--- /dev/null
+/**
+ ******************************************************************************
+ * @file stm32f4xx_rcc.c
+ * @author MCD Application Team
+ * @version V1.0.0RC1
+ * @date 25-August-2011
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the Reset and clock control (RCC) peripheral:
+ * - Internal/external clocks, PLL, CSS and MCO configuration
+ * - System, AHB and APB busses clocks configuration
+ * - Peripheral clocks configuration
+ * - Interrupts and flags management
+ *
+ * @verbatim
+ *
+ * ===================================================================
+ * RCC specific features
+ * ===================================================================
+ *
+ * After reset the device is running from Internal High Speed oscillator
+ * (HSI 16MHz) with Flash 0 wait state, Flash prefetch buffer, D-Cache
+ * and I-Cache are disabled, and all peripherals are off except internal
+ * SRAM, Flash and JTAG.
+ * - There is no prescaler on High speed (AHB) and Low speed (APB) busses;
+ * all peripherals mapped on these busses are running at HSI speed.
+ * - The clock for all peripherals is switched off, except the SRAM and FLASH.
+ * - All GPIOs are in input floating state, except the JTAG pins which
+ * are assigned to be used for debug purpose.
+ *
+ * Once the device started from reset, the user application has to:
+ * - Configure the clock source to be used to drive the System clock
+ * (if the application needs higher frequency/performance)
+ * - Configure the System clock frequency and Flash settings
+ * - Configure the AHB and APB busses prescalers
+ * - Enable the clock for the peripheral(s) to be used
+ * - Configure the clock source(s) for peripherals which clocks are not
+ * derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG)
+ *
+ * @endverbatim
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ * <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2>
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_rcc.h"
+
+/** @addtogroup STM32F4xx_StdPeriph_Driver
+ * @{
+ */
+
+/** @defgroup RCC
+ * @brief RCC driver modules
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* ------------ RCC registers bit address in the alias region ----------- */
+#define RCC_OFFSET (RCC_BASE - PERIPH_BASE)
+/* --- CR Register ---*/
+/* Alias word address of HSION bit */
+#define CR_OFFSET (RCC_OFFSET + 0x00)
+#define HSION_BitNumber 0x00
+#define CR_HSION_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (HSION_BitNumber * 4))
+/* Alias word address of CSSON bit */
+#define CSSON_BitNumber 0x13
+#define CR_CSSON_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (CSSON_BitNumber * 4))
+/* Alias word address of PLLON bit */
+#define PLLON_BitNumber 0x18
+#define CR_PLLON_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PLLON_BitNumber * 4))
+/* Alias word address of PLLI2SON bit */
+#define PLLI2SON_BitNumber 0x1A
+#define CR_PLLI2SON_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PLLI2SON_BitNumber * 4))
+
+/* --- CFGR Register ---*/
+/* Alias word address of I2SSRC bit */
+#define CFGR_OFFSET (RCC_OFFSET + 0x08)
+#define I2SSRC_BitNumber 0x17
+#define CFGR_I2SSRC_BB (PERIPH_BB_BASE + (CFGR_OFFSET * 32) + (I2SSRC_BitNumber * 4))
+
+/* --- BDCR Register ---*/
+/* Alias word address of RTCEN bit */
+#define BDCR_OFFSET (RCC_OFFSET + 0x70)
+#define RTCEN_BitNumber 0x0F
+#define BDCR_RTCEN_BB (PERIPH_BB_BASE + (BDCR_OFFSET * 32) + (RTCEN_BitNumber * 4))
+/* Alias word address of BDRST bit */
+#define BDRST_BitNumber 0x10
+#define BDCR_BDRST_BB (PERIPH_BB_BASE + (BDCR_OFFSET * 32) + (BDRST_BitNumber * 4))
+/* --- CSR Register ---*/
+/* Alias word address of LSION bit */
+#define CSR_OFFSET (RCC_OFFSET + 0x74)
+#define LSION_BitNumber 0x00
+#define CSR_LSION_BB (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (LSION_BitNumber * 4))
+/* ---------------------- RCC registers bit mask ------------------------ */
+/* CFGR register bit mask */
+#define CFGR_MCO2_RESET_MASK ((uint32_t)0x07FFFFFF)
+#define CFGR_MCO1_RESET_MASK ((uint32_t)0xF89FFFFF)
+
+/* RCC Flag Mask */
+#define FLAG_MASK ((uint8_t)0x1F)
+
+/* CR register byte 3 (Bits[23:16]) base address */
+#define CR_BYTE3_ADDRESS ((uint32_t)0x40023802)
+
+/* CIR register byte 2 (Bits[15:8]) base address */
+#define CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + 0x0C + 0x01))
+
+/* CIR register byte 3 (Bits[23:16]) base address */
+#define CIR_BYTE3_ADDRESS ((uint32_t)(RCC_BASE + 0x0C + 0x02))
+
+/* BDCR register base address */
+#define BDCR_ADDRESS (PERIPH_BASE + BDCR_OFFSET)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+static __I uint8_t APBAHBPrescTable[16] = {0, 0, 0, 0, 1, 2, 3, 4, 1, 2, 3, 4, 6, 7, 8, 9};
+
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RCC_Private_Functions
+ * @{
+ */
+
+/** @defgroup RCC_Group1 Internal and external clocks, PLL, CSS and MCO configuration functions
+ * @brief Internal and external clocks, PLL, CSS and MCO configuration functions
+ *
+@verbatim
+ ===============================================================================
+ Internal/external clocks, PLL, CSS and MCO configuration functions
+ ===============================================================================
+
+ This section provide functions allowing to configure the internal/external clocks,
+ PLLs, CSS and MCO pins.
+
+ 1. HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through
+ the PLL as System clock source.
+
+ 2. LSI (low-speed internal), 32 KHz low consumption RC used as IWDG and/or RTC
+ clock source.
+
+ 3. HSE (high-speed external), 4 to 26 MHz crystal oscillator used directly or
+ through the PLL as System clock source. Can be used also as RTC clock source.
+
+ 4. LSE (low-speed external), 32 KHz oscillator used as RTC clock source.
+
+ 5. PLL (clocked by HSI or HSE), featuring two different output clocks:
+ - The first output is used to generate the high speed system clock (up to 120 MHz)
+ - The second output is used to generate the clock for the USB OTG FS (48 MHz),
+ the random analog generator (<=48 MHz) and the SDIO (<= 48 MHz).
+
+ 6. PLLI2S (clocked by HSI or HSE), used to generate an accurate clock to achieve
+ high-quality audio performance on the I2S interface.
+
+ 7. CSS (Clock security system), once enable and if a HSE clock failure occurs
+ (HSE used directly or through PLL as System clock source), the System clock
+ is automatically switched to HSI and an interrupt is generated if enabled.
+ The interrupt is linked to the Cortex-M4 NMI (Non-Maskable Interrupt)
+ exception vector.
+
+ 8. MCO1 (microcontroller clock output), used to output HSI, LSE, HSE or PLL
+ clock (through a configurable prescaler) on PA8 pin.
+
+ 9. MCO2 (microcontroller clock output), used to output HSE, PLL, SYSCLK or PLLI2S
+ clock (through a configurable prescaler) on PC9 pin.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Resets the RCC clock configuration to the default reset state.
+ * @note The default reset state of the clock configuration is given below:
+ * - HSI ON and used as system clock source
+ * - HSE, PLL and PLLI2S OFF
+ * - AHB, APB1 and APB2 prescaler set to 1.
+ * - CSS, MCO1 and MCO2 OFF
+ * - All interrupts disabled
+ * @note This function doesn't modify the configuration of the
+ * - Peripheral clocks
+ * - LSI, LSE and RTC clocks
+ * @param None
+ * @retval None
+ */
+void RCC_DeInit(void)
+{
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+}
+
+/**
+ * @brief Configures the External High Speed oscillator (HSE).
+ * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application
+ * software should wait on HSERDY flag to be set indicating that HSE clock
+ * is stable and can be used to clock the PLL and/or system clock.
