32l4_info->sr_bsy_mask = FLASH_BSY;
+
+ /* initialise the flash registers layout */
+ if (part_info->flags & F_HAS_L5_FLASH_REGS)
+ stm32l4_info->flash_regs = stm32l5_ns_flash_regs;
+ else
+ stm32l4_info->flash_regs = stm32l4_flash_regs;
+
+ /* read flash option register */
+ retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_OPTR_INDEX, &stm32l4_info->optr);
if (retval != ERROR_OK)
return retval;
- LOG_INFO("device idcode = 0x%08" PRIx32 " (%s)", stm32l4_info->idcode, device_info);
+ stm32l4_sync_rdp_tzen(bank);
+
+ /* for devices with trustzone, use flash secure registers when TZEN=1 and RDP is LEVEL_0 */
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ if (part_info->flags & F_HAS_L5_FLASH_REGS) {
+ stm32l4_info->flash_regs_base |= STM32L5_REGS_SEC_OFFSET;
+ stm32l4_info->flash_regs = stm32l5_s_flash_regs;
+ } else {
+ LOG_ERROR("BUG: device supported incomplete");
+ return ERROR_NOT_IMPLEMENTED;
+ }
+ }
+
+ if (part_info->flags & F_HAS_TZ)
+ LOG_INFO("TZEN = %d : TrustZone %s by option bytes",
+ stm32l4_info->tzen,
+ stm32l4_info->tzen ? "enabled" : "disabled");
+
+ LOG_INFO("RDP level %s (0x%02X)",
+ stm32l4_info->rdp == RDP_LEVEL_0 ? "0" : stm32l4_info->rdp == RDP_LEVEL_0_5 ? "0.5" : "1",
+ stm32l4_info->rdp);
+
+ if (stm32l4_is_otp(bank)) {
+ bank->size = part_info->otp_size;
+
+ LOG_INFO("OTP size is %d bytes, base address is " TARGET_ADDR_FMT, bank->size, bank->base);
+
+ /* OTP memory is considered as one sector */
+ free(bank->sectors);
+ bank->num_sectors = 1;
+ bank->sectors = alloc_block_array(0, part_info->otp_size, 1);
+
+ if (!bank->sectors) {
+ LOG_ERROR("failed to allocate bank sectors");
+ return ERROR_FAIL;
+ }
+
+ stm32l4_info->probed = true;
+ return ERROR_OK;
+ } else if (bank->base != STM32_FLASH_BANK_BASE && bank->base != STM32_FLASH_S_BANK_BASE) {
+ LOG_ERROR("invalid bank base address");
+ return ERROR_FAIL;
+ }
/* get flash size from target. */
- retval = target_read_u16(target, part_info->fsize_addr, &flash_size_in_kb);
+ retval = target_read_u16(target, part_info->fsize_addr, &flash_size_kb);
/* failed reading flash size or flash size invalid (early silicon),
* default to max target family */
- if (retval != ERROR_OK || flash_size_in_kb == 0xffff || flash_size_in_kb == 0
- || flash_size_in_kb > part_info->max_flash_size_kb) {
+ if (retval != ERROR_OK || flash_size_kb == 0xffff || flash_size_kb == 0
+ || flash_size_kb > part_info->max_flash_size_kb) {
LOG_WARNING("STM32 flash size failed, probe inaccurate - assuming %dk flash",
part_info->max_flash_size_kb);
- flash_size_in_kb = part_info->max_flash_size_kb;
+ flash_size_kb = part_info->max_flash_size_kb;
}
- LOG_INFO("flash size = %dkbytes", flash_size_in_kb);
+ /* if the user sets the size manually then ignore the probed value
+ * this allows us to work around devices that have a invalid flash size register value */
+ if (stm32l4_info->user_bank_size) {
+ LOG_WARNING("overriding size register by configured bank size - MAY CAUSE TROUBLE");
+ flash_size_kb = stm32l4_info->user_bank_size / 1024;
+ }
- /* did we assign a flash size? */
- assert((flash_size_in_kb != 0xffff) && flash_size_in_kb);
+ LOG_INFO("flash size = %dkbytes", flash_size_kb);
- /* read flash option register */
- retval = stm32l4_read_flash_reg(bank, STM32_FLASH_OPTR, &options);
- if (retval != ERROR_OK)
- return retval;
+ /* did we assign a flash size? */
+ assert((flash_size_kb != 0xffff) && flash_size_kb);
stm32l4_info->bank1_sectors = 0;
stm32l4_info->hole_sectors = 0;
int num_pages = 0;
- int page_size = 0;
+ int page_size_kb = 0;
