proc init_board @{@} @{
reset_config trst_and_srst trst_pulls_srst
+ $_TARGETNAME configure -event reset-start @{
+ adapter_khz 100
+ @}
+
$_TARGETNAME configure -event reset-init @{
- adapter_khz 1
enable_fast_clock
adapter_khz 10000
@}
@end deffn
+@deffn {Interface Driver} {ft232r}
+This driver is implementing synchronous bitbang mode of an FTDI FT232R
+USB UART bridge IC.
+
+List of connections (pin numbers for SSOP):
+@itemize @minus
+@item RXD(5) - TDI
+@item TXD(1) - TCK
+@item RTS(3) - TDO
+@item CTS(11) - TMS
+@item DTR(2) - TRST
+@item DCD(10) - SRST
+@end itemize
+
+These interfaces have several commands, used to configure the driver
+before initializing the JTAG scan chain:
+
+@deffn {Config Command} {ft232r_vid_pid} @var{vid} @var{pid}
+The vendor ID and product ID of the adapter. If not specified, default
+0x0403:0x6001 is used.
+@end deffn
+
+@deffn {Config Command} {ft232r_serial_desc} @var{serial}
+Specifies the @var{serial} of the adapter to use, in case the
+vendor provides unique IDs and more than one adapter is connected to
+the host. If not specified, serial numbers are not considered.
+@end deffn
+
+@end deffn
+
@deffn {Interface Driver} {remote_bitbang}
Drive JTAG from a remote process. This sets up a UNIX or TCP socket connection
with a remote process and sends ASCII encoded bitbang requests to that process
Specifies the adapter layout to use.
@end deffn
-@deffn {Config Command} {hla_vid_pid} vid pid
-The vendor ID and product ID of the device.
+@deffn {Config Command} {hla_vid_pid} [vid pid]+
+Pairs of vendor IDs and product IDs of the device.
@end deffn
@deffn {Command} {hla_command} command
resources; then a @file{board.cfg} with off-chip resources, clocking,
and so forth.
+@anchor{dapdeclaration}
+@section DAP declaration (ARMv7 and ARMv8 targets)
+@cindex DAP declaration
+
+Since OpenOCD version 0.11.0, the Debug Access Port (DAP) is
+no longer implicitly created together with the target. It must be
+explicitly declared using the @command{dap create} command. For all
+ARMv7 and ARMv8 targets, the option "@option{-dap} @var{dap_name}" has to be used
+instead of "@option{-chain-position} @var{dotted.name}" when the target is created.
+
+The @command{dap} command group supports the following sub-commands:
+
+@deffn Command {dap create} dap_name @option{-chain-position} dotted.name
+Declare a DAP instance named @var{dap_name} linked to the JTAG tap
+@var{dotted.name}. This also creates a new command (@command{dap_name})
+which is used for various purposes including additional configuration.
+There can only be one DAP for each JTAG tap in the system.
+@end deffn
+
+@deffn Command {dap names}
+This command returns a list of all registered DAP objects. It it useful mainly
+for TCL scripting.
+@end deffn
+
+@deffn Command {dap info} [num]
+Displays the ROM table for MEM-AP @var{num},
+defaulting to the currently selected AP of the currently selected target.
+@end deffn
+
+@deffn Command {dap init}
+Initialize all registered DAPs. This command is used internally
+during initialization. It can be issued at any time after the
+initialization, too.
+@end deffn
+
+The following commands exist as subcommands of DAP instances:
+
+@deffn Command {$dap_name info} [num]
+Displays the ROM table for MEM-AP @var{num},
+defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {$dap_name apid} [num]
+Displays ID register from AP @var{num}, defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {$dap_name apreg} ap_num reg [value]
+Displays content of a register @var{reg} from AP @var{ap_num}
+or set a new value @var{value}.
+@var{reg} is byte address of a word register, 0, 4, 8 ... 0xfc.
+@end deffn
+
+@deffn Command {$dap_name apsel} [num]
+Select AP @var{num}, defaulting to 0.
+@end deffn
+
+@deffn Command {$dap_name baseaddr} [num]
+Displays debug base address from MEM-AP @var{num},
+defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {$dap_name memaccess} [value]
+Displays the number of extra tck cycles in the JTAG idle to use for MEM-AP
+memory bus access [0-255], giving additional time to respond to reads.
+If @var{value} is defined, first assigns that.