+ * @note HSE state can not be changed if it is used directly or through the
+ * PLL as system clock. In this case, you have to select another source
+ * of the system clock then change the HSE state (ex. disable it).
+ * @note The HSE is stopped by hardware when entering STOP and STANDBY modes.
+ * @note This function reset the CSSON bit, so if the Clock security system(CSS)
+ * was previously enabled you have to enable it again after calling this
+ * function.
+ * @param RCC_HSE: specifies the new state of the HSE.
+ * This parameter can be one of the following values:
+ * @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after
+ * 6 HSE oscillator clock cycles.
+ * @arg RCC_HSE_ON: turn ON the HSE oscillator
+ * @arg RCC_HSE_Bypass: HSE oscillator bypassed with external clock
+ * @retval None
+ */
+void RCC_HSEConfig(uint8_t RCC_HSE)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_HSE(RCC_HSE));
+
+ /* Reset HSEON and HSEBYP bits before configuring the HSE ------------------*/
+ *(__IO uint8_t *) CR_BYTE3_ADDRESS = RCC_HSE_OFF;
+
+ /* Set the new HSE configuration -------------------------------------------*/
+ *(__IO uint8_t *) CR_BYTE3_ADDRESS = RCC_HSE;
+}
+
+/**
+ * @brief Waits for HSE start-up.
+ * @note This functions waits on HSERDY flag to be set and return SUCCESS if
+ * this flag is set, otherwise returns ERROR if the timeout is reached
+ * and this flag is not set. The timeout value is defined by the constant
+ * HSE_STARTUP_TIMEOUT in stm32f4xx.h file. You can tailor it depending
+ * on the HSE crystal used in your application.
+ * @param None
+ * @retval An ErrorStatus enumeration value:
+ * - SUCCESS: HSE oscillator is stable and ready to use
+ * - ERROR: HSE oscillator not yet ready
+ */
+ErrorStatus RCC_WaitForHSEStartUp(void)
+{
+ __IO uint32_t startupcounter = 0;
+ ErrorStatus status = ERROR;
+ FlagStatus hsestatus = RESET;
+ /* Wait till HSE is ready and if Time out is reached exit */
+ do
+ {
+ hsestatus = RCC_GetFlagStatus(RCC_FLAG_HSERDY);
+ startupcounter++;
+ } while((startupcounter != HSE_STARTUP_TIMEOUT) && (hsestatus == RESET));
+
+ if (RCC_GetFlagStatus(RCC_FLAG_HSERDY) != RESET)
+ {
+ status = SUCCESS;
+ }
+ else
+ {
+ status = ERROR;
+ }
+ return (status);
+}
+
+/**
+ * @brief Adjusts the Internal High Speed oscillator (HSI) calibration value.
+ * @note The calibration is used to compensate for the variations in voltage
+ * and temperature that influence the frequency of the internal HSI RC.
+ * @param HSICalibrationValue: specifies the calibration trimming value.
+ * This parameter must be a number between 0 and 0x1F.
+ * @retval None
+ */
+void RCC_AdjustHSICalibrationValue(uint8_t HSICalibrationValue)
+{
+ uint32_t tmpreg = 0;
+ /* Check the parameters */
+ assert_param(IS_RCC_CALIBRATION_VALUE(HSICalibrationValue));
+
+ tmpreg = RCC->CR;
+
+ /* Clear HSITRIM[4:0] bits */
+ tmpreg &= ~RCC_CR_HSITRIM;
+
+ /* Set the HSITRIM[4:0] bits according to HSICalibrationValue value */
+ tmpreg |= (uint32_t)HSICalibrationValue << 3;
+
+ /* Store the new value */
+ RCC->CR = tmpreg;
+}
+
+/**
+ * @brief Enables or disables the Internal High Speed oscillator (HSI).
+ * @note The HSI is stopped by hardware when entering STOP and STANDBY modes.
+ * It is used (enabled by hardware) as system clock source after startup
+ * from Reset, wakeup from STOP and STANDBY mode, or in case of failure
+ * of the HSE used directly or indirectly as system clock (if the Clock
+ * Security System CSS is enabled).
+ * @note HSI can not be stopped if it is used as system clock source. In this case,
+ * you have to select another source of the system clock then stop the HSI.
+ * @note After enabling the HSI, the application software should wait on HSIRDY
+ * flag to be set indicating that HSI clock is stable and can be used as
+ * system clock source.
+ * @param NewState: new state of the HSI.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator
+ * clock cycles.
+ * @retval None
+ */
+void RCC_HSICmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ *(__IO uint32_t *) CR_HSION_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Configures the External Low Speed oscillator (LSE).
+ * @note As the LSE is in the Backup domain and write access is denied to
+ * this domain after reset, you have to enable write access using
+ * PWR_BackupAccessCmd(ENABLE) function before to configure the LSE
+ * (to be done once after reset).
+ * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_Bypass), the application
+ * software should wait on LSERDY flag to be set indicating that LSE clock
+ * is stable and can be used to clock the RTC.
+ * @param RCC_LSE: specifies the new state of the LSE.
+ * This parameter can be one of the following values:
+ * @arg RCC_LSE_OFF: turn OFF the LSE oscillator, LSERDY flag goes low after
+ * 6 LSE oscillator clock cycles.
+ * @arg RCC_LSE_ON: turn ON the LSE oscillator
+ * @arg RCC_LSE_Bypass: LSE oscillator bypassed with external clock
+ * @retval None
+ */
+void RCC_LSEConfig(uint8_t RCC_LSE)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_LSE(RCC_LSE));
+
+ /* Reset LSEON and LSEBYP bits before configuring the LSE ------------------*/
+ /* Reset LSEON bit */
+ *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_OFF;
+
+ /* Reset LSEBYP bit */
+ *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_OFF;
+
+ /* Configure LSE (RCC_LSE_OFF is already covered by the code section above) */
+ switch (RCC_LSE)
+ {
+ case RCC_LSE_ON:
+ /* Set LSEON bit */
+ *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_ON;
+ break;
+ case RCC_LSE_Bypass:
+ /* Set LSEBYP and LSEON bits */
+ *(__IO uint8_t *) BDCR_ADDRESS = RCC_LSE_Bypass | RCC_LSE_ON;
+ break;
+ default:
+ break;
+ }
+}
+
+/**
+ * @brief Enables or disables the Internal Low Speed oscillator (LSI).
+ * @note After enabling the LSI, the application software should wait on
+ * LSIRDY flag to be set indicating that LSI clock is stable and can
+ * be used to clock the IWDG and/or the RTC.
+ * @note LSI can not be disabled if the IWDG is running.
+ * @param NewState: new state of the LSI.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator
+ * clock cycles.
+ * @retval None
+ */
+void RCC_LSICmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ *(__IO uint32_t *) CSR_LSION_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Configures the main PLL clock source, multiplication and division factors.
+ * @note This function must be used only when the main PLL is disabled.
+ *
+ * @param RCC_PLLSource: specifies the PLL entry clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_PLLSource_HSI: HSI oscillator clock selected as PLL clock entry
+ * @arg RCC_PLLSource_HSE: HSE oscillator clock selected as PLL clock entry
+ * @note This clock source (RCC_PLLSource) is common for the main PLL and PLLI2S.
+ *
+ * @param PLLM: specifies the division factor for PLL VCO input clock
+ * This parameter must be a number between 0 and 63.
+ * @note You have to set the PLLM parameter correctly to ensure that the VCO input
+ * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
+ * of 2 MHz to limit PLL jitter.
+ *
+ * @param PLLN: specifies the multiplication factor for PLL VCO output clock
+ * This parameter must be a number between 192 and 432.
+ * @note You have to set the PLLN parameter correctly to ensure that the VCO
+ * output frequency is between 192 and 432 MHz.
+ *
+ * @param PLLP: specifies the division factor for main system clock (SYSCLK)
+ * This parameter must be a number in the range {2, 4, 6, or 8}.
+ * @note You have to set the PLLP parameter correctly to not exceed 120 MHz on
+ * the System clock frequency.