stm32l4_info->dual_bank_mode = false;
+ bool use_dbank_bit = false;
switch (device_id) {
- case 0x415:
- case 0x461:
+ case 0x415: /* STM32L47/L48xx */
+ case 0x461: /* STM32L49/L4Axx */
/* if flash size is max (1M) the device is always dual bank
* 0x415: has variants with 512K
* 0x461: has variants with 512 and 256
* else -> dual bank without gap
* note: the page size is invariant
*/
- page_size = 2048;
- num_pages = flash_size_in_kb / 2;
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages;
/* check DUAL_BANK bit[21] if the flash is less than 1M */
- if (flash_size_in_kb == 1024 || (options & BIT(21))) {
+ if (flash_size_kb == 1024 || (stm32l4_info->optr & BIT(21))) {
stm32l4_info->dual_bank_mode = true;
stm32l4_info->bank1_sectors = num_pages / 2;
}
break;
- case 0x435:
- case 0x462:
- case 0x464:
+ case 0x435: /* STM32L43/L44xx */
+ case 0x460: /* STM32G07/G08xx */
+ case 0x462: /* STM32L45/L46xx */
+ case 0x464: /* STM32L41/L42xx */
+ case 0x466: /* STM32G03/G04xx */
+ case 0x468: /* STM32G43/G44xx */
+ case 0x479: /* STM32G49/G4Axx */
/* single bank flash */
- page_size = 2048;
- num_pages = flash_size_in_kb / 2;
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ break;
+ case 0x467: /* STM32G0B/G0Cxx */
+ /* single/dual bank depending on bit(21) */
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ stm32l4_info->cr_bker_mask = FLASH_BKER_G0;
+
+ /* check DUAL_BANK bit */
+ if (stm32l4_info->optr & BIT(21)) {
+ stm32l4_info->sr_bsy_mask = FLASH_BSY | FLASH_BSY2;
+ stm32l4_info->dual_bank_mode = true;
+ stm32l4_info->bank1_sectors = num_pages / 2;
+ }
+ break;
+ case 0x469: /* STM32G47/G48xx */
+ /* STM32G47/8 can be single/dual bank:
+ * if DUAL_BANK = 0 -> single bank
+ * else -> dual bank WITH gap
+ */
+ page_size_kb = 4;
+ num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages;
+ if (stm32l4_info->optr & BIT(22)) {
+ stm32l4_info->dual_bank_mode = true;
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages / 2;
+
+ /* for devices with trimmed flash, there is a gap between both banks */
+ stm32l4_info->hole_sectors =
+ (part_info->max_flash_size_kb - flash_size_kb) / (2 * page_size_kb);
+ }
break;
- case 0x470:
- case 0x471:
+ case 0x470: /* STM32L4R/L4Sxx */
+ case 0x471: /* STM32L4P5/L4Q5x */
/* STM32L4R/S can be single/dual bank:
* if size = 2M check DBANK bit(22)
* if size = 1M check DB1M bit(21)
* STM32L4P/Q can be single/dual bank
* if size = 1M check DBANK bit(22)
* if size = 512K check DB512K bit(21)
- * in single bank configuration the page size is 8K
- * else (dual bank) the page size is 4K without gap between banks
*/
- page_size = 8192;
- num_pages = flash_size_in_kb / 8;
+ page_size_kb = 8;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ use_dbank_bit = flash_size_kb == part_info->max_flash_size_kb;
+ if ((use_dbank_bit && (stm32l4_info->optr & BIT(22))) ||
+ (!use_dbank_bit && (stm32l4_info->optr & BIT(21)))) {
+ stm32l4_info->dual_bank_mode = true;
+ page_size_kb = 4;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages / 2;
+ }
+ break;
+ case 0x472: /* STM32L55/L56xx */
+ /* STM32L55/L56xx can be single/dual bank:
+ * if size = 512K check DBANK bit(22)
+ * if size = 256K check DB256K bit(21)
+ */
+ page_size_kb = 4;
+ num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages;
- const bool use_dbank_bit = flash_size_in_kb == part_info->max_flash_size_kb;
- if ((use_dbank_bit && (options & BIT(22))) ||
- (!use_dbank_bit && (options & BIT(21)))) {
+ use_dbank_bit = flash_size_kb == part_info->max_flash_size_kb;
