--- /dev/null
+/**
+ ******************************************************************************
+ * @file usb_conf.h
+ * @author MCD Application Team
+ * @version V2.0.0
+ * @date 22-July-2011
+ * @brief general low level driver configuration
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ * <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2>
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __USB_CONF__H__
+#define __USB_CONF__H__
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f2xx.h"
+
+
+/** @addtogroup USB_OTG_DRIVER
+ * @{
+ */
+
+/** @defgroup USB_CONF
+ * @brief USB low level driver configuration file
+ * @{
+ */
+
+/** @defgroup USB_CONF_Exported_Defines
+ * @{
+ */
+
+/* USB Core and PHY interface configuration.
+ Tip: To avoid modifying these defines each time you need to change the USB
+ configuration, you can declare the needed define in your toolchain
+ compiler preprocessor.
+ */
+#ifndef USE_USB_OTG_FS
+ //#define USE_USB_OTG_FS
+#endif /* USE_USB_OTG_FS */
+
+#ifndef USE_USB_OTG_HS
+ //#define USE_USB_OTG_HS
+#endif /* USE_USB_OTG_HS */
+
+#ifndef USE_ULPI_PHY
+ //#define USE_ULPI_PHY
+#endif /* USE_ULPI_PHY */
+
+#ifndef USE_EMBEDDED_PHY
+ //#define USE_EMBEDDED_PHY
+#endif /* USE_EMBEDDED_PHY */
+
+#ifndef USE_I2C_PHY
+ //#define USE_I2C_PHY
+#endif /* USE_I2C_PHY */
+
+
+#ifdef USE_USB_OTG_FS
+ #define USB_OTG_FS_CORE
+#endif
+
+#ifdef USE_USB_OTG_HS
+ #define USB_OTG_HS_CORE
+#endif
+
+/*******************************************************************************
+* FIFO Size Configuration in Device mode
+*
+* (i) Receive data FIFO size = RAM for setup packets +
+* OUT endpoint control information +
+* data OUT packets + miscellaneous
+* Space = ONE 32-bits words
+* --> RAM for setup packets = 10 spaces
+* (n is the nbr of CTRL EPs the device core supports)
+* --> OUT EP CTRL info = 1 space
+* (one space for status information written to the FIFO along with each
+* received packet)
+* --> data OUT packets = (Largest Packet Size / 4) + 1 spaces
+* (MINIMUM to receive packets)
+* --> OR data OUT packets = at least 2*(Largest Packet Size / 4) + 1 spaces
+* (if high-bandwidth EP is enabled or multiple isochronous EPs)
+* --> miscellaneous = 1 space per OUT EP
+* (one space for transfer complete status information also pushed to the
+* FIFO with each endpoint's last packet)
+*
+* (ii)MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for
+* that particular IN EP. More space allocated in the IN EP Tx FIFO results
+* in a better performance on the USB and can hide latencies on the AHB.
+*
+* (iii) TXn min size = 16 words. (n : Transmit FIFO index)
+* (iv) When a TxFIFO is not used, the Configuration should be as follows:
+* case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
+* --> Txm can use the space allocated for Txn.
+* case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
+* --> Txn should be configured with the minimum space of 16 words
+* (v) The FIFO is used optimally when used TxFIFOs are allocated in the top
+* of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
+*******************************************************************************/
+
+/*******************************************************************************
+* FIFO Size Configuration in Host mode
+*
+* (i) Receive data FIFO size = (Largest Packet Size / 4) + 1 or
+* 2x (Largest Packet Size / 4) + 1, If a
+* high-bandwidth channel or multiple isochronous
+* channels are enabled
+*
+* (ii) For the host nonperiodic Transmit FIFO is the largest maximum packet size
+* for all supported nonperiodic OUT channels. Typically, a space
+* corresponding to two Largest Packet Size is recommended.
+*
+* (iii) The minimum amount of RAM required for Host periodic Transmit FIFO is
+* the largest maximum packet size for all supported periodic OUT channels.
+* If there is at least one High Bandwidth Isochronous OUT endpoint,
+* then the space must be at least two times the maximum packet size for
+* that channel.