+ *
+ * @param PLLQ: specifies the division factor for OTG FS, SDIO and RNG clocks
+ * This parameter must be a number between 4 and 15.
+ * @note If the USB OTG FS is used in your application, you have to set the
+ * PLLQ parameter correctly to have 48 MHz clock for the USB. However,
+ * the SDIO and RNG need a frequency lower than or equal to 48 MHz to work
+ * correctly.
+ *
+ * @retval None
+ */
+void RCC_PLLConfig(uint32_t RCC_PLLSource, uint32_t PLLM, uint32_t PLLN, uint32_t PLLP, uint32_t PLLQ)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_PLL_SOURCE(RCC_PLLSource));
+ assert_param(IS_RCC_PLLM_VALUE(PLLM));
+ assert_param(IS_RCC_PLLN_VALUE(PLLN));
+ assert_param(IS_RCC_PLLP_VALUE(PLLP));
+ assert_param(IS_RCC_PLLQ_VALUE(PLLQ));
+
+ RCC->PLLCFGR = PLLM | (PLLN << 6) | (((PLLP >> 1) -1) << 16) | (RCC_PLLSource) |
+ (PLLQ << 24);
+}
+
+/**
+ * @brief Enables or disables the main PLL.
+ * @note After enabling the main PLL, the application software should wait on
+ * PLLRDY flag to be set indicating that PLL clock is stable and can
+ * be used as system clock source.
+ * @note The main PLL can not be disabled if it is used as system clock source
+ * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes.
+ * @param NewState: new state of the main PLL. This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_PLLCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) CR_PLLON_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Configures the PLLI2S clock multiplication and division factors.
+ *
+ * @note PLLI2S is available only in Silicon RevisionB and RevisionY.
+ * @note This function must be used only when the PLLI2S is disabled.
+ * @note PLLI2S clock source is common with the main PLL (configured in
+ * RCC_PLLConfig function )
+ *
+ * @param PLLI2SN: specifies the multiplication factor for PLLI2S VCO output clock
+ * This parameter must be a number between 192 and 432.
+ * @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
+ * output frequency is between 192 and 432 MHz.
+ *
+ * @param PLLI2SR: specifies the division factor for I2S clock
+ * This parameter must be a number between 2 and 7.
+ * @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
+ * on the I2S clock frequency.
+ *
+ * @retval None
+ */
+void RCC_PLLI2SConfig(uint32_t PLLI2SN, uint32_t PLLI2SR)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_PLLI2SN_VALUE(PLLI2SN));
+ assert_param(IS_RCC_PLLI2SR_VALUE(PLLI2SR));
+
+ RCC->PLLI2SCFGR = (PLLI2SN << 6) | (PLLI2SR << 28);
+}
+
+/**
+ * @brief Enables or disables the PLLI2S.
+ * @note PLLI2S is available only in RevisionB and RevisionY
+ * @note The PLLI2S is disabled by hardware when entering STOP and STANDBY modes.
+ * @param NewState: new state of the PLLI2S. This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_PLLI2SCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) CR_PLLI2SON_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Enables or disables the Clock Security System.
+ * @note If a failure is detected on the HSE oscillator clock, this oscillator
+ * is automatically disabled and an interrupt is generated to inform the
+ * software about the failure (Clock Security System Interrupt, CSSI),
+ * allowing the MCU to perform rescue operations. The CSSI is linked to
+ * the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector.
+ * @param NewState: new state of the Clock Security System.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_ClockSecuritySystemCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) CR_CSSON_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Selects the clock source to output on MCO1 pin(PA8).
+ * @note PA8 should be configured in alternate function mode.
+ * @param RCC_MCO1Source: specifies the clock source to output.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1Source_HSI: HSI clock selected as MCO1 source
+ * @arg RCC_MCO1Source_LSE: LSE clock selected as MCO1 source
+ * @arg RCC_MCO1Source_HSE: HSE clock selected as MCO1 source
+ * @arg RCC_MCO1Source_PLLCLK: main PLL clock selected as MCO1 source
+ * @param RCC_MCO1Div: specifies the MCO1 prescaler.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1Div_1: no division applied to MCO1 clock
+ * @arg RCC_MCO1Div_2: division by 2 applied to MCO1 clock
+ * @arg RCC_MCO1Div_3: division by 3 applied to MCO1 clock
+ * @arg RCC_MCO1Div_4: division by 4 applied to MCO1 clock
+ * @arg RCC_MCO1Div_5: division by 5 applied to MCO1 clock
+ * @retval None
+ */
+void RCC_MCO1Config(uint32_t RCC_MCO1Source, uint32_t RCC_MCO1Div)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_MCO1SOURCE(RCC_MCO1Source));
+ assert_param(IS_RCC_MCO1DIV(RCC_MCO1Div));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear MCO1[1:0] and MCO1PRE[2:0] bits */
+ tmpreg &= CFGR_MCO1_RESET_MASK;
+
+ /* Select MCO1 clock source and prescaler */
+ tmpreg |= RCC_MCO1Source | RCC_MCO1Div;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+/**
+ * @brief Selects the clock source to output on MCO2 pin(PC9).
+ * @note PC9 should be configured in alternate function mode.
+ * @param RCC_MCO2Source: specifies the clock source to output.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO2Source_SYSCLK: System clock (SYSCLK) selected as MCO2 source
+ * @arg RCC_MCO2Source_PLLI2SCLK: PLLI2S clock selected as MCO2 source
+ * @arg RCC_MCO2Source_HSE: HSE clock selected as MCO2 source
+ * @arg RCC_MCO2Source_PLLCLK: main PLL clock selected as MCO2 source
+ * @param RCC_MCO2Div: specifies the MCO2 prescaler.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO2Div_1: no division applied to MCO2 clock
+ * @arg RCC_MCO2Div_2: division by 2 applied to MCO2 clock
+ * @arg RCC_MCO2Div_3: division by 3 applied to MCO2 clock
+ * @arg RCC_MCO2Div_4: division by 4 applied to MCO2 clock
+ * @arg RCC_MCO2Div_5: division by 5 applied to MCO2 clock
+ * @retval None
+ */
+void RCC_MCO2Config(uint32_t RCC_MCO2Source, uint32_t RCC_MCO2Div)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_MCO2SOURCE(RCC_MCO2Source));
+ assert_param(IS_RCC_MCO2DIV(RCC_MCO2Div));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear MCO2 and MCO2PRE[2:0] bits */
+ tmpreg &= CFGR_MCO2_RESET_MASK;
+
+ /* Select MCO2 clock source and prescaler */
+ tmpreg |= RCC_MCO2Source | RCC_MCO2Div;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Group2 System AHB and APB busses clocks configuration functions
+ * @brief System, AHB and APB busses clocks configuration functions
+ *
+@verbatim
+ ===============================================================================
+ System, AHB and APB busses clocks configuration functions
+ ===============================================================================
+
+ This section provide functions allowing to configure the System, AHB, APB1 and
+ APB2 busses clocks.
+
+ 1. Several clock sources can be used to drive the System clock (SYSCLK): HSI,
+ HSE and PLL.
+ The AHB clock (HCLK) is derived from System clock through configurable prescaler
+ and used to clock the CPU, memory and peripherals mapped on AHB bus (DMA, GPIO...).
+ APB1 (PCLK1) and APB2 (PCLK2) clocks are derived from AHB clock through
+ configurable prescalers and used to clock the peripherals mapped on these busses.
+ You can use "RCC_GetClocksFreq()" function to retrieve the frequencies of these clocks.
+
+@note All the peripheral clocks are derived from the System clock (SYSCLK) except:
+ - I2S: the I2S clock can be derived either from a specific PLL (PLLI2S) or
+ from an external clock mapped on the I2S_CKIN pin.
+ You have to use RCC_I2SCLKConfig() function to configure this clock.
+ - RTC: the RTC clock can be derived either from the LSI, LSE or HSE clock
+ divided by 2 to 31. You have to use RCC_RTCCLKConfig() and RCC_RTCCLKCmd()
+ functions to configure this clock.