+ if ((use_dbank_bit && (stm32l4_info->optr & BIT(22))) ||
+ (!use_dbank_bit && (stm32l4_info->optr & BIT(21)))) {
stm32l4_info->dual_bank_mode = true;
- page_size = 4096;
- num_pages = flash_size_in_kb / 4;
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages / 2;
}
break;
- case 0x495:
+ case 0x495: /* STM32WB5x */
+ case 0x496: /* STM32WB3x */
+ /* single bank flash */
+ page_size_kb = 4;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ break;
+ case 0x497: /* STM32WLEx/WL5x */
/* single bank flash */
- page_size = 4096;
- num_pages = flash_size_in_kb / 4;
+ page_size_kb = 2;
+ num_pages = flash_size_kb / page_size_kb;
stm32l4_info->bank1_sectors = num_pages;
+ if (armv7m->debug_ap->ap_num == 1)
+ stm32l4_info->flash_regs = stm32wl_cpu2_flash_regs;
break;
default:
LOG_ERROR("unsupported device");
LOG_INFO("flash mode : %s-bank", stm32l4_info->dual_bank_mode ? "dual" : "single");
- const int gap_size = stm32l4_info->hole_sectors * page_size;
+ const int gap_size_kb = stm32l4_info->hole_sectors * page_size_kb;
- if (stm32l4_info->dual_bank_mode & gap_size) {
- LOG_INFO("gap detected starting from %0x08" PRIx32 " to %0x08" PRIx32,
- 0x8000000 + stm32l4_info->bank1_sectors * page_size,
- 0x8000000 + stm32l4_info->bank1_sectors * page_size + gap_size);
+ if (gap_size_kb != 0) {
+ LOG_INFO("gap detected from 0x%08x to 0x%08x",
+ STM32_FLASH_BANK_BASE + stm32l4_info->bank1_sectors
+ * page_size_kb * 1024,
+ STM32_FLASH_BANK_BASE + (stm32l4_info->bank1_sectors
+ * page_size_kb + gap_size_kb) * 1024 - 1);
}
- if (bank->sectors) {
- free(bank->sectors);
- bank->sectors = NULL;
- }
+ /* number of significant bits in WRPxxR differs per device,
+ * always right adjusted, on some devices non-implemented
+ * bits read as '0', on others as '1' ...
+ * notably G4 Cat. 2 implement only 6 bits, contradicting the RM
+ */
+
+ /* use *max_flash_size* instead of actual size as the trimmed versions
+ * certainly use the same number of bits
+ * max_flash_size is always power of two, so max_pages too
+ */
+ uint32_t max_pages = stm32l4_info->part_info->max_flash_size_kb / page_size_kb;
+ assert(IS_PWR_OF_2(max_pages));
+
+ /* in dual bank mode number of pages is doubled, but extra bit is bank selection */
+ stm32l4_info->wrpxxr_mask = ((max_pages >> (stm32l4_info->dual_bank_mode ? 1 : 0)) - 1);
+ assert((stm32l4_info->wrpxxr_mask & 0xFFFF0000) == 0);
+ LOG_DEBUG("WRPxxR mask 0x%04" PRIx16, (uint16_t)stm32l4_info->wrpxxr_mask);
- bank->size = flash_size_in_kb * 1024 + gap_size;
- bank->base = 0x08000000;
+ free(bank->sectors);
+
+ bank->size = (flash_size_kb + gap_size_kb) * 1024;
bank->num_sectors = num_pages;
bank->sectors = malloc(sizeof(struct flash_sector) * bank->num_sectors);
- if (bank->sectors == NULL) {
+ if (!bank->sectors) {
LOG_ERROR("failed to allocate bank sectors");
return ERROR_FAIL;
}
- for (i = 0; i < bank->num_sectors; i++) {
- bank->sectors[i].offset = i * page_size;
+ for (unsigned int i = 0; i < bank->num_sectors; i++) {
+ bank->sectors[i].offset = i * page_size_kb * 1024;
/* in dual bank configuration, if there is a gap between banks
* we fix up the sector offset to consider this gap */
if (i >= stm32l4_info->bank1_sectors && stm32l4_info->hole_sectors)
- bank->sectors[i].offset += gap_size;
- bank->sectors[i].size = page_size;
+ bank->sectors[i].offset += gap_size_kb * 1024;
+ bank->sectors[i].size = page_size_kb * 1024;
bank->sectors[i].is_erased = -1;
bank->sectors[i].is_protected = 1;
}
- stm32l4_info->probed = 1;
+ stm32l4_info->probed = true;
return ERROR_OK;
}
