kits have an onboard chip that translates USB commands sent by the host PC into
JTAG commands. This chip is called STLINK, which is confusing since the software
has the same name. It comes into 2 versions (STLINK v1 and v2). From a software
-point of view, those version differ only in the transport layer used to communicate
+point of view, those versions differ only in the transport layer used to communicate
(v1 uses SCSI passthru commands, while v2 uses raw USB).
+
+\paragraph{}
+Before continuing, the following dependencies must be met:
+\begin{itemize}
+\item libusb-1.0
+\item libsgutils2 (optionnal)
+\end{itemize}
+
+\paragraph{}
+STLINK should run on any system meeting the above constraints.
+
\paragraph{}
The STLINK software source code is retrieved using:\\
\begin{small}
\begin{lstlisting}[frame=tb]
-git clone https://github.com/texane/stlink stlink.git
+$> git clone https://github.com/texane/stlink stlink.git
\end{lstlisting}
\end{small}
\paragraph{}
-The GDB server is called st-util and is built using:\\
+Everything can be built from the top directory:\\
\begin{small}
\begin{lstlisting}[frame=tb]
-$> cd stlink.git; make ;
+$> cd stlink.git
+$> make CONFIG_USE_LIBSG=0
\end{lstlisting}
\end{small}
+It includes:
+\begin{itemize}
+\item a communication library (stlink.git/libstlink.a),
+\item a GDB server (stlink.git/gdbserver/st-util),
+\item a flash manipulation tool (stlink.git/flash/flash).
+\end{itemize}
\newpage
-
-\section{Building and running a program}
+\section{Building and running a program in SRAM}
+\paragraph{}
A simple LED blinking example is provided in the example directory. It is built using:\\
\begin{small}
\begin{lstlisting}[frame=tb]
-cd stlink.git/example ;
-PATH=$TOOLCHAIN_PATH/bin:$PATH make ;
+# update the make option accordingly to your architecture
+cd stlink.git/example/blink ;
+PATH=$TOOLCHAIN_PATH/bin:$PATH make CONFIG_STM32L_DISCOVERY=1;
\end{lstlisting}
\end{small}
\paragraph{}
-A GDB server must be start to interact with the STM32.
-Depending on the discovery kit you are using, you must
-run one of the 2 commands:\\
+A GDB server must be start to interact with the STM32. Depending on the discovery kit you
+are using, you must run one of the 2 commands:\\
\begin{small}
\begin{lstlisting}[frame=tb]
# STM32VL discovery kit
$> sudo ./st-util /dev/sg2
# STM32L discovery kit
-$> sudo ./st-util
+# 2 dummy command line arguments needed, will be fixed soon
+$> sudo ./st-util fu bar
\end{lstlisting}
\end{small}
From GDB, connect to the server using:\\
\begin{small}
\begin{lstlisting}[frame=tb]
-$> target extended-remote localhost:4242
+$> target extended localhost:4242
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+By default, the program was linked such that the base address is 0x20000000. From the architecture
+memory map, GDB knows this address belongs to SRAM. To load the program in SRAM, simply use:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+$> load blink.elf
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+GDB automatically set the PC register to the correct value, 0x20000000 in this case. Then, you
+can run the program using:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+$> continue
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+The board BLUE and GREEN leds should be blinking (those leds are near the user and reset buttons).
+
+
+\newpage
+\section{Building and flashing a program}
+\paragraph{}
+FLASH memory reading and writing is done by a separate tool, as shown below:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+# change to the flash tool directory
+$> cd stlink.git/flash ;
+
+# stlinkv1 command to read 4096 from flash into out.bin
+$> ./flash read /dev/sg2 out.bin 0x8000000 4096
+
+# stlinkv2 command
+$> ./flash read out.bin 0x8000000 4096
+
+# stlinkv1 command to write the file in.bin into flash
+$> ./flash write /dev/sg2 in.bin 0x8000000
+
+# stlinkv2 command
+$> ./flash write in.bin 0x8000000
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+A LED blinking example is provided:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+# build the example, resulting in blink.bin
+$> cd stlink.git/example/blink_flash
+$> PATH=$TOOLCHAIN_PATH:$PATH make CONFIG_STM32L_DISCOVERY=1
+
+# write blink.bin into FLASH
+$> sudo ./flash write blink.bin 0x08000000
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+Upon reset, the board LEDs should be blinking.
+
+\newpage
+\section{Building and installing the CHIBIOS kernel}
+\paragraph{}
+CHIBIOS is an open source RTOS. More information can be found on the project website:
+\begin{center}
+http://www.chibios.org/dokuwiki/doku.php
+\end{center}
+
+\paragraph{}
+It supports several boards, including the STM32L DISCOVERY kit:
+\begin{center}
+http://www.chibios.org/dokuwiki/doku.php?id=chibios:articles:stm32l\_discovery
+\end{center}
+
+\paragraph{}
+The installation procedure is detailed below:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+# checkout and build CHIBIOS for STM32L DISCOVERY kits
+svn checkout https://chibios.svn.sourceforge.net/svnroot/chibios/trunk
+cd chibios/trunk/demos/ARMCM3-STM32L152-DISCOVERY
+PATH=$TOOLCHAIN_PATH:$PATH make
+
+# flash the image into STM32L
+sudo ./flash write build/ch.bin 0x08000000
+\end{lstlisting}
+\end{small}
+
+\newpage
+\section{Notes}
+
+\subsection{Disassembling THUMB code in GDB}
+\paragraph{}
+By default, the disassemble command in GDB operates in ARM mode. The programs running on CORTEX-M3
+are compiled in THUMB mode. To correctly disassemble them under GDB, uses an odd address. For instance,
+if you want to disassemble the code at 0x20000000, use:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+$> disassemble 0x20000001
+\end{lstlisting}
+\end{small}
+
+
+\subsection{libstm32l\_discovery}
+\paragraph{}
+The repository includes the STM32L discovery library source code from ST original firmware packages,
+available here:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+http://www.st.com/internet/evalboard/product/250990.jsp#FIRMWARE
+\end{lstlisting}
+\end{small}
+
+\paragraph{}
+It is built using:\\
+\begin{small}
+\begin{lstlisting}[frame=tb]
+$> cd stlink.git/example/libstm32l_discovery/build
+$> make
\end{lstlisting}
\end{small}
\paragraph{}
-To load the program, use:\\
+An example using the library can be built using:\\
\begin{small}
\begin{lstlisting}[frame=tb]
-$> load program.elf
+$> cd stlink.git/example/lcd
+$> make
\end{lstlisting}
\end{small}
+\subsection{STM32VL support}
\paragraph{}
-Then, you can run the program using:\\
+It seems support for STM32VL is quite broken. If it does not work, try build STLINK using libsg:
\begin{small}
\begin{lstlisting}[frame=tb]
-$> run
+$> cd stlink.git
+$> make CONFIG_USE_LIBSG=1
\end{lstlisting}
\end{small}
\section{References}
\begin{itemize}
\item http://www.st.com/internet/mcu/product/248823.jsp\\
- all the documentation related to STM32L discovery kit
+ documentation related to the STM32L mcu
+\item http://www.st.com/internet/evalboard/product/250990.jsp\\
+ documentation related to the STM32L discovery kit
\end{itemize}
\end{document}
projects / fw / stlink / blobdiff