+ - USB OTG FS, SDIO and RTC: USB OTG FS require a frequency equal to 48 MHz
+ to work correctly, while the SDIO require a frequency equal or lower than
+ to 48. This clock is derived of the main PLL through PLLQ divider.
+ - IWDG clock which is always the LSI clock.
+
+ 2. The maximum frequency of the SYSCLK and HCLK is 120 MHz, PCLK2 60 MHz and PCLK1 30 MHz.
+ Depending on the device voltage range, the maximum frequency should be
+ adapted accordingly:
+ +-------------------------------------------------------------------------------------+
+ | Latency | HCLK clock frequency (MHz) |
+ | |---------------------------------------------------------------------|
+ | | voltage range | voltage range | voltage range | voltage range |
+ | | 2.7 V - 3.6 V | 2.4 V - 2.7 V | 2.1 V - 2.4 V | 1.8 V - 2.1 V |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |0WS(1CPU cycle)|0 < HCLK <= 30 |0 < HCLK <= 24 |0 < HCLK <= 18 |0 < HCLK <= 16 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |1WS(2CPU cycle)|30 < HCLK <= 60 |24 < HCLK <= 48 |18 < HCLK <= 36 |16 < HCLK <= 32 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |2WS(3CPU cycle)|60 < HCLK <= 90 |48 < HCLK <= 72 |36 < HCLK <= 54 |32 < HCLK <= 48 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |3WS(4CPU cycle)|90 < HCLK <= 120|72 < HCLK <= 96 |54 < HCLK <= 72 |48 < HCLK <= 64 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |4WS(5CPU cycle)| NA |96 < HCLK <= 120|72 < HCLK <= 90 |64 < HCLK <= 80 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |5WS(6CPU cycle)| NA | NA |90 < HCLK <= 108 |80 < HCLK <= 96 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |6WS(7CPU cycle)| NA | NA |108 < HCLK <= 120|96 < HCLK <= 112 |
+ |---------------|----------------|----------------|-----------------|-----------------|
+ |7WS(8CPU cycle)| NA | NA | NA |112 < HCLK <= 120|
+ +-------------------------------------------------------------------------------------+
+
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the system clock (SYSCLK).
+ * @note The HSI is used (enabled by hardware) as system clock source after
+ * startup from Reset, wake-up from STOP and STANDBY mode, or in case
+ * of failure of the HSE used directly or indirectly as system clock
+ * (if the Clock Security System CSS is enabled).
+ * @note A switch from one clock source to another occurs only if the target
+ * clock source is ready (clock stable after startup delay or PLL locked).
+ * If a clock source which is not yet ready is selected, the switch will
+ * occur when the clock source will be ready.
+ * You can use RCC_GetSYSCLKSource() function to know which clock is
+ * currently used as system clock source.
+ * @param RCC_SYSCLKSource: specifies the clock source used as system clock.
+ * This parameter can be one of the following values:
+ * @arg RCC_SYSCLKSource_HSI: HSI selected as system clock source
+ * @arg RCC_SYSCLKSource_HSE: HSE selected as system clock source
+ * @arg RCC_SYSCLKSource_PLLCLK: PLL selected as system clock source
+ * @retval None
+ */
+void RCC_SYSCLKConfig(uint32_t RCC_SYSCLKSource)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_SYSCLK_SOURCE(RCC_SYSCLKSource));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear SW[1:0] bits */
+ tmpreg &= ~RCC_CFGR_SW;
+
+ /* Set SW[1:0] bits according to RCC_SYSCLKSource value */
+ tmpreg |= RCC_SYSCLKSource;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+/**
+ * @brief Returns the clock source used as system clock.
+ * @param None
+ * @retval The clock source used as system clock. The returned value can be one
+ * of the following:
+ * - 0x00: HSI used as system clock
+ * - 0x04: HSE used as system clock
+ * - 0x08: PLL used as system clock
+ */
+uint8_t RCC_GetSYSCLKSource(void)
+{
+ return ((uint8_t)(RCC->CFGR & RCC_CFGR_SWS));
+}
+
+/**
+ * @brief Configures the AHB clock (HCLK).
+ * @note Depending on the device voltage range, the software has to set correctly
+ * these bits to ensure that HCLK not exceed the maximum allowed frequency
+ * (for more details refer to section above
+ * "CPU, AHB and APB busses clocks configuration functions")
+ * @param RCC_SYSCLK: defines the AHB clock divider. This clock is derived from
+ * the system clock (SYSCLK).
+ * This parameter can be one of the following values:
+ * @arg RCC_SYSCLK_Div1: AHB clock = SYSCLK
+ * @arg RCC_SYSCLK_Div2: AHB clock = SYSCLK/2
+ * @arg RCC_SYSCLK_Div4: AHB clock = SYSCLK/4
+ * @arg RCC_SYSCLK_Div8: AHB clock = SYSCLK/8
+ * @arg RCC_SYSCLK_Div16: AHB clock = SYSCLK/16
+ * @arg RCC_SYSCLK_Div64: AHB clock = SYSCLK/64
+ * @arg RCC_SYSCLK_Div128: AHB clock = SYSCLK/128
+ * @arg RCC_SYSCLK_Div256: AHB clock = SYSCLK/256
+ * @arg RCC_SYSCLK_Div512: AHB clock = SYSCLK/512
+ * @retval None
+ */
+void RCC_HCLKConfig(uint32_t RCC_SYSCLK)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_HCLK(RCC_SYSCLK));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear HPRE[3:0] bits */
+ tmpreg &= ~RCC_CFGR_HPRE;
+
+ /* Set HPRE[3:0] bits according to RCC_SYSCLK value */
+ tmpreg |= RCC_SYSCLK;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+
+/**
+ * @brief Configures the Low Speed APB clock (PCLK1).
+ * @param RCC_HCLK: defines the APB1 clock divider. This clock is derived from
+ * the AHB clock (HCLK).
+ * This parameter can be one of the following values:
+ * @arg RCC_HCLK_Div1: APB1 clock = HCLK
+ * @arg RCC_HCLK_Div2: APB1 clock = HCLK/2
+ * @arg RCC_HCLK_Div4: APB1 clock = HCLK/4
+ * @arg RCC_HCLK_Div8: APB1 clock = HCLK/8
+ * @arg RCC_HCLK_Div16: APB1 clock = HCLK/16
+ * @retval None
+ */
+void RCC_PCLK1Config(uint32_t RCC_HCLK)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_PCLK(RCC_HCLK));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear PPRE1[2:0] bits */
+ tmpreg &= ~RCC_CFGR_PPRE1;
+
+ /* Set PPRE1[2:0] bits according to RCC_HCLK value */
+ tmpreg |= RCC_HCLK;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+/**
+ * @brief Configures the High Speed APB clock (PCLK2).
+ * @param RCC_HCLK: defines the APB2 clock divider. This clock is derived from
+ * the AHB clock (HCLK).
+ * This parameter can be one of the following values:
+ * @arg RCC_HCLK_Div1: APB2 clock = HCLK
+ * @arg RCC_HCLK_Div2: APB2 clock = HCLK/2
+ * @arg RCC_HCLK_Div4: APB2 clock = HCLK/4
+ * @arg RCC_HCLK_Div8: APB2 clock = HCLK/8
+ * @arg RCC_HCLK_Div16: APB2 clock = HCLK/16
+ * @retval None
+ */
+void RCC_PCLK2Config(uint32_t RCC_HCLK)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_PCLK(RCC_HCLK));
+
+ tmpreg = RCC->CFGR;
+
+ /* Clear PPRE2[2:0] bits */
+ tmpreg &= ~RCC_CFGR_PPRE2;
+
+ /* Set PPRE2[2:0] bits according to RCC_HCLK value */
+ tmpreg |= RCC_HCLK << 3;
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+}
+
+/**
+ * @brief Returns the frequencies of different on chip clocks; SYSCLK, HCLK,
+ * PCLK1 and PCLK2.