static int stm32l4_auto_probe(struct flash_bank *bank)
{
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
- if (stm32l4_info->probed)
- return ERROR_OK;
+ if (stm32l4_info->probed) {
+ uint32_t optr_cur;
+
+ /* read flash option register and re-probe if optr value is changed */
+ int retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_OPTR_INDEX, &optr_cur);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (stm32l4_info->optr == optr_cur)
+ return ERROR_OK;
+ }
return stm32l4_probe(bank);
}
-static int get_stm32l4_info(struct flash_bank *bank, char *buf, int buf_size)
+static int get_stm32l4_info(struct flash_bank *bank, struct command_invocation *cmd)
{
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
const struct stm32l4_part_info *part_info = stm32l4_info->part_info;
if (part_info) {
- const char *rev_str = NULL;
- uint16_t rev_id = stm32l4_info->idcode >> 16;
- for (unsigned int i = 0; i < part_info->num_revs; i++) {
- if (rev_id == part_info->revs[i].rev) {
- rev_str = part_info->revs[i].str;
-
- if (rev_str != NULL) {
- snprintf(buf, buf_size, "%s - Rev: %s",
- part_info->device_str, rev_str);
- return ERROR_OK;
- }
- }
- }
-
- snprintf(buf, buf_size, "%s - Rev: unknown (0x%04x)",
- part_info->device_str, rev_id);
- return ERROR_OK;
+ const uint16_t rev_id = stm32l4_info->idcode >> 16;
+ command_print_sameline(cmd, "%s - Rev %s : 0x%04x", part_info->device_str,
+ get_stm32l4_rev_str(bank), rev_id);
+ if (stm32l4_info->probed)
+ command_print_sameline(cmd, " - %s-bank", get_stm32l4_bank_type_str(bank));
} else {
- snprintf(buf, buf_size, "Cannot identify target as an STM32 L4 or WB device");
- return ERROR_FAIL;
+ command_print_sameline(cmd, "Cannot identify target as an %s device", device_families);
}
return ERROR_OK;
static int stm32l4_mass_erase(struct flash_bank *bank)
{
- int retval;
+ int retval, retval2;
struct target *target = bank->target;
struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("cannot erase OTP memory");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
+
uint32_t action = FLASH_MER1;
- if (stm32l4_info->part_info->has_dual_bank)
+ if (stm32l4_info->part_info->flags & F_HAS_DUAL_BANK)
action |= FLASH_MER2;
if (target->state != TARGET_HALTED) {
return ERROR_TARGET_NOT_HALTED;
}
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* set all FLASH pages as secure */
+ retval = stm32l4_set_secbb(bank, FLASH_SECBB_SECURE);
+ if (retval != ERROR_OK) {
+ /* restore all FLASH pages as non-secure */
+ stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE); /* ignore the return value */
+ return retval;
+ }
+ }
+
retval = stm32l4_unlock_reg(bank);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
/* mass erase flash memory */
retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT / 10);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, action);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, action);
if (retval != ERROR_OK)
- return retval;
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, action | FLASH_STRT);
- if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
- retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
+ retval = stm32l4_write_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX, action | FLASH_STRT);
if (retval != ERROR_OK)
- return retval;
+ goto err_lock;
+
+ retval = stm32l4_wait_status_busy(bank, FLASH_ERASE_TIMEOUT);
+
+err_lock:
+ retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
+
+ if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0)) {
+ /* restore all FLASH pages as non-secure */
