The OpenOCD web site provides the latest public news from the community:
-@uref{http://openocd.berlios.de/web/}
+@uref{http://openocd.sourceforge.net/}
@section Latest User's Guide:
available. A version for more recent code may be available.
Its HTML form is published irregularly at:
-@uref{http://openocd.berlios.de/doc/html/index.html}
+@uref{http://openocd.sourceforge.net/doc/html/index.html}
PDF form is likewise published at:
-@uref{http://openocd.berlios.de/doc/pdf/openocd.pdf}
+@uref{http://openocd.sourceforge.net/doc/pdf/openocd.pdf}
@section OpenOCD User's Forum
technical information about the software internals, development
processes, and similar documentation:
-@uref{http://openocd.berlios.de/doc/doxygen/index.html}
+@uref{http://openocd.sourceforge.net/doc/doxygen/html/index.html}
This document is a work-in-progress, but contributions would be welcome
to fill in the gaps. All of the source files are provided in-tree,
The OpenOCD Developer Mailing List provides the primary means of
communication between developers:
-@uref{https://lists.berlios.de/mailman/listinfo/openocd-development}
+@uref{https://lists.sourceforge.net/mailman/listinfo/openocd-devel}
Discuss and submit patches to this list.
The @file{PATCHES.txt} file contains basic information about how
@item @b{Jim vs. Tcl}
@* Jim-Tcl is a stripped down version of the well known Tcl language,
which can be found here: @url{http://www.tcl.tk}. Jim-Tcl has far
-fewer features. Jim-Tcl is a single .C file and a single .H file and
+fewer features. Jim-Tcl is several dozens of .C files and .H files and
implements the basic Tcl command set. In contrast: Tcl 8.6 is a
4.2 MB .zip file containing 1540 files.
@example
Open On-Chip Debugger 0.4.0 (2010-01-14-15:06)
For bug reports, read
- http://openocd.berlios.de/doc/doxygen/bugs.html
+ http://openocd.sourceforge.net/doc/doxygen/bugs.html
Info : JTAG tap: lm3s.cpu tap/device found: 0x3ba00477
(mfg: 0x23b, part: 0xba00, ver: 0x3)
@end example
You can redirect all output from the daemon to a file using the
@option{-l <logfile>} switch.
-For details on the @option{-p} option. @xref{Connecting to GDB}.
-
Note! OpenOCD will launch the GDB & telnet server even if it can not
establish a connection with the target. In general, it is possible for
the JTAG controller to be unresponsive until the target is set up
at91sam3u4e.cfg lpc1768.cfg sharp_lh79532.cfg
at91sam3uXX.cfg lpc2103.cfg smdk6410.cfg
at91sam7sx.cfg lpc2124.cfg smp8634.cfg
-at91sam9260.cfg lpc2129.cfg stm32.cfg
+at91sam9260.cfg lpc2129.cfg stm32f1x.cfg
c100.cfg lpc2148.cfg str710.cfg
c100config.tcl lpc2294.cfg str730.cfg
c100helper.tcl lpc2378.cfg str750.cfg
$_TARGETNAME configure -work-area-phys 0x00200000 \
-work-area-size 0x4000 -work-area-backup 0
@end example
-@pxref{Define CPU targets working in SMP}
+
@anchor{Define CPU targets working in SMP}
@subsection Define CPU targets working in SMP
@cindex SMP
@end example
@end deffn
+@deffn {Interface Driver} {remote_bitbang}
+Drive JTAG from a remote process. This sets up a UNIX or TCP socket connection
+with a remote process and sends ASCII encoded bitbang requests to that process
+instead of directly driving JTAG.
+
+The remote_bitbang driver is useful for debugging software running on
+processors which are being simulated.
+
+@deffn {Config Command} {remote_bitbang_port} number
+Specifies the TCP port of the remote process to connect to or 0 to use UNIX
+sockets instead of TCP.
+@end deffn
+
+@deffn {Config Command} {remote_bitbang_host} hostname
+Specifies the hostname of the remote process to connect to using TCP, or the
+name of the UNIX socket to use if remote_bitbang_port is 0.