+ *
+ * @note The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
+ * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**)
+ * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied/divided by the PLL factors.
+ * @note (*) HSI_VALUE is a constant defined in stm32f4xx.h file (default value
+ * 16 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ * @note (**) HSE_VALUE is a constant defined in stm32f4xx.h file (default value
+ * 25 MHz), user has to ensure that HSE_VALUE is same as the real
+ * frequency of the crystal used. Otherwise, this function may
+ * have wrong result.
+ *
+ * @note The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ *
+ * @param RCC_Clocks: pointer to a RCC_ClocksTypeDef structure which will hold
+ * the clocks frequencies.
+ *
+ * @note This function can be used by the user application to compute the
+ * baudrate for the communication peripherals or configure other parameters.
+ * @note Each time SYSCLK, HCLK, PCLK1 and/or PCLK2 clock changes, this function
+ * must be called to update the structure's field. Otherwise, any
+ * configuration based on this function will be incorrect.
+ *
+ * @retval None
+ */
+void RCC_GetClocksFreq(RCC_ClocksTypeDef* RCC_Clocks)
+{
+ uint32_t tmp = 0, presc = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+ switch (tmp)
+ {
+ case 0x00: /* HSI used as system clock source */
+ RCC_Clocks->SYSCLK_Frequency = HSI_VALUE;
+ break;
+ case 0x04: /* HSE used as system clock source */
+ RCC_Clocks->SYSCLK_Frequency = HSE_VALUE;
+ break;
+ case 0x08: /* PLL used as system clock source */
+
+ /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN
+ SYSCLK = PLL_VCO / PLLP
+ */
+ pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
+ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+
+ if (pllsource != 0)
+ {
+ /* HSE used as PLL clock source */
+ pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+ else
+ {
+ /* HSI used as PLL clock source */
+ pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+
+ pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
+ RCC_Clocks->SYSCLK_Frequency = pllvco/pllp;
+ break;
+ default:
+ RCC_Clocks->SYSCLK_Frequency = HSI_VALUE;
+ break;
+ }
+ /* Compute HCLK, PCLK1 and PCLK2 clocks frequencies ------------------------*/
+
+ /* Get HCLK prescaler */
+ tmp = RCC->CFGR & RCC_CFGR_HPRE;
+ tmp = tmp >> 4;
+ presc = APBAHBPrescTable[tmp];
+ /* HCLK clock frequency */
+ RCC_Clocks->HCLK_Frequency = RCC_Clocks->SYSCLK_Frequency >> presc;
+
+ /* Get PCLK1 prescaler */
+ tmp = RCC->CFGR & RCC_CFGR_PPRE1;
+ tmp = tmp >> 10;
+ presc = APBAHBPrescTable[tmp];
+ /* PCLK1 clock frequency */
+ RCC_Clocks->PCLK1_Frequency = RCC_Clocks->HCLK_Frequency >> presc;
+
+ /* Get PCLK2 prescaler */
+ tmp = RCC->CFGR & RCC_CFGR_PPRE2;
+ tmp = tmp >> 13;
+ presc = APBAHBPrescTable[tmp];
+ /* PCLK2 clock frequency */
+ RCC_Clocks->PCLK2_Frequency = RCC_Clocks->HCLK_Frequency >> presc;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Group3 Peripheral clocks configuration functions
+ * @brief Peripheral clocks configuration functions
+ *
+@verbatim
+ ===============================================================================
+ Peripheral clocks configuration functions
+ ===============================================================================
+
+ This section provide functions allowing to configure the Peripheral clocks.
+
+ 1. The RTC clock which is derived from the LSI, LSE or HSE clock divided by 2 to 31.
+
+ 2. After restart from Reset or wakeup from STANDBY, all peripherals are off
+ except internal SRAM, Flash and JTAG. Before to start using a peripheral you
+ have to enable its interface clock. You can do this using RCC_AHBPeriphClockCmd()
+ , RCC_APB2PeriphClockCmd() and RCC_APB1PeriphClockCmd() functions.
+
+ 3. To reset the peripherals configuration (to the default state after device reset)
+ you can use RCC_AHBPeriphResetCmd(), RCC_APB2PeriphResetCmd() and
+ RCC_APB1PeriphResetCmd() functions.
+
+ 4. To further reduce power consumption in SLEEP mode the peripheral clocks can
+ be disabled prior to executing the WFI or WFE instructions. You can do this
+ using RCC_AHBPeriphClockLPModeCmd(), RCC_APB2PeriphClockLPModeCmd() and
+ RCC_APB1PeriphClockLPModeCmd() functions.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the RTC clock (RTCCLK).
+ * @note As the RTC clock configuration bits are in the Backup domain and write
+ * access is denied to this domain after reset, you have to enable write
+ * access using PWR_BackupAccessCmd(ENABLE) function before to configure
+ * the RTC clock source (to be done once after reset).
+ * @note Once the RTC clock is configured it can't be changed unless the
+ * Backup domain is reset using RCC_BackupResetCmd() function, or by
+ * a Power On Reset (POR).
+ *
+ * @param RCC_RTCCLKSource: specifies the RTC clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_RTCCLKSource_LSE: LSE selected as RTC clock
+ * @arg RCC_RTCCLKSource_LSI: LSI selected as RTC clock
+ * @arg RCC_RTCCLKSource_HSE_Divx: HSE clock divided by x selected
+ * as RTC clock, where x:[2,31]
+ *
+ * @note If the LSE or LSI is used as RTC clock source, the RTC continues to
+ * work in STOP and STANDBY modes, and can be used as wakeup source.
+ * However, when the HSE clock is used as RTC clock source, the RTC
+ * cannot be used in STOP and STANDBY modes.
+ * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as
+ * RTC clock source).
+ *
+ * @retval None
+ */
+void RCC_RTCCLKConfig(uint32_t RCC_RTCCLKSource)
+{
+ uint32_t tmpreg = 0;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_RTCCLK_SOURCE(RCC_RTCCLKSource));
+
+ if ((RCC_RTCCLKSource & 0x00000300) == 0x00000300)
+ { /* If HSE is selected as RTC clock source, configure HSE division factor for RTC clock */
+ tmpreg = RCC->CFGR;
+
+ /* Clear RTCPRE[4:0] bits */
+ tmpreg &= ~RCC_CFGR_RTCPRE;
+
+ /* Configure HSE division factor for RTC clock */
+ tmpreg |= (RCC_RTCCLKSource & 0xFFFFCFF);
+
+ /* Store the new value */
+ RCC->CFGR = tmpreg;
+ }
+
+ /* Select the RTC clock source */
+ RCC->BDCR |= (RCC_RTCCLKSource & 0x00000FFF);
+}
+
+/**
+ * @brief Enables or disables the RTC clock.
+ * @note This function must be used only after the RTC clock source was selected
+ * using the RCC_RTCCLKConfig function.
+ * @param NewState: new state of the RTC clock. This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_RTCCLKCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ *(__IO uint32_t *) BDCR_RTCEN_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Forces or releases the Backup domain reset.
+ * @note This function resets the RTC peripheral (including the backup registers)
+ * and the RTC clock source selection in RCC_CSR register.
+ * @note The BKPSRAM is not affected by this reset.
+ * @param NewState: new state of the Backup domain reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_BackupResetCmd(FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ *(__IO uint32_t *) BDCR_BDRST_BB = (uint32_t)NewState;
+}
+
+/**
+ * @brief Configures the I2S clock source (I2SCLK).
+ *
+ * @note This function must be called before enabling the I2S APB clock.
+ * @note This function applies only to Silicon RevisionB and RevisionY.