+ int retval3 = stm32l4_set_secbb(bank, FLASH_SECBB_NON_SECURE);
+ if (retval3 != ERROR_OK)
+ return retval3;
+ }
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, FLASH_LOCK);
if (retval != ERROR_OK)
return retval;
- return ERROR_OK;
+ return retval2;
}
COMMAND_HANDLER(stm32l4_handle_mass_erase_command)
{
- int i;
-
if (CMD_ARGC < 1) {
command_print(CMD, "stm32l4x mass_erase <STM32L4 bank>");
return ERROR_COMMAND_SYNTAX_ERROR;
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
retval = stm32l4_mass_erase(bank);
- if (retval == ERROR_OK) {
- /* set all sectors as erased */
- for (i = 0; i < bank->num_sectors; i++)
- bank->sectors[i].is_erased = 1;
-
+ if (retval == ERROR_OK)
command_print(CMD, "stm32l4x mass erase complete");
- } else {
+ else
command_print(CMD, "stm32l4x mass erase failed");
- }
return retval;
}
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
uint32_t reg_offset, reg_addr;
uint32_t value = 0;
- reg_offset = strtoul(CMD_ARGV[1], NULL, 16);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[1], reg_offset);
reg_addr = stm32l4_get_flash_reg(bank, reg_offset);
retval = stm32l4_read_flash_reg(bank, reg_offset, &value);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
command_print(CMD, "Option Register: <0x%" PRIx32 "> = 0x%" PRIx32 "", reg_addr, value);
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
uint32_t reg_offset;
uint32_t value = 0;
uint32_t mask = 0xFFFFFFFF;
- reg_offset = strtoul(CMD_ARGV[1], NULL, 16);
- value = strtoul(CMD_ARGV[2], NULL, 16);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[1], reg_offset);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[2], value);
+
if (CMD_ARGC > 3)
- mask = strtoul(CMD_ARGV[3], NULL, 16);
+ COMMAND_PARSE_NUMBER(u32, CMD_ARGV[3], mask);
command_print(CMD, "%s Option written.\n"
"INFO: a reset or power cycle is required "
return retval;
}
-COMMAND_HANDLER(stm32l4_handle_option_load_command)
+COMMAND_HANDLER(stm32l4_handle_trustzone_command)
{
- if (CMD_ARGC < 1)
+ if (CMD_ARGC < 1 || CMD_ARGC > 2)
return ERROR_COMMAND_SYNTAX_ERROR;
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
- retval = stm32l4_unlock_reg(bank);
- if (ERROR_OK != retval)
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ if (!(stm32l4_info->part_info->flags & F_HAS_TZ)) {
+ LOG_ERROR("This device does not have a TrustZone");
+ return ERROR_FAIL;
+ }
+
+ retval = stm32l4_read_flash_reg_by_index(bank, STM32_FLASH_OPTR_INDEX, &stm32l4_info->optr);
+ if (retval != ERROR_OK)
return retval;
- retval = stm32l4_unlock_option_reg(bank);
- if (ERROR_OK != retval)
+ stm32l4_sync_rdp_tzen(bank);
+
+ if (CMD_ARGC == 1) {
+ /* only display the TZEN value */
+ LOG_INFO("Global TrustZone Security is %s", stm32l4_info->tzen ? "enabled" : "disabled");
+ return ERROR_OK;
+ }
+
+ bool new_tzen;
+ COMMAND_PARSE_ENABLE(CMD_ARGV[1], new_tzen);
+
+ if (new_tzen == stm32l4_info->tzen) {
+ LOG_INFO("The requested TZEN is already programmed");
+ return ERROR_OK;
+ }
+
+ if (new_tzen) {
+ if (stm32l4_info->rdp != RDP_LEVEL_0) {
+ LOG_ERROR("TZEN can be set only when RDP level is 0");
+ return ERROR_FAIL;
+ }
+ retval = stm32l4_write_option(bank, stm32l4_info->flash_regs[STM32_FLASH_OPTR_INDEX],
+ FLASH_TZEN, FLASH_TZEN);
+ } else {
+ /* Deactivation of TZEN (from 1 to 0) is only possible when the RDP is
+ * changing to level 0 (from level 1 to level 0 or from level 0.5 to level 0). */
+ if (stm32l4_info->rdp != RDP_LEVEL_1 && stm32l4_info->rdp != RDP_LEVEL_0_5) {
+ LOG_ERROR("Deactivation of TZEN is only possible when the RDP is changing to level 0");
