tcl: add TP-LINK TL-MR3020 to the firmware recovery script

[fw/openocd] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 925eebed2d4406c490b3602d2149e7655ca4808a..95c20541924246d7b691c83f45f5a52836bbf552 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -288,12 +288,11 @@ communication between developers:
 
 @uref{https://lists.sourceforge.net/mailman/listinfo/openocd-devel}
 
-@section OpenOCD Bug Database
+@section OpenOCD Bug Tracker
 
-During the 0.4.x release cycle the OpenOCD project team began
-using Trac for its bug database:
+The OpenOCD Bug Tracker is hosted on SourceForge:
 
-@uref{https://sourceforge.net/apps/trac/openocd}
+@uref{https://sourceforge.net/p/openocd/tickets/}
 
 
 @node Debug Adapter Hardware
@@ -2585,6 +2584,11 @@ cmsis_dap_vid_pid 0xc251 0xf001 0x0d28 0x0204
 @end example
 @end deffn
 
+@deffn {Config Command} {cmsis_dap_serial} [serial]
+Specifies the @var{serial} of the CMSIS-DAP device to use.
+If not specified, serial numbers are not considered.
+@end deffn
+
 @deffn {Command} {cmsis-dap info}
 Display various device information, like hardware version, firmware version, current bus status.
 @end deffn
@@ -4839,6 +4843,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 
 @deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
 Write the image @file{filename} to the current target's flash bank(s).
+Only loadable sections from the image are written.
 A relocation @var{offset} may be specified, in which case it is added
 to the base address for each section in the image.
 The file [@var{type}] can be specified
@@ -5435,6 +5440,40 @@ This will remove any Code Protection.
 @end deffn
 @end deffn
 
+@deffn {Flash Driver} psoc4
+All members of the PSoC 41xx/42xx microcontroller family from Cypress
+include internal flash and use ARM Cortex M0 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+Note: Erased internal flash reads as 00.
+System ROM of PSoC 4 does not implement erase of a flash sector.
+
+@example
+flash bank $_FLASHNAME psoc4 0 0 0 0 $_TARGETNAME
+@end example
+
+psoc4-specific commands
+@deffn Command {psoc4 flash_autoerase} num (on|off)
+Enables or disables autoerase mode for a flash bank.
+
+If flash_autoerase is off, use mass_erase before flash programming.
+Flash erase command fails if region to erase is not whole flash memory.
+
+If flash_autoerase is on, a sector is both erased and programmed in one
+system ROM call. Flash erase command is ignored.
+This mode is suitable for gdb load.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {psoc4 mass_erase} num
+Erases the contents of the flash memory, protection and security lock.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
 @deffn {Flash Driver} stellaris
 All members of the Stellaris LM3Sxxx microcontroller family from
 Texas Instruments
@@ -5546,17 +5585,28 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 
 @deffn {Flash Driver} stm32lx
 All members of the STM32L microcontroller families from ST Microelectronics
-include internal flash and use ARM Cortex-M3 cores.
+include internal flash and use ARM Cortex-M3 and Cortex-M0+ cores.
 The driver automatically recognizes a number of these chips using
 the chip identification register, and autoconfigures itself.
 
 Note that some devices have been found that have a flash size register that contains
 an invalid value, to workaround this issue you can override the probed value used by
-the flash driver.
+the flash driver. If you use 0 as the bank base address, it tells the
+driver to autodetect the bank location assuming you're configuring the
+second bank.
 
 @example
-flash bank $_FLASHNAME stm32lx 0 0x20000 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32lx 0x08000000 0x20000 0 0 $_TARGETNAME
 @end example
+
+Some stm32lx-specific commands are defined:
+
+@deffn Command {stm32lx mass_erase} num
+Mass erases the entire stm32lx device (all flash banks and EEPROM
+data). This is the only way to unlock a protected flash (unless RDP
+Level is 2 which can't be unlocked at all).
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
 @end deffn
 
 @deffn {Flash Driver} str