+ *
+ * @param RCC_I2SCLKSource: specifies the I2S clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_I2S2CLKSource_PLLI2S: PLLI2S clock used as I2S clock source
+ * @arg RCC_I2S2CLKSource_Ext: External clock mapped on the I2S_CKIN pin
+ * used as I2S clock source
+ * @retval None
+ */
+void RCC_I2SCLKConfig(uint32_t RCC_I2SCLKSource)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_I2SCLK_SOURCE(RCC_I2SCLKSource));
+
+ *(__IO uint32_t *) CFGR_I2SSRC_BB = RCC_I2SCLKSource;
+}
+
+/**
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @param RCC_AHBPeriph: specifies the AHB1 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB1Periph_GPIOA: GPIOA clock
+ * @arg RCC_AHB1Periph_GPIOB: GPIOB clock
+ * @arg RCC_AHB1Periph_GPIOC: GPIOC clock
+ * @arg RCC_AHB1Periph_GPIOD: GPIOD clock
+ * @arg RCC_AHB1Periph_GPIOE: GPIOE clock
+ * @arg RCC_AHB1Periph_GPIOF: GPIOF clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOI: GPIOI clock
+ * @arg RCC_AHB1Periph_CRC: CRC clock
+ * @arg RCC_AHB1Periph_BKPSRAM: BKPSRAM interface clock
+ * @arg RCC_AHB1Periph_DMA1: DMA1 clock
+ * @arg RCC_AHB1Periph_DMA2: DMA2 clock
+ * @arg RCC_AHB1Periph_ETH_MAC: Ethernet MAC clock
+ * @arg RCC_AHB1Periph_ETH_MAC_Tx: Ethernet Transmission clock
+ * @arg RCC_AHB1Periph_ETH_MAC_Rx: Ethernet Reception clock
+ * @arg RCC_AHB1Periph_ETH_MAC_PTP: Ethernet PTP clock
+ * @arg RCC_AHB1Periph_OTG_HS: USB OTG HS clock
+ * @arg RCC_AHB1Periph_OTG_HS_ULPI: USB OTG HS ULPI clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB1PeriphClockCmd(uint32_t RCC_AHB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB1_CLOCK_PERIPH(RCC_AHB1Periph));
+
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->AHB1ENR |= RCC_AHB1Periph;
+ }
+ else
+ {
+ RCC->AHB1ENR &= ~RCC_AHB1Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @param RCC_AHBPeriph: specifies the AHB2 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB2Periph_DCMI: DCMI clock
+ * @arg RCC_AHB2Periph_CRYP: CRYP clock
+ * @arg RCC_AHB2Periph_HASH: HASH clock
+ * @arg RCC_AHB2Periph_RNG: RNG clock
+ * @arg RCC_AHB2Periph_OTG_FS: USB OTG FS clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB2PeriphClockCmd(uint32_t RCC_AHB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB2_PERIPH(RCC_AHB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->AHB2ENR |= RCC_AHB2Periph;
+ }
+ else
+ {
+ RCC->AHB2ENR &= ~RCC_AHB2Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the AHB3 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @param RCC_AHBPeriph: specifies the AHB3 peripheral to gates its clock.
+ * This parameter must be: RCC_AHB3Periph_FSMC
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB3PeriphClockCmd(uint32_t RCC_AHB3Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB3_PERIPH(RCC_AHB3Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->AHB3ENR |= RCC_AHB3Periph;
+ }
+ else
+ {
+ RCC->AHB3ENR &= ~RCC_AHB3Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @param RCC_APB1Periph: specifies the APB1 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB1Periph_TIM2: TIM2 clock
+ * @arg RCC_APB1Periph_TIM3: TIM3 clock
+ * @arg RCC_APB1Periph_TIM4: TIM4 clock
+ * @arg RCC_APB1Periph_TIM5: TIM5 clock
+ * @arg RCC_APB1Periph_TIM6: TIM6 clock
+ * @arg RCC_APB1Periph_TIM7: TIM7 clock
+ * @arg RCC_APB1Periph_TIM12: TIM12 clock
+ * @arg RCC_APB1Periph_TIM13: TIM13 clock
+ * @arg RCC_APB1Periph_TIM14: TIM14 clock
+ * @arg RCC_APB1Periph_WWDG: WWDG clock
+ * @arg RCC_APB1Periph_SPI2: SPI2 clock
+ * @arg RCC_APB1Periph_SPI3: SPI3 clock
+ * @arg RCC_APB1Periph_USART2: USART2 clock
+ * @arg RCC_APB1Periph_USART3: USART3 clock
+ * @arg RCC_APB1Periph_UART4: UART4 clock
+ * @arg RCC_APB1Periph_UART5: UART5 clock
+ * @arg RCC_APB1Periph_I2C1: I2C1 clock
+ * @arg RCC_APB1Periph_I2C2: I2C2 clock
+ * @arg RCC_APB1Periph_I2C3: I2C3 clock
+ * @arg RCC_APB1Periph_CAN1: CAN1 clock
+ * @arg RCC_APB1Periph_CAN2: CAN2 clock
+ * @arg RCC_APB1Periph_PWR: PWR clock
+ * @arg RCC_APB1Periph_DAC: DAC clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB1PeriphClockCmd(uint32_t RCC_APB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB1_PERIPH(RCC_APB1Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->APB1ENR |= RCC_APB1Periph;
+ }
+ else
+ {
+ RCC->APB1ENR &= ~RCC_APB1Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the High Speed APB (APB2) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @param RCC_APB2Periph: specifies the APB2 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB2Periph_TIM1: TIM1 clock
+ * @arg RCC_APB2Periph_TIM8: TIM8 clock
+ * @arg RCC_APB2Periph_USART1: USART1 clock
+ * @arg RCC_APB2Periph_USART6: USART6 clock
+ * @arg RCC_APB2Periph_ADC1: ADC1 clock
+ * @arg RCC_APB2Periph_ADC2: ADC2 clock
+ * @arg RCC_APB2Periph_ADC3: ADC3 clock
+ * @arg RCC_APB2Periph_SDIO: SDIO clock
+ * @arg RCC_APB2Periph_SPI1: SPI1 clock
+ * @arg RCC_APB2Periph_SYSCFG: SYSCFG clock
+ * @arg RCC_APB2Periph_TIM9: TIM9 clock
+ * @arg RCC_APB2Periph_TIM10: TIM10 clock
+ * @arg RCC_APB2Periph_TIM11: TIM11 clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB2PeriphClockCmd(uint32_t RCC_APB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB2_PERIPH(RCC_APB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->APB2ENR |= RCC_APB2Periph;
+ }
+ else
+ {
+ RCC->APB2ENR &= ~RCC_APB2Periph;
+ }
+}
+
+/**
+ * @brief Forces or releases AHB1 peripheral reset.
+ * @param RCC_AHB1Periph: specifies the AHB1 peripheral to reset.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB1Periph_GPIOA: GPIOA clock
+ * @arg RCC_AHB1Periph_GPIOB: GPIOB clock
+ * @arg RCC_AHB1Periph_GPIOC: GPIOC clock
+ * @arg RCC_AHB1Periph_GPIOD: GPIOD clock
+ * @arg RCC_AHB1Periph_GPIOE: GPIOE clock
+ * @arg RCC_AHB1Periph_GPIOF: GPIOF clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOI: GPIOI clock
+ * @arg RCC_AHB1Periph_CRC: CRC clock
+ * @arg RCC_AHB1Periph_DMA1: DMA1 clock
+ * @arg RCC_AHB1Periph_DMA2: DMA2 clock
+ * @arg RCC_AHB1Periph_ETH_MAC: Ethernet MAC clock
+ * @arg RCC_AHB1Periph_OTG_HS: USB OTG HS clock
+ *
+ * @param NewState: new state of the specified peripheral reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB1PeriphResetCmd(uint32_t RCC_AHB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB1_RESET_PERIPH(RCC_AHB1Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->AHB1RSTR |= RCC_AHB1Periph;
+ }
+ else
+ {
+ RCC->AHB1RSTR &= ~RCC_AHB1Periph;
+ }
+}
+
+/**
+ * @brief Forces or releases AHB2 peripheral reset.