+ return ERROR_FAIL;
+ }
+
+ retval = stm32l4_write_option(bank, stm32l4_info->flash_regs[STM32_FLASH_OPTR_INDEX],
+ RDP_LEVEL_0, FLASH_RDP_MASK | FLASH_TZEN);
+ }
+
+ if (retval != ERROR_OK)
return retval;
- /* Write the OBLLAUNCH bit in CR -> Cause device "POR" and option bytes reload */
- retval = stm32l4_write_flash_reg(bank, STM32_FLASH_CR, FLASH_OBLLAUNCH);
+ return stm32l4_perform_obl_launch(bank);
+}
- command_print(CMD, "stm32l4x option load (POR) completed.");
- return retval;
+COMMAND_HANDLER(stm32l4_handle_flashloader_command)
+{
+ if (CMD_ARGC < 1 || CMD_ARGC > 2)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ struct flash_bank *bank;
+ int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
+ if (retval != ERROR_OK)
+ return retval;
+
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+
+ if (CMD_ARGC == 2)
+ COMMAND_PARSE_ENABLE(CMD_ARGV[1], stm32l4_info->use_flashloader);
+
+ command_print(CMD, "FlashLoader usage is %s", stm32l4_info->use_flashloader ? "enabled" : "disabled");
+
+ return ERROR_OK;
+}
+
+COMMAND_HANDLER(stm32l4_handle_option_load_command)
+{
+ if (CMD_ARGC != 1)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ struct flash_bank *bank;
+ int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
+ if (retval != ERROR_OK)
+ return retval;
+
+ retval = stm32l4_perform_obl_launch(bank);
+ if (retval != ERROR_OK) {
+ command_print(CMD, "stm32l4x option load failed");
+ return retval;
+ }
+
+
+ command_print(CMD, "stm32l4x option load completed. Power-on reset might be required");
+
+ return ERROR_OK;
}
COMMAND_HANDLER(stm32l4_handle_lock_command)
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("cannot lock/unlock OTP memory");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
+
target = bank->target;
if (target->state != TARGET_HALTED) {
}
/* set readout protection level 1 by erasing the RDP option byte */
- if (stm32l4_write_option(bank, STM32_FLASH_OPTR, 0, 0x000000FF) != ERROR_OK) {
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ if (stm32l4_write_option(bank, stm32l4_info->flash_regs[STM32_FLASH_OPTR_INDEX],
+ RDP_LEVEL_1, FLASH_RDP_MASK) != ERROR_OK) {
command_print(CMD, "%s failed to lock device", bank->driver->name);
return ERROR_OK;
}
struct flash_bank *bank;
int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
- if (ERROR_OK != retval)
+ if (retval != ERROR_OK)
return retval;
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("cannot lock/unlock OTP memory");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
+
target = bank->target;
if (target->state != TARGET_HALTED) {
return ERROR_TARGET_NOT_HALTED;
}
- if (stm32l4_write_option(bank, STM32_FLASH_OPTR, RDP_LEVEL_0, 0x000000FF) != ERROR_OK) {
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ if (stm32l4_write_option(bank, stm32l4_info->flash_regs[STM32_FLASH_OPTR_INDEX],
+ RDP_LEVEL_0, FLASH_RDP_MASK) != ERROR_OK) {
command_print(CMD, "%s failed to unlock device", bank->driver->name);
return ERROR_OK;
}
return ERROR_OK;
}
+COMMAND_HANDLER(stm32l4_handle_wrp_info_command)
+{
+ if (CMD_ARGC < 1 || CMD_ARGC > 2)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ struct flash_bank *bank;
+ int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (stm32l4_is_otp(bank)) {
+ LOG_ERROR("OTP memory does not have write protection areas");
+ return ERROR_FLASH_OPER_UNSUPPORTED;
+ }
+
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
+ enum stm32_bank_id dev_bank_id = STM32_ALL_BANKS;
+ if (CMD_ARGC == 2) {
+ if (strcmp(CMD_ARGV[1], "bank1") == 0)