+@end deffn
+
+For example, to connect remotely via TCP to the host foobar you might have
+something like:
+
+@example
+interface remote_bitbang
+remote_bitbang_port 3335
+remote_bitbang_host foobar
+@end example
+
+To connect to another process running locally via UNIX sockets with socket
+named mysocket:
+
+@example
+interface remote_bitbang
+remote_bitbang_port 0
+remote_bitbang_host mysocket
+@end example
+@end deffn
+
@deffn {Interface Driver} {usb_blaster}
USB JTAG/USB-Blaster compatibles over one of the userspace libraries
for FTDI chips. These interfaces have several commands, used to
(Support for this is preliminary and incomplete.)
@item @code{cortex_a8} -- this is an ARMv7 core with an MMU
@item @code{cortex_m3} -- this is an ARMv7 core, supporting only the
-compact Thumb2 instruction set. It supports one variant:
-@itemize @minus
-@item @code{lm3s} ... Use this when debugging older Stellaris LM3S targets.
-This will cause OpenOCD to use a software reset rather than asserting
-SRST, to avoid a issue with clearing the debug registers.
-This is fixed in Fury Rev B, DustDevil Rev B, Tempest; these revisions will
-be detected and the normal reset behaviour used.
-@end itemize
+compact Thumb2 instruction set.
@item @code{dragonite} -- resembles arm966e
@item @code{dsp563xx} -- implements Freescale's 24-bit DSP.
(Support for this is still incomplete.)
@end quotation
@end deffn
-@deffn {Flash Driver} stm32x
-All members of the STM32 microcontroller family from ST Microelectronics
+@deffn {Flash Driver} stm32f1x
+All members of the STM32f1x microcontroller family from ST Microelectronics
include internal flash and use ARM Cortex M3 cores.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
@example
-flash bank $_FLASHNAME stm32x 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME
@end example
-Some stm32x-specific commands
-@footnote{Currently there is a @command{stm32x mass_erase} command.
+Some stm32f1x-specific commands
+@footnote{Currently there is a @command{stm32f1x mass_erase} command.
That seems pointless since the same effect can be had using the
standard @command{flash erase_address} command.}
are defined:
-@deffn Command {stm32x lock} num
+@deffn Command {stm32f1x lock} num
Locks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {stm32x unlock} num
+@deffn Command {stm32f1x unlock} num
Unlocks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {stm32x options_read} num
+@deffn Command {stm32f1x options_read} num
Read and display the stm32 option bytes written by
-the @command{stm32x options_write} command.
+the @command{stm32f1x options_write} command.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {stm32x options_write} num (@option{SWWDG}|@option{HWWDG}) (@option{RSTSTNDBY}|@option{NORSTSTNDBY}) (@option{RSTSTOP}|@option{NORSTSTOP})
+@deffn Command {stm32f1x options_write} num (@option{SWWDG}|@option{HWWDG}) (@option{RSTSTNDBY}|@option{NORSTSTNDBY}) (@option{RSTSTOP}|@option{NORSTSTOP})
Writes the stm32 option byte with the specified values.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@end deffn
+@deffn {Flash Driver} stm32f2x
+All members of the STM32f2x microcontroller family from ST Microelectronics
+include internal flash and use ARM Cortex M3 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+@end deffn
+
@deffn {Flash Driver} str7x
All members of the STR7 microcontroller family from ST Microelectronics
include internal flash and use ARM7TDMI cores.
@end example
@end deffn
+@deffn {Flash Driver} fm3
+All members of the FM3 microcontroller family from Fujitsu
+include internal flash and use ARM Cortex M3 cores.
+The @var{fm3} driver uses the @var{target} parameter to select the
+correct bank config, it can currently be one of the following:
+@code{mb9bfxx1.cpu}, @code{mb9bfxx2.cpu}, @code{mb9bfxx3.cpu},
+@code{mb9bfxx4.cpu}, @code{mb9bfxx5.cpu} or @code{mb9bfxx6.cpu}.
+
+@example
+flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME
+@end example
+@end deffn
+
@subsection str9xpec driver
@cindex str9xpec
projects / fw / openocd / blobdiff