+ * @param RCC_AHB2Periph: specifies the AHB2 peripheral to reset.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB2Periph_DCMI: DCMI clock
+ * @arg RCC_AHB2Periph_CRYP: CRYP clock
+ * @arg RCC_AHB2Periph_HASH: HASH clock
+ * @arg RCC_AHB2Periph_RNG: RNG clock
+ * @arg RCC_AHB2Periph_OTG_FS: USB OTG FS clock
+ * @param NewState: new state of the specified peripheral reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB2PeriphResetCmd(uint32_t RCC_AHB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB2_PERIPH(RCC_AHB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->AHB2RSTR |= RCC_AHB2Periph;
+ }
+ else
+ {
+ RCC->AHB2RSTR &= ~RCC_AHB2Periph;
+ }
+}
+
+/**
+ * @brief Forces or releases AHB3 peripheral reset.
+ * @param RCC_AHB3Periph: specifies the AHB3 peripheral to reset.
+ * This parameter must be: RCC_AHB3Periph_FSMC
+ * @param NewState: new state of the specified peripheral reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB3PeriphResetCmd(uint32_t RCC_AHB3Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB3_PERIPH(RCC_AHB3Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+ if (NewState != DISABLE)
+ {
+ RCC->AHB3RSTR |= RCC_AHB3Periph;
+ }
+ else
+ {
+ RCC->AHB3RSTR &= ~RCC_AHB3Periph;
+ }
+}
+
+/**
+ * @brief Forces or releases Low Speed APB (APB1) peripheral reset.
+ * @param RCC_APB1Periph: specifies the APB1 peripheral to reset.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB1Periph_TIM2: TIM2 clock
+ * @arg RCC_APB1Periph_TIM3: TIM3 clock
+ * @arg RCC_APB1Periph_TIM4: TIM4 clock
+ * @arg RCC_APB1Periph_TIM5: TIM5 clock
+ * @arg RCC_APB1Periph_TIM6: TIM6 clock
+ * @arg RCC_APB1Periph_TIM7: TIM7 clock
+ * @arg RCC_APB1Periph_TIM12: TIM12 clock
+ * @arg RCC_APB1Periph_TIM13: TIM13 clock
+ * @arg RCC_APB1Periph_TIM14: TIM14 clock
+ * @arg RCC_APB1Periph_WWDG: WWDG clock
+ * @arg RCC_APB1Periph_SPI2: SPI2 clock
+ * @arg RCC_APB1Periph_SPI3: SPI3 clock
+ * @arg RCC_APB1Periph_USART2: USART2 clock
+ * @arg RCC_APB1Periph_USART3: USART3 clock
+ * @arg RCC_APB1Periph_UART4: UART4 clock
+ * @arg RCC_APB1Periph_UART5: UART5 clock
+ * @arg RCC_APB1Periph_I2C1: I2C1 clock
+ * @arg RCC_APB1Periph_I2C2: I2C2 clock
+ * @arg RCC_APB1Periph_I2C3: I2C3 clock
+ * @arg RCC_APB1Periph_CAN1: CAN1 clock
+ * @arg RCC_APB1Periph_CAN2: CAN2 clock
+ * @arg RCC_APB1Periph_PWR: PWR clock
+ * @arg RCC_APB1Periph_DAC: DAC clock
+ * @param NewState: new state of the specified peripheral reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB1PeriphResetCmd(uint32_t RCC_APB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB1_PERIPH(RCC_APB1Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->APB1RSTR |= RCC_APB1Periph;
+ }
+ else
+ {
+ RCC->APB1RSTR &= ~RCC_APB1Periph;
+ }
+}
+
+/**
+ * @brief Forces or releases High Speed APB (APB2) peripheral reset.
+ * @param RCC_APB2Periph: specifies the APB2 peripheral to reset.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB2Periph_TIM1: TIM1 clock
+ * @arg RCC_APB2Periph_TIM8: TIM8 clock
+ * @arg RCC_APB2Periph_USART1: USART1 clock
+ * @arg RCC_APB2Periph_USART6: USART6 clock
+ * @arg RCC_APB2Periph_ADC1: ADC1 clock
+ * @arg RCC_APB2Periph_ADC2: ADC2 clock
+ * @arg RCC_APB2Periph_ADC3: ADC3 clock
+ * @arg RCC_APB2Periph_SDIO: SDIO clock
+ * @arg RCC_APB2Periph_SPI1: SPI1 clock
+ * @arg RCC_APB2Periph_SYSCFG: SYSCFG clock
+ * @arg RCC_APB2Periph_TIM9: TIM9 clock
+ * @arg RCC_APB2Periph_TIM10: TIM10 clock
+ * @arg RCC_APB2Periph_TIM11: TIM11 clock
+ * @param NewState: new state of the specified peripheral reset.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB2PeriphResetCmd(uint32_t RCC_APB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB2_RESET_PERIPH(RCC_APB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->APB2RSTR |= RCC_APB2Periph;
+ }
+ else
+ {
+ RCC->APB2RSTR &= ~RCC_APB2Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @param RCC_AHBPeriph: specifies the AHB1 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB1Periph_GPIOA: GPIOA clock
+ * @arg RCC_AHB1Periph_GPIOB: GPIOB clock
+ * @arg RCC_AHB1Periph_GPIOC: GPIOC clock
+ * @arg RCC_AHB1Periph_GPIOD: GPIOD clock
+ * @arg RCC_AHB1Periph_GPIOE: GPIOE clock
+ * @arg RCC_AHB1Periph_GPIOF: GPIOF clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOG: GPIOG clock
+ * @arg RCC_AHB1Periph_GPIOI: GPIOI clock
+ * @arg RCC_AHB1Periph_CRC: CRC clock
+ * @arg RCC_AHB1Periph_BKPSRAM: BKPSRAM interface clock
+ * @arg RCC_AHB1Periph_DMA1: DMA1 clock
+ * @arg RCC_AHB1Periph_DMA2: DMA2 clock
+ * @arg RCC_AHB1Periph_ETH_MAC: Ethernet MAC clock
+ * @arg RCC_AHB1Periph_ETH_MAC_Tx: Ethernet Transmission clock
+ * @arg RCC_AHB1Periph_ETH_MAC_Rx: Ethernet Reception clock
+ * @arg RCC_AHB1Periph_ETH_MAC_PTP: Ethernet PTP clock
+ * @arg RCC_AHB1Periph_OTG_HS: USB OTG HS clock
+ * @arg RCC_AHB1Periph_OTG_HS_ULPI: USB OTG HS ULPI clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB1PeriphClockLPModeCmd(uint32_t RCC_AHB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB1_LPMODE_PERIPH(RCC_AHB1Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->AHB1LPENR |= RCC_AHB1Periph;
+ }
+ else
+ {
+ RCC->AHB1LPENR &= ~RCC_AHB1Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @param RCC_AHBPeriph: specifies the AHB2 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_AHB2Periph_DCMI: DCMI clock
+ * @arg RCC_AHB2Periph_CRYP: CRYP clock
+ * @arg RCC_AHB2Periph_HASH: HASH clock
+ * @arg RCC_AHB2Periph_RNG: RNG clock
+ * @arg RCC_AHB2Periph_OTG_FS: USB OTG FS clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB2PeriphClockLPModeCmd(uint32_t RCC_AHB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB2_PERIPH(RCC_AHB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->AHB2LPENR |= RCC_AHB2Periph;
+ }
+ else
+ {
+ RCC->AHB2LPENR &= ~RCC_AHB2Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the AHB3 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @param RCC_AHBPeriph: specifies the AHB3 peripheral to gates its clock.