+@end deffn
+
+@deffn Command {$dap_name apcsw} [0 / 1]
+fix CSW_SPROT from register AP_REG_CSW on selected dap.
+Defaulting to 0.
+@end deffn
+
+@deffn Command {$dap_name ti_be_32_quirks} [@option{enable}]
+Set/get quirks mode for TI TMS450/TMS570 processors
+Disabled by default
+@end deffn
+
+
@node CPU Configuration
@chapter CPU Configuration
@cindex GDB target
The key steps you use might look something like this
@example
-target create MyTarget cortex_m -chain-position mychip.cpu
-$MyTarget configure -work-area-phys 0x08000 -work-area-size 8096
-$MyTarget configure -event reset-deassert-pre @{ jtag_rclk 5 @}
-$MyTarget configure -event reset-init @{ myboard_reinit @}
+dap create mychip.dap -chain-position mychip.cpu
+target create MyTarget cortex_m -dap mychip.dap
+MyTarget configure -work-area-phys 0x08000 -work-area-size 8096
+MyTarget configure -event reset-deassert-pre @{ jtag_rclk 5 @}
+MyTarget configure -event reset-init @{ myboard_reinit @}
@end example
You should specify a working area if you can; typically it uses some
@command{$target_name configure} are permitted.
If the target is big-endian, set it here with @code{-endian big}.
-You @emph{must} set the @code{-chain-position @var{dotted.name}} here.
+You @emph{must} set the @code{-chain-position @var{dotted.name}} or
+@code{-dap @var{dap_name}} here.
@end itemize
@end deffn
@item @code{-chain-position} @var{dotted.name} -- names the TAP
used to access this target.
+@item @code{-dap} @var{dap_name} -- names the DAP used to access
+this target. @xref{dapdeclaration,,DAP declaration}, on how to
+create and manage DAP instances.
+
@item @code{-endian} (@option{big}|@option{little}) -- specifies
whether the CPU uses big or little endian conventions
two different handlers, but calling it twice with the
same event name assigns only one handler.
+Current target is temporarily overridden to the event issuing target
+before handler code starts and switched back after handler is done.
+
@item @code{-work-area-backup} (@option{0}|@option{1}) -- says
whether the work area gets backed up; by default,
@emph{it is not backed up.}
Use this option with systems where multiple, independent cores are connected
to separate access ports of the same DAP.
-@item @code{-ctibase} @var{address} -- set base address of Cross-Trigger interface (CTI) connected
-to the target. Currently, only the @code{aarch64} target makes use of this option, where it is
-a mandatory configuration for the target run control.
+@item @code{-cti} @var{cti_name} -- set Cross-Trigger Interface (CTI) connected
+to the target. Currently, only the @code{aarch64} target makes use of this option,
+where it is a mandatory configuration for the target run control.
+@xref{armcrosstrigger,,ARM Cross-Trigger Interface},
+for instruction on how to declare and control a CTI instance.
@end itemize
@end deffn
and invokes a small procedure while the other inlines it.
@example
-proc my_attach_proc @{ @} @{
- echo "Reset..."
- reset halt
+proc my_init_proc @{ @} @{
+ echo "Disabling watchdog..."
+ mww 0xfffffd44 0x00008000
@}
-mychip.cpu configure -event gdb-attach my_attach_proc
-mychip.cpu configure -event gdb-attach @{
- echo "Reset..."
- # To make flash probe and gdb load to flash work
- # we need a reset init.
- reset init
+mychip.cpu configure -event reset-init my_init_proc
+mychip.cpu configure -event reset-init @{
+ echo "Disabling watchdog..."
+ mww 0xfffffd44 0x00008000
@}
@end example
@item @b{debug-halted}
@* The target has halted for debug reasons (i.e.: breakpoint)
@item @b{debug-resumed}
-@* The target has resumed (i.e.: gdb said run)
+@* The target has resumed (i.e.: GDB said run)
@item @b{early-halted}
@* Occurs early in the halt process
@item @b{examine-start}
@item @b{examine-end}
@* After target examine is called with no errors.
@item @b{gdb-attach}
-@* When GDB connects. This is before any communication with the target, so this
-can be used to set up the target so it is possible to probe flash. Probing flash
-is necessary during gdb connect if gdb load is to write the image to flash. Another
-use of the flash memory map is for GDB to automatically hardware/software breakpoints
-depending on whether the breakpoint is in RAM or read only memory.
+@* When GDB connects. Issued before any GDB communication with the target
+starts. GDB expects the target is halted during attachment.
+@xref{gdbmeminspect,,GDB as a non-intrusive memory inspector}, how to
+connect GDB to running target.
+The event can be also used to set up the target so it is possible to probe flash.
+Probing flash is necessary during GDB connect if you want to use
+@pxref{programmingusinggdb,,programming using GDB}.
+Another use of the flash memory map is for GDB to automatically choose
+hardware or software breakpoints depending on whether the breakpoint
+is in RAM or read only memory.
+Default is @code{halt}
@item @b{gdb-detach}
@* When GDB disconnects
@item @b{gdb-end}
@item @b{gdb-flash-write-end}
@* After GDB writes to the flash (default is @code{reset halt})
@item @b{gdb-start}
-@* Before the target steps, gdb is trying to start/resume the target
+@* Before the target steps, GDB is trying to start/resume the target
@item @b{halted}
@* The target has halted
@item @b{reset-assert-pre}
@* Issued as part of @command{reset} processing
-after @command{reset_init} was triggered
-but before either SRST alone is re-asserted on the scan chain,
+after @command{reset-start} was triggered
+but before either SRST alone is asserted on the scan chain,
or @code{reset-assert} is triggered.
@item @b{reset-assert}
@* Issued as part of @command{reset} processing
released on the scan chain.
@item @b{reset-end}
@* Issued as the final step in @command{reset} processing.
-@ignore
-@item @b{reset-halt-post}
-@* Currently not used
-@item @b{reset-halt-pre}
-@* Currently not used
-@end ignore
@item @b{reset-init}
@* Used by @b{reset init} command for board-specific initialization.
This event fires after @emph{reset-deassert-post}.
(You may be able to switch to a fast JTAG clock rate here, after
the target clocks are fully set up.)
@item @b{reset-start}
-@* Issued as part of @command{reset} processing
-before @command{reset_init} is called.
+@* Issued as the first step in @command{reset} processing
+before @command{reset-assert-pre} is called.
This is the most robust place to use @command{jtag_rclk}
or @command{adapter_khz} to switch to a low JTAG clock rate,
when reset disables PLLs needed to use a fast clock.
-@ignore
-@item @b{reset-wait-pos}
-@* Currently not used
-@item @b{reset-wait-pre}
-@* Currently not used
-@end ignore
@item @b{resume-start}
@* Before any target is resumed
@item @b{resume-end}
@item @var{ir} ... is loaded into the JTAG IR to map the flash as the JTAG DR.
For the bitstreams generated from @file{xilinx_bscan_spi.py} this is the
@var{USER1} instruction.
-@item @var{dr_length} ... is the length of the DR register. This will be 1 for
-@file{xilinx_bscan_spi.py} bitstreams and most other cases.
@end itemize
@example
target create $_TARGETNAME testee -chain-position $_CHIPNAME.fpga
set _XILINX_USER1 0x02
-set _DR_LENGTH 1
flash bank $_FLASHNAME spi 0x0 0 0 0 \
- $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
+ $_TARGETNAME $_XILINX_USER1
+@end example
+@end deffn
+
+@deffn {Flash Driver} xcf
+@cindex Xilinx Platform flash driver
+@cindex xcf
+Xilinx FPGAs can be configured from specialized flash ICs named Platform Flash.
+It is (almost) regular NOR flash with erase sectors, program pages, etc. The
+only difference is special registers controlling its FPGA specific behavior.
+They must be properly configured for successful FPGA loading using
+additional @var{xcf} driver command:
+
+@deffn Command {xcf ccb} <bank_id>
+command accepts additional parameters:
+@itemize
+@item @var{external|internal} ... selects clock source.
+@item @var{serial|parallel} ... selects serial or parallel data bus mode.
+@item @var{slave|master} ... selects slave of master mode for flash device.
+@item @var{40|20} ... selects clock frequency in MHz for internal clock
+in master mode.
+@end itemize
+@example
+xcf ccb 0 external parallel slave 40
+@end example
+All of them must be specified even if clock frequency is pointless
+in slave mode. If only bank id specified than command prints current
+CCB register value. Note: there is no need to write this register
+every time you erase/program data sectors because it stores in
+dedicated sector.
+@end deffn
+
+@deffn Command {xcf configure} <bank_id>
+Initiates FPGA loading procedure. Useful if your board has no "configure"
+button.
+@example
+xcf configure 0
@end example
@end deffn
+Additional driver notes:
+@itemize
+@item Only single revision supported.
+@item Driver automatically detects need of bit reverse, but
+only "bin" (raw binary, do not confuse it with "bit") and "mcs"
+(Intel hex) file types supported.
+@item For additional info check xapp972.pdf and ug380.pdf.
+@end itemize
+@end deffn
+
@deffn {Flash Driver} lpcspifi
@cindex NXP SPI Flash Interface
@cindex SPIFI
Command is used internally in event event reset-deassert-post.
@end deffn
+@deffn Command {at91samd nvmuserrow}
+Writes or reads the entire 64 bit wide NVM user row register which is located at
+0x804000. This register includes various fuses lock-bits and factory calibration
+data. Reading the register is done by invoking this command without any
+arguments. Writing is possible by giving 1 or 2 hex values. The first argument
+is the register value to be written and the second one is an optional changemask.
+Every bit which value in changemask is 0 will stay unchanged. The lock- and
+reserved-bits are masked out and cannot be changed.
+
+@example
+# Read user row
+>at91samd nvmuserrow
+NVMUSERROW: 0xFFFFFC5DD8E0C788
+# Write 0xFFFFFC5DD8E0C788 to user row
+>at91samd nvmuserrow 0xFFFFFC5DD8E0C788
+# Write 0x12300 to user row but leave other bits and low byte unchanged
+>at91samd nvmuserrow 0x12345 0xFFF00
+@end example
+@end deffn
+
@end deffn
@anchor{at91sam3}
@comment - defines mass_erase ... pointless given flash_erase_address
@end deffn
+@deffn {Flash Driver} bluenrg-x
+STMicroelectronics BlueNRG-1 and BlueNRG-2 Bluetooth low energy wireless system-on-chip. They include ARM Cortex-M0 core and internal flash memory.
+The driver automatically recognizes these chips using
+the chip identification registers, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME bluenrg-x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that when users ask to erase all the sectors of the flash, a mass erase command is used which is faster than erasing
+each single sector one by one.
+
+@example
+flash erase_sector 0 0 79 # It will perform a mass erase on BlueNRG-1
+@end example
+
+@example
+flash erase_sector 0 0 127 # It will perform a mass erase on BlueNRG-2
+@end example
+
+Triggering a mass erase is also useful when users want to disable readout protection.
+
+@end deffn
+
@deffn {Flash Driver} efm32
All members of the EFM32 microcontroller family from Energy Micro include
internal flash and use ARM Cortex-M3 cores. The driver automatically recognizes
internal flash and use ARM Cortex-M0+ or M4 cores. The driver automatically
recognizes flash size and a number of flash banks (1-4) using the chip
identification register, and autoconfigures itself.
-Use kinetis_ke driver for KE0x devices.
+Use kinetis_ke driver for KE0x and KEAx devices.
The @var{kinetis} driver defines option:
@itemize
@deffn {Flash Driver} kinetis_ke
@cindex kinetis_ke
-KE0x members of the Kinetis microcontroller family from Freescale include
+KE0x and KEAx members of the Kinetis microcontroller family from NXP include
internal flash and use ARM Cortex-M0+. The driver automatically recognizes
the KE0x sub-family using the chip identification register, and
autoconfigures itself.
@end deffn
@end deffn
+@deffn {Flash Driver} psoc6
+Supports PSoC6 (CY8C6xxx) family of Cypress microcontrollers.
+PSoC6 is a dual-core device with CM0+ and CM4 cores. Both cores share
+the same Flash/RAM/MMIO address space.
+
+Flash in PSoC6 is split into three regions:
+@itemize @bullet
+@item Main Flash - this is the main storage for user application.
+Total size varies among devices, sector size: 256 kBytes, row size:
+512 bytes. Supports erase operation on individual rows.
+@item Work Flash - intended to be used as storage for user data
+(e.g. EEPROM emulation). Total size: 32 KBytes, sector size: 32 KBytes,
+row size: 512 bytes.
+@item Supervisory Flash - special region which contains device-specific
+service data. This region does not support erase operation. Only few rows can
+be programmed by the user, most of the rows are read only. Programming
+operation will erase row automatically.
+@end itemize
+
+All three flash regions are supported by the driver. Flash geometry is detected
+automatically by parsing data in SPCIF_GEOMETRY register.
+
+PSoC6 is equipped with NOR Flash so erased Flash reads as 0x00.
+
+@example
+flash bank main_flash_cm0 psoc6 0x10000000 0 0 0 $@{TARGET@}.cm0
+flash bank work_flash_cm0 psoc6 0x14000000 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_user_cm0 psoc6 0x16000800 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_nar_cm0 psoc6 0x16001A00 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_key_cm0 psoc6 0x16005A00 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_toc2_cm0 psoc6 0x16007C00 0 0 0 $@{TARGET@}.cm0
+
+flash bank main_flash_cm4 psoc6 0x10000000 0 0 0 $@{TARGET@}.cm4
+flash bank work_flash_cm4 psoc6 0x14000000 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_user_cm4 psoc6 0x16000800 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_nar_cm4 psoc6 0x16001A00 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_key_cm4 psoc6 0x16005A00 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_toc2_cm4 psoc6 0x16007C00 0 0 0 $@{TARGET@}.cm4
+@end example
+
+psoc6-specific commands
+@deffn Command {psoc6 reset_halt}
+Command can be used to simulate broken Vector Catch from gdbinit or tcl scripts.
+When invoked for CM0+ target, it will set break point at application entry point
+and issue SYSRESETREQ. This will reset both cores and all peripherals. CM0+ will
+reset CM4 during boot anyway so this is safe. On CM4 target, VECTRESET is used
+instead of SYSRESETREQ to avoid unwanted reset of CM0+;
+@end deffn
+
+@deffn Command {psoc6 mass_erase} num
+Erases the contents given flash bank. The @var{num} parameter is a value shown
+by @command{flash banks}.
+Note: only Main and Work flash regions support Erase operation.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} sim3x
All members of the SiM3 microcontroller family from Silicon Laboratories
include internal flash and use ARM Cortex-M3 cores. It supports both JTAG
families from Texas Instruments include internal flash. The driver
automatically recognizes a number of these chips using the chip
identification register, and autoconfigures itself.
-@footnote{Currently there is a @command{stellaris mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
@example
flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
@end example
-Some stm32f1x-specific commands
-@footnote{Currently there is a @command{stm32f1x mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
-are defined:
+Some stm32f1x-specific commands are defined:
@deffn Command {stm32f1x lock} num
Locks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {stm32f1x mass_erase} num
+Mass erases the entire stm32f1x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32f1x options_read} num
Read and display the stm32 option bytes written by
the @command{stm32f1x options_write} command.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
+@example
+flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
+@end example
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {stm32f2x mass_erase} num
+Mass erases the entire stm32f2x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32f2x options_read} num
Reads and displays user options and (where implemented) boot_addr0, boot_addr1, optcr2.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
+@deffn {Flash Driver} stm32h7x
+All members of the STM32H7 microcontroller families from ST Microelectronics
+include internal flash and use ARM Cortex-M7 core.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32h7x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32h7x 0 0x20000 0 0 $_TARGETNAME
+@end example
+
+Some stm32h7x-specific commands are defined:
+
+@deffn Command {stm32h7x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32h7x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32h7x mass_erase} num
+Mass erases the entire stm32h7x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} stm32lx
All members of the STM32L microcontroller families from ST Microelectronics
include internal flash and use ARM Cortex-M3 and Cortex-M0+ cores.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
+@example
+flash bank $_FLASHNAME stm32lx 0 0 0 0 $_TARGETNAME
+@end example
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver. If you use 0 as the bank base address, it tells the
Some stm32lx-specific commands are defined:
+@deffn Command {stm32lx lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32lx unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32lx mass_erase} num
Mass erases the entire stm32lx device (all flash banks and EEPROM
data). This is the only way to unlock a protected flash (unless RDP
@end deffn
@end deffn
+@deffn {Flash Driver} stm32l4x
+All members of the STM32L4 microcontroller families from ST Microelectronics
+include internal flash and use ARM Cortex-M4 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32l4x 0x08000000 0x40000 0 0 $_TARGETNAME
+@end example
+
+Some stm32l4x-specific commands are defined:
+
+@deffn Command {stm32l4x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32l4x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32l4x mass_erase} num
+Mass erases the entire stm32l4x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} str7x
All members of the STR7 microcontroller family from ST Microelectronics
include internal flash and use ARM7TDMI cores.
Add @var{directory} to the file/script search path.
@end deffn
-@deffn Command bindto [name]
-Specify address by name on which to listen for incoming TCP/IP connections.
-By default, OpenOCD will listen on all available interfaces.
+@deffn Command bindto [@var{name}]
+Specify hostname or IPv4 address on which to listen for incoming
+TCP/IP connections. By default, OpenOCD will listen on the loopback
+interface only. If your network environment is safe, @code{bindto
+0.0.0.0} can be used to cover all available interfaces.
@end deffn
@anchor{targetstatehandling}
@end deffn
@end deffn
+@anchor{armcrosstrigger}
+@section ARM Cross-Trigger Interface
+@cindex CTI
+
+The ARM Cross-Trigger Interface (CTI) is a generic CoreSight component
+that connects event sources like tracing components or CPU cores with each
+other through a common trigger matrix (CTM). For ARMv8 architecture, a
+CTI is mandatory for core run control and each core has an individual
+CTI instance attached to it. OpenOCD has limited support for CTI using
+the @emph{cti} group of commands.
+
+@deffn Command {cti create} cti_name @option{-dap} dap_name @option{-ap-num} apn @option{-ctibase} base_address
+Creates a CTI instance @var{cti_name} on the DAP instance @var{dap_name} on MEM-AP
+@var{apn}. The @var{base_address} must match the base address of the CTI
+on the respective MEM-AP. All arguments are mandatory. This creates a
+new command @command{$cti_name} which is used for various purposes
+including additional configuration.
+@end deffn
+
+@deffn Command {$cti_name enable} @option{on|off}
+Enable (@option{on}) or disable (@option{off}) the CTI.
+@end deffn
+
+@deffn Command {$cti_name dump}
+Displays a register dump of the CTI.
+@end deffn
+
+@deffn Command {$cti_name write } @var{reg_name} @var{value}
+Write @var{value} to the CTI register with the symbolic name @var{reg_name}.
+@end deffn
+
+@deffn Command {$cti_name read} @var{reg_name}
+Print the value read from the CTI register with the symbolic name @var{reg_name}.
+@end deffn
+
+@deffn Command {$cti_name testmode} @option{on|off}
+Enable (@option{on}) or disable (@option{off}) the integration test mode
+of the CTI.
+@end deffn
+
+@deffn Command {cti names}
+Prints a list of names of all CTI objects created. This command is mainly
+useful in TCL scripting.
+@end deffn
@section Generic ARM
@cindex ARM
@cindex ARMv7
@cindex ARMv8
-@subsection ARMv7 and ARMv8 Debug Access Port (DAP) specific commands
-@cindex Debug Access Port
-@cindex DAP
-These commands are specific to ARM architecture v7 and v8 Debug Access Port (DAP),
-included on Cortex-M and Cortex-A systems.
-They are available in addition to other core-specific commands that may be available.
-
-@deffn Command {dap apid} [num]
-Displays ID register from AP @var{num},
-defaulting to the currently selected AP.
-@end deffn
-
-@deffn Command {dap apreg} ap_num reg [value]
-Displays content of a register @var{reg} from AP @var{ap_num}
-or set a new value @var{value}.
-@var{reg} is byte address of a word register, 0, 4, 8 ... 0xfc.
-@end deffn
-
-@deffn Command {dap apsel} [num]
-Select AP @var{num}, defaulting to 0.
-@end deffn
-
-@deffn Command {dap baseaddr} [num]
-Displays debug base address from MEM-AP @var{num},
-defaulting to the currently selected AP.
-@end deffn
-
-@deffn Command {dap info} [num]
-Displays the ROM table for MEM-AP @var{num},
-defaulting to the currently selected AP.
-@end deffn
-
-@deffn Command {dap memaccess} [value]
-Displays the number of extra tck cycles in the JTAG idle to use for MEM-AP
-memory bus access [0-255], giving additional time to respond to reads.
-If @var{value} is defined, first assigns that.
-@end deffn
-
-@deffn Command {dap apcsw} [0 / 1]
-fix CSW_SPROT from register AP_REG_CSW on selected dap.
-Defaulting to 0.
-@end deffn
-
-@deffn Command {dap ti_be_32_quirks} [@option{enable}]
-Set/get quirks mode for TI TMS450/TMS570 processors
-Disabled by default
-@end deffn
-
-
@subsection ARMv7-A specific commands
@cindex Cortex-A
group. With SMP handling disabled, all targets need to be treated individually.