+ dev_bank_id = STM32_BANK1;
+ else if (strcmp(CMD_ARGV[1], "bank2") == 0)
+ dev_bank_id = STM32_BANK2;
+ else
+ return ERROR_COMMAND_ARGUMENT_INVALID;
+ }
+
+ if (dev_bank_id == STM32_BANK2) {
+ if (!(stm32l4_info->part_info->flags & F_HAS_DUAL_BANK)) {
+ LOG_ERROR("this device has no second bank");
+ return ERROR_FAIL;
+ } else if (!stm32l4_info->dual_bank_mode) {
+ LOG_ERROR("this device is configured in single bank mode");
+ return ERROR_FAIL;
+ }
+ }
+
+ int ret;
+ unsigned int n_wrp, i;
+ struct stm32l4_wrp wrpxy[4];
+
+ ret = stm32l4_get_all_wrpxy(bank, dev_bank_id, wrpxy, &n_wrp);
+ if (ret != ERROR_OK)
+ return ret;
+
+ /* use bitmap and range helpers to better describe protected areas */
+ DECLARE_BITMAP(pages, bank->num_sectors);
+ bitmap_zero(pages, bank->num_sectors);
+
+ for (i = 0; i < n_wrp; i++) {
+ if (wrpxy[i].used) {
+ for (int p = wrpxy[i].first; p <= wrpxy[i].last; p++)
+ set_bit(p, pages);
+ }
+ }
+
+ /* we have at most 'n_wrp' WRP areas */
+ struct range ranges[n_wrp];
+ unsigned int ranges_count = 0;
+
+ bitmap_to_ranges(pages, bank->num_sectors, ranges, &ranges_count);
+
+ if (ranges_count > 0) {
+ /* pretty-print the protected ranges */
+ char *ranges_str = range_print_alloc(ranges, ranges_count);
+ command_print(CMD, "protected areas: %s", ranges_str);
+ free(ranges_str);
+ } else
+ command_print(CMD, "no protected areas");
+
+ return ERROR_OK;
+}
+
+COMMAND_HANDLER(stm32l4_handle_otp_command)
+{
+ if (CMD_ARGC < 2)
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ struct flash_bank *bank;
+ int retval = CALL_COMMAND_HANDLER(flash_command_get_bank, 0, &bank);
+ if (retval != ERROR_OK)
+ return retval;
+
+ if (!stm32l4_is_otp(bank)) {
+ command_print(CMD, "the specified bank is not an OTP memory");
+ return ERROR_FAIL;
+ }
+ if (strcmp(CMD_ARGV[1], "enable") == 0)
+ stm32l4_otp_enable(bank, true);
+ else if (strcmp(CMD_ARGV[1], "disable") == 0)
+ stm32l4_otp_enable(bank, false);
+ else if (strcmp(CMD_ARGV[1], "show") == 0)
+ command_print(CMD, "OTP memory bank #%d is %s for write commands.",
+ bank->bank_number, stm32l4_otp_is_enabled(bank) ? "enabled" : "disabled");
+ else
+ return ERROR_COMMAND_SYNTAX_ERROR;
+
+ return ERROR_OK;
+}
+
static const struct command_registration stm32l4_exec_command_handlers[] = {
{
.name = "lock",
.usage = "bank_id",
.help = "Unlock entire protected flash device.",
},
+ {
+ .name = "flashloader",
+ .handler = stm32l4_handle_flashloader_command,
+ .mode = COMMAND_EXEC,
+ .usage = "<bank_id> [enable|disable]",
+ .help = "Configure the flashloader usage",
+ },
{
.name = "mass_erase",
.handler = stm32l4_handle_mass_erase_command,
.usage = "bank_id reg_offset value mask",
.help = "Write device option bit fields with provided value.",
},
+ {
+ .name = "trustzone",
+ .handler = stm32l4_handle_trustzone_command,
+ .mode = COMMAND_EXEC,
+ .usage = "<bank_id> [enable|disable]",
+ .help = "Configure TrustZone security",
+ },
+ {
+ .name = "wrp_info",
+ .handler = stm32l4_handle_wrp_info_command,
+ .mode = COMMAND_EXEC,
+ .usage = "bank_id [bank1|bank2]",
+ .help = "list the protected areas using WRP",
+ },
{
.name = "option_load",
.handler = stm32l4_handle_option_load_command,
.usage = "bank_id",
.help = "Force re-load of device options (will cause device reset).",
},
+ {
+ .name = "otp",
+ .handler = stm32l4_handle_otp_command,
+ .mode = COMMAND_EXEC,
+ .usage = "<bank_id> <enable|disable|show>",
+ .help = "OTP (One Time Programmable) memory write enable/disable",
+ },
COMMAND_REGISTRATION_DONE
};
projects / fw / openocd / blobdiff