+ * This parameter must be: RCC_AHB3Periph_FSMC
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_AHB3PeriphClockLPModeCmd(uint32_t RCC_AHB3Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_AHB3_PERIPH(RCC_AHB3Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->AHB3LPENR |= RCC_AHB3Periph;
+ }
+ else
+ {
+ RCC->AHB3LPENR &= ~RCC_AHB3Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the APB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @param RCC_APB1Periph: specifies the APB1 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB1Periph_TIM2: TIM2 clock
+ * @arg RCC_APB1Periph_TIM3: TIM3 clock
+ * @arg RCC_APB1Periph_TIM4: TIM4 clock
+ * @arg RCC_APB1Periph_TIM5: TIM5 clock
+ * @arg RCC_APB1Periph_TIM6: TIM6 clock
+ * @arg RCC_APB1Periph_TIM7: TIM7 clock
+ * @arg RCC_APB1Periph_TIM12: TIM12 clock
+ * @arg RCC_APB1Periph_TIM13: TIM13 clock
+ * @arg RCC_APB1Periph_TIM14: TIM14 clock
+ * @arg RCC_APB1Periph_WWDG: WWDG clock
+ * @arg RCC_APB1Periph_SPI2: SPI2 clock
+ * @arg RCC_APB1Periph_SPI3: SPI3 clock
+ * @arg RCC_APB1Periph_USART2: USART2 clock
+ * @arg RCC_APB1Periph_USART3: USART3 clock
+ * @arg RCC_APB1Periph_UART4: UART4 clock
+ * @arg RCC_APB1Periph_UART5: UART5 clock
+ * @arg RCC_APB1Periph_I2C1: I2C1 clock
+ * @arg RCC_APB1Periph_I2C2: I2C2 clock
+ * @arg RCC_APB1Periph_I2C3: I2C3 clock
+ * @arg RCC_APB1Periph_CAN1: CAN1 clock
+ * @arg RCC_APB1Periph_CAN2: CAN2 clock
+ * @arg RCC_APB1Periph_PWR: PWR clock
+ * @arg RCC_APB1Periph_DAC: DAC clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB1PeriphClockLPModeCmd(uint32_t RCC_APB1Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB1_PERIPH(RCC_APB1Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->APB1LPENR |= RCC_APB1Periph;
+ }
+ else
+ {
+ RCC->APB1LPENR &= ~RCC_APB1Periph;
+ }
+}
+
+/**
+ * @brief Enables or disables the APB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @param RCC_APB2Periph: specifies the APB2 peripheral to gates its clock.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_APB2Periph_TIM1: TIM1 clock
+ * @arg RCC_APB2Periph_TIM8: TIM8 clock
+ * @arg RCC_APB2Periph_USART1: USART1 clock
+ * @arg RCC_APB2Periph_USART6: USART6 clock
+ * @arg RCC_APB2Periph_ADC1: ADC1 clock
+ * @arg RCC_APB2Periph_ADC2: ADC2 clock
+ * @arg RCC_APB2Periph_ADC3: ADC3 clock
+ * @arg RCC_APB2Periph_SDIO: SDIO clock
+ * @arg RCC_APB2Periph_SPI1: SPI1 clock
+ * @arg RCC_APB2Periph_SYSCFG: SYSCFG clock
+ * @arg RCC_APB2Periph_TIM9: TIM9 clock
+ * @arg RCC_APB2Periph_TIM10: TIM10 clock
+ * @arg RCC_APB2Periph_TIM11: TIM11 clock
+ * @param NewState: new state of the specified peripheral clock.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_APB2PeriphClockLPModeCmd(uint32_t RCC_APB2Periph, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_APB2_PERIPH(RCC_APB2Periph));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ RCC->APB2LPENR |= RCC_APB2Periph;
+ }
+ else
+ {
+ RCC->APB2LPENR &= ~RCC_APB2Periph;
+ }
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Group4 Interrupts and flags management functions
+ * @brief Interrupts and flags management functions
+ *
+@verbatim
+ ===============================================================================
+ Interrupts and flags management functions
+ ===============================================================================
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables or disables the specified RCC interrupts.
+ * @param RCC_IT: specifies the RCC interrupt sources to be enabled or disabled.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt
+ * @param NewState: new state of the specified RCC interrupts.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+void RCC_ITConfig(uint8_t RCC_IT, FunctionalState NewState)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_IT(RCC_IT));
+ assert_param(IS_FUNCTIONAL_STATE(NewState));
+ if (NewState != DISABLE)
+ {
+ /* Perform Byte access to RCC_CIR[14:8] bits to enable the selected interrupts */
+ *(__IO uint8_t *) CIR_BYTE2_ADDRESS |= RCC_IT;
+ }
+ else
+ {
+ /* Perform Byte access to RCC_CIR[14:8] bits to disable the selected interrupts */
+ *(__IO uint8_t *) CIR_BYTE2_ADDRESS &= (uint8_t)~RCC_IT;
+ }
+}
+
+/**
+ * @brief Checks whether the specified RCC flag is set or not.
+ * @param RCC_FLAG: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready
+ * @arg RCC_FLAG_HSERDY: HSE oscillator clock ready
+ * @arg RCC_FLAG_PLLRDY: main PLL clock ready
+ * @arg RCC_FLAG_PLLI2SRDY: PLLI2S clock ready
+ * @arg RCC_FLAG_LSERDY: LSE oscillator clock ready
+ * @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready
+ * @arg RCC_FLAG_BORRST: POR/PDR or BOR reset
+ * @arg RCC_FLAG_PINRST: Pin reset
+ * @arg RCC_FLAG_PORRST: POR/PDR reset
+ * @arg RCC_FLAG_SFTRST: Software reset
+ * @arg RCC_FLAG_IWDGRST: Independent Watchdog reset
+ * @arg RCC_FLAG_WWDGRST: Window Watchdog reset
+ * @arg RCC_FLAG_LPWRRST: Low Power reset
+ * @retval The new state of RCC_FLAG (SET or RESET).
+ */
+FlagStatus RCC_GetFlagStatus(uint8_t RCC_FLAG)
+{
+ uint32_t tmp = 0;
+ uint32_t statusreg = 0;
+ FlagStatus bitstatus = RESET;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_FLAG(RCC_FLAG));
+
+ /* Get the RCC register index */
+ tmp = RCC_FLAG >> 5;
+ if (tmp == 1) /* The flag to check is in CR register */
+ {
+ statusreg = RCC->CR;
+ }
+ else if (tmp == 2) /* The flag to check is in BDCR register */
+ {
+ statusreg = RCC->BDCR;
+ }
+ else /* The flag to check is in CSR register */
+ {
+ statusreg = RCC->CSR;
+ }
+
+ /* Get the flag position */
+ tmp = RCC_FLAG & FLAG_MASK;
+ if ((statusreg & ((uint32_t)1 << tmp)) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ /* Return the flag status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the RCC reset flags.
+ * The reset flags are: RCC_FLAG_PINRST, RCC_FLAG_PORRST, RCC_FLAG_SFTRST,
+ * RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST, RCC_FLAG_LPWRRST
+ * @param None
+ * @retval None
+ */
+void RCC_ClearFlag(void)
+{
+ /* Set RMVF bit to clear the reset flags */
+ RCC->CSR |= RCC_CSR_RMVF;
+}
+
+/**
+ * @brief Checks whether the specified RCC interrupt has occurred or not.
+ * @param RCC_IT: specifies the RCC interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt
+ * @arg RCC_IT_CSS: Clock Security System interrupt
+ * @retval The new state of RCC_IT (SET or RESET).
+ */
+ITStatus RCC_GetITStatus(uint8_t RCC_IT)
+{
+ ITStatus bitstatus = RESET;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_GET_IT(RCC_IT));
+
+ /* Check the status of the specified RCC interrupt */
+ if ((RCC->CIR & RCC_IT) != (uint32_t)RESET)
+ {
+ bitstatus = SET;
+ }
+ else
+ {
+ bitstatus = RESET;
+ }
+ /* Return the RCC_IT status */
+ return bitstatus;
+}
+
+/**
+ * @brief Clears the RCC's interrupt pending bits.
+ * @param RCC_IT: specifies the interrupt pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt
+ * @arg RCC_IT_CSS: Clock Security System interrupt
+ * @retval None
+ */
+void RCC_ClearITPendingBit(uint8_t RCC_IT)
+{
+ /* Check the parameters */
+ assert_param(IS_RCC_CLEAR_IT(RCC_IT));
+
+ /* Perform Byte access to RCC_CIR[23:16] bits to clear the selected interrupt
+ pending bits */
+ *(__IO uint8_t *) CIR_BYTE3_ADDRESS = RCC_IT;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/