if (!ao_fifo_full(ao_usart1_rx_fifo))
ao_fifo_insert(ao_usart1_rx_fifo, U1DBUF);
ao_wakeup(&ao_usart1_rx_fifo);
+#if USE_SERIAL_STDIN
+ ao_wakeup(&ao_stdin_ready);
+#endif
}
static __xdata uint8_t ao_serial_tx1_started;
ao_wakeup(&ao_usart1_tx_fifo);
}
-static __pdata serial_echo;
-
char
ao_serial_getchar(void) __critical
{
while (ao_fifo_empty(ao_usart1_rx_fifo))
ao_sleep(&ao_usart1_rx_fifo);
ao_fifo_remove(ao_usart1_rx_fifo, c);
- if (serial_echo) {
- printf("%02x ", ((int) c) & 0xff);
- if (c >= ' ')
- putchar(c);
- putchar('\n');
- flush();
- }
return c;
}
+#if USE_SERIAL_STDIN
+char
+ao_serial_pollchar(void) __critical
+{
+ char c;
+ if (ao_fifo_empty(ao_usart1_rx_fifo))
+ return AO_READ_AGAIN;
+ ao_fifo_remove(ao_usart1_rx_fifo,c);
+ return c;
+}
+#endif
+
void
ao_serial_putchar(char c) __critical
{
ao_serial_tx1_start();
}
-static void
+void
ao_serial_drain(void) __critical
{
while (!ao_fifo_empty(ao_usart1_tx_fifo))
ao_sleep(&ao_usart1_tx_fifo);
}
-static void
-monitor_serial(void)
-{
- ao_cmd_hex();
- serial_echo = ao_cmd_lex_i != 0;
-}
-
-__code struct ao_cmds ao_serial_cmds[] = {
- { 'M', monitor_serial, "M <enable> Monitor serial data" },
- { 0, monitor_serial, NULL },
-};
-
static const struct {
uint8_t baud;
uint8_t gcr;
/* .baud = */ 163,
/* .gcr = */ (8 << UxGCR_BAUD_E_SHIFT) | UxGCR_ORDER_LSB
},
+ /* [AO_SERIAL_SPEED_19200] = */ {
+ /* .baud = */ 163,
+ /* .gcr = */ (9 << UxGCR_BAUD_E_SHIFT) | UxGCR_ORDER_LSB
+ },
/* [AO_SERIAL_SPEED_57600] = */ {
/* .baud = */ 59,
/* .gcr = */ (11 << UxGCR_BAUD_E_SHIFT) | UxGCR_ORDER_LSB
ao_serial_drain();
if (speed > AO_SERIAL_SPEED_57600)
return;
+ U1UCR |= UxUCR_FLUSH;
U1BAUD = ao_serial_speeds[speed].baud;
U1GCR = ao_serial_speeds[speed].gcr;
}
/* Set up the USART pin assignment */
PERCFG = (PERCFG & ~PERCFG_U1CFG_ALT_MASK) | PERCFG_U1CFG_ALT_2;
- /* ee has already set the P2SEL bits */
+ P2SEL = (P2SEL & ~(P2SEL_PRI3P1_MASK | P2SEL_PRI2P1_MASK)) |
+ (P2SEL_PRI3P1_USART1 | P2SEL_PRI2P1_USART1);
/* Make the USART pins be controlled by the USART */
P1SEL |= (1 << 6) | (1 << 7);
/* Reasonable serial parameters */
U1UCR = (UxUCR_FLUSH |
UxUCR_FLOW_DISABLE |
- UxUCR_D9_ODD_PARITY |
+ UxUCR_D9_EVEN_PARITY |
UxUCR_BIT9_8_BITS |
UxUCR_PARITY_DISABLE |
UxUCR_SPB_1_STOP_BIT |
IEN0 |= IEN0_URX1IE;
IEN2 |= IEN2_UTX1IE;
-
- ao_cmd_register(&ao_serial_cmds[0]);
}