+*******************************************************************************/
+
+/****************** USB OTG HS CONFIGURATION **********************************/
+#ifdef USB_OTG_HS_CORE
+ #define RX_FIFO_HS_SIZE 512
+ #define TX0_FIFO_HS_SIZE 512
+ #define TX1_FIFO_HS_SIZE 512
+ #define TX2_FIFO_HS_SIZE 0
+ #define TX3_FIFO_HS_SIZE 0
+ #define TX4_FIFO_HS_SIZE 0
+ #define TX5_FIFO_HS_SIZE 0
+ #define TXH_NP_HS_FIFOSIZ 96
+ #define TXH_P_HS_FIFOSIZ 96
+
+ //#define USB_OTG_HS_LOW_PWR_MGMT_SUPPORT
+ //#define USB_OTG_HS_SOF_OUTPUT_ENABLED
+
+ //#define USB_OTG_INTERNAL_VBUS_ENABLED
+ #define USB_OTG_EXTERNAL_VBUS_ENABLED
+
+ #ifdef USE_ULPI_PHY
+ #define USB_OTG_ULPI_PHY_ENABLED
+ #endif
+ #ifdef USE_EMBEDDED_PHY
+ #define USB_OTG_EMBEDDED_PHY_ENABLED
+ #endif
+ #ifdef USE_I2C_PHY
+ #define USB_OTG_I2C_PHY_ENABLED
+ #endif
+ #define USB_OTG_HS_INTERNAL_DMA_ENABLED
+ #define USB_OTG_HS_DEDICATED_EP1_ENABLED
+#endif
+
+/****************** USB OTG FS CONFIGURATION **********************************/
+#ifdef USB_OTG_FS_CORE
+ #define RX_FIFO_FS_SIZE 128
+ #define TX0_FIFO_FS_SIZE 64
+ #define TX1_FIFO_FS_SIZE 128
+ #define TX2_FIFO_FS_SIZE 0
+ #define TX3_FIFO_FS_SIZE 0
+ #define TXH_NP_HS_FIFOSIZ 96
+ #define TXH_P_HS_FIFOSIZ 96
+
+ //#define USB_OTG_FS_LOW_PWR_MGMT_SUPPORT
+ //#define USB_OTG_FS_SOF_OUTPUT_ENABLED
+#endif
+
+/****************** USB OTG MODE CONFIGURATION ********************************/
+//#define USE_HOST_MODE
+#define USE_DEVICE_MODE
+//#define USE_OTG_MODE
+
+
+#ifndef USB_OTG_FS_CORE
+ #ifndef USB_OTG_HS_CORE
+ #error "USB_OTG_HS_CORE or USB_OTG_FS_CORE should be defined"
+ #endif
+#endif
+
+
+#ifndef USE_DEVICE_MODE
+ #ifndef USE_HOST_MODE
+ #error "USE_DEVICE_MODE or USE_HOST_MODE should be defined"
+ #endif
+#endif
+
+#ifndef USE_USB_OTG_HS
+ #ifndef USE_USB_OTG_FS
+ #error "USE_USB_OTG_HS or USE_USB_OTG_FS should be defined"
+ #endif
+#else //USE_USB_OTG_HS
+ #ifndef USE_ULPI_PHY
+ #ifndef USE_EMBEDDED_PHY
+ #ifndef USE_I2C_PHY
+ #error "USE_ULPI_PHY or USE_EMBEDDED_PHY or USE_I2C_PHY should be defined"
+ #endif
+ #endif
+ #endif
+#endif
+
+/****************** C Compilers dependant keywords ****************************/
+/* In HS mode and when the DMA is used, all variables and data structures dealing
+ with the DMA during the transaction process should be 4-bytes aligned */
+#ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED
+ #if defined (__GNUC__) /* GNU Compiler */
+ #define __ALIGN_END __attribute__ ((aligned (4)))
+ #define __ALIGN_BEGIN
+ #else
+ #define __ALIGN_END
+ #if defined (__CC_ARM) /* ARM Compiler */
+ #define __ALIGN_BEGIN __align(4)
+ #elif defined (__ICCARM__) /* IAR Compiler */
+ #define __ALIGN_BEGIN
+ #elif defined (__TASKING__) /* TASKING Compiler */
+ #define __ALIGN_BEGIN __align(4)
+ #endif /* __CC_ARM */
+ #endif /* __GNUC__ */
+#else
+ #define __ALIGN_BEGIN
+ #define __ALIGN_END
+#endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */
+
+/* __packed keyword used to decrease the data type alignment to 1-byte */
+#if defined (__CC_ARM) /* ARM Compiler */
+ #define __packed __packed
+#elif defined (__ICCARM__) /* IAR Compiler */
+ #define __packed __packed
+#elif defined ( __GNUC__ ) /* GNU Compiler */
+ #define __packed __attribute__ ((__packed__))
+#elif defined (__TASKING__) /* TASKING Compiler */
+ #define __packed __unaligned
+#endif /* __CC_ARM */
+
+/**
+ * @}
+ */
+
+
+/** @defgroup USB_CONF_Exported_Types
+ * @{
+ */
+/**
+ * @}
+ */
+
+
+/** @defgroup USB_CONF_Exported_Macros
+ * @{
+ */
+/**
+ * @}
+ */
+
+/** @defgroup USB_CONF_Exported_Variables
+ * @{
+ */
+/**
+ * @}
+ */
+
+/** @defgroup USB_CONF_Exported_FunctionsPrototype
+ * @{
+ */
+/**
+ * @}
+ */
+
+
+#endif //__USB_CONF__H__
+
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
+
projects / fw / stlink / blobdiff