@end deffn
+@deffn Command {aarch64 maskisr} [@option{on}|@option{off}]
+Selects whether interrupts will be processed when single stepping. The default configuration is
+@option{on}.
+@end deffn
+
@section Intel Architecture
Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32
In a debug session using JTAG for its transport protocol,
OpenOCD supports running such test files.
-@deffn Command {svf} filename [@option{quiet}]
+@deffn Command {svf} @file{filename} [@option{-tap @var{tapname}}] [@option{[-]quiet}] @
+ [@option{[-]nil}] [@option{[-]progress}] [@option{[-]ignore_error}]
This issues a JTAG reset (Test-Logic-Reset) and then
runs the SVF script from @file{filename}.
-Unless the @option{quiet} option is specified,
-each command is logged before it is executed.
+
+Arguments can be specified in any order; the optional dash doesn't
+affect their semantics.
+
+Command options:
+@itemize @minus
+@item @option{-tap @var{tapname}} ignore IR and DR headers and footers
+specified by the SVF file with HIR, TIR, HDR and TDR commands;
+instead, calculate them automatically according to the current JTAG
+chain configuration, targetting @var{tapname};
+@item @option{[-]quiet} do not log every command before execution;
+@item @option{[-]nil} ``dry run'', i.e., do not perform any operations
+on the real interface;
+@item @option{[-]progress} enable progress indication;
+@item @option{[-]ignore_error} continue execution despite TDO check
+errors.
+@end itemize
@end deffn
@section XSVF: Xilinx Serial Vector Format
only work for code running from flash memory. Most other ARM systems
do not have such restrictions.
-Another example of useful GDB configuration came from a user who
-found that single stepping his Cortex-M3 didn't work well with IRQs
-and an RTOS until he told GDB to disable the IRQs while stepping:
-
-@example
-define hook-step
-mon cortex_m maskisr on
-end
-define hookpost-step
-mon cortex_m maskisr off
-end
-@end example
-
Rather than typing such commands interactively, you may prefer to
save them in a file and have GDB execute them as it starts, perhaps
using a @file{.gdbinit} in your project directory or starting GDB
areas to be programmed lie within the target flash area the vFlash packets
will be used.
-If the target needs configuring before GDB programming, an event
-script can be executed:
+If the target needs configuring before GDB programming, set target
+event gdb-flash-erase-start:
@example
-$_TARGETNAME configure -event EVENTNAME BODY
+$_TARGETNAME configure -event gdb-flash-erase-start BODY
@end example
+@xref{targetevents,,Target Events}, for other GDB programming related events.
To verify any flash programming the GDB command @option{compare-sections}
can be used.
+
+@section Using GDB as a non-intrusive memory inspector
+@cindex Using GDB as a non-intrusive memory inspector
+@anchor{gdbmeminspect}
+
+If your project controls more than a blinking LED, let's say a heavy industrial
+robot or an experimental nuclear reactor, stopping the controlling process
+just because you want to attach GDB is not a good option.
+
+OpenOCD does not support GDB non-stop mode (might be implemented in the future).
+Though there is a possible setup where the target does not get stopped
+and GDB treats it as it were running.
+If the target supports background access to memory while it is running,
+you can use GDB in this mode to inspect memory (mainly global variables)
+without any intrusion of the target process.
+
+Remove default setting of gdb-attach event. @xref{targetevents,,Target Events}.
+Place following command after target configuration:
+@example
+$_TARGETNAME configure -event gdb-attach @{@}
+@end example
+
+If any of installed flash banks does not support probe on running target,
+switch off gdb_memory_map:
+@example
+gdb_memory_map disable
+@end example
+
+Ensure GDB is configured without interrupt-on-connect.
+Some GDB versions set it by default, some does not.
+@example
+set remote interrupt-on-connect off
+@end example
+
+If you switched gdb_memory_map off, you may want to setup GDB memory map
+manually or issue @command{set mem inaccessible-by-default off}
+
+Now you can issue GDB command @command{target remote ...} and inspect memory
+of a running target. Do not use GDB commands @command{continue},
+@command{step} or @command{next} as they synchronize GDB with your target
+and GDB would require stopping the target to get the prompt back.
+
+Do not use this mode under an IDE like Eclipse as it caches values of
+previously shown varibles.
+
@anchor{usingopenocdsmpwithgdb}
@section Using OpenOCD SMP with GDB
@cindex SMP
projects / fw / openocd / blobdiff