This command is only available if your libusb1 is at least version 1.0.16.
@end deffn
+@deffn {Config Command} {adapter serial} serial_string
+Specifies the @var{serial_string} of the adapter to use.
+If this command is not specified, serial strings are not checked.
+Only the following adapter drivers use the serial string from this command:
+cmsis_dap, ft232r, ftdi, kitprog.
+The following adapters have their own command to specify the serial string:
+hla, jlink, presto, st-link, vsllink, xds110.
+@end deffn
+
@section Interface Drivers
Each of the interface drivers listed here must be explicitly
@end example
@end deffn
-@deffn {Config Command} {cmsis_dap_serial} [serial]
-Specifies the @var{serial} of the CMSIS-DAP device to use.
-If not specified, serial numbers are not considered.
-@end deffn
-
@deffn {Config Command} {cmsis_dap_backend} [@option{auto}|@option{usb_bulk}|@option{hid}]
Specifies how to communicate with the adapter:
during device selection.
@end deffn
-@deffn {Config Command} {ftdi serial} serial-number
-Specifies the @var{serial-number} of the adapter to use,
-in case the vendor provides unique IDs and more than one adapter
-is connected to the host.
-If not specified, serial numbers are not considered.
-(Note that USB serial numbers can be arbitrary Unicode strings,
-and are not restricted to containing only decimal digits.)
-@end deffn
-
@deffn {Config Command} {ftdi channel} channel
Selects the channel of the FTDI device to use for MPSSE operations. Most
adapters use the default, channel 0, but there are exceptions.
0x0403:0x6001 is used.
@end deffn
-@deffn {Config Command} {ft232r serial_desc} @var{serial}
-Specifies the @var{serial} of the adapter to use, in case the
-vendor provides unique IDs and more than one adapter is connected to
-the host. If not specified, serial numbers are not considered.
-@end deffn
-
@deffn {Config Command} {ft232r jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
Set four JTAG GPIO numbers at once.
If not specified, default 0 3 1 2 or TXD CTS RXD RTS is used.
@deffn {Command} {jlink config write}
Write the current configuration to the internal persistent storage.
@end deffn
-@deffn {Command} {jlink emucom write <channel> <data>}
+@deffn {Command} {jlink emucom write} <channel> <data>
Write data to an EMUCOM channel. The data needs to be encoded as hexadecimal
pairs.
> jlink emucom write 0x10 aa0b23
@end example
@end deffn
-@deffn {Command} {jlink emucom read <channel> <length>}
+@deffn {Command} {jlink emucom read} <channel> <length>
Read data from an EMUCOM channel. The read data is encoded as hexadecimal
pairs.
Please be aware that the acquisition sequence hard-resets the target.
@end deffn
-@deffn {Config Command} {kitprog_serial} serial
-Select a KitProg device by its @var{serial}. If left unspecified, the first
-device detected by OpenOCD will be used.
-@end deffn
-
@deffn {Command} {kitprog acquire_psoc}
Run a PSoC acquisition sequence immediately. Typically, this should not be used
outside of the target-specific configuration scripts since it hard-resets the
flash bank $_FLASHNAME stm32f2x 0x1FFF7800 0 0 0 $_TARGETNAME
@end example
-@deffn {Command} {stm32f2x otp } num (@option{enable}|@option{disable}|@option{show})
+@deffn {Command} {stm32f2x otp} num (@option{enable}|@option{disable}|@option{show})
Enables or disables OTP write commands for bank @var{num}.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
Saves programming keys in a register, to enable flash erase and write commands.
@end deffn
-@deffn {Command} {tms470 osc_mhz} clock_mhz
+@deffn {Command} {tms470 osc_megahertz} clock_mhz
Reports the clock speed, which is used to calculate timings.
@end deffn
Stop RTT.
@end deffn
-@deffn {Command} {rtt polling_interval [interval]}
+@deffn {Command} {rtt polling_interval} [interval]
Display the polling interval.
If @var{interval} is provided, set the polling interval.
The polling interval determines (in milliseconds) how often the up-channels are
Displays a register dump of the CTI.
@end deffn
-@deffn {Command} {$cti_name write } @var{reg_name} @var{value}
+@deffn {Command} {$cti_name write} @var{reg_name} @var{value}
Write @var{value} to the CTI register with the symbolic name @var{reg_name}.
@end deffn
display information about target caches
@end deffn
-@deffn {Command} {cortex_a dacrfixup [@option{on}|@option{off}]}
+@deffn {Command} {cortex_a dacrfixup} [@option{on}|@option{off}]
Work around issues with software breakpoints when the program text is
mapped read-only by the operating system. This option sets the CP15 DACR
to "all-manager" to bypass MMU permission checks on memory access.
@subsection ARMv7-R specific commands
@cindex Cortex-R
-@deffn {Command} {cortex_r dbginit}
+@deffn {Command} {cortex_r4 dbginit}
Initialize core debug
Enables debug by unlocking the Software Lock and clearing sticky powerdown indications
@end deffn
-@deffn {Command} {cortex_r maskisr} [@option{on}|@option{off}]
+@deffn {Command} {cortex_r4 maskisr} [@option{on}|@option{off}]
Selects whether interrupts will be processed when single stepping
@end deffn
addreg rtest 0x1234 org.gnu.gdb.or1k.group0 system
@end example
-
-@end deffn
-@deffn {Command} {readgroup} (@option{group})
-Display all registers in @emph{group}.
-
-@emph{group} can be "system",
- "dmmu", "immu", "dcache", "icache", "mac", "debug", "perf", "power", "pic",
- "timer" or any new group created with addreg command.
@end deffn
@section RISC-V Architecture
projects / fw / openocd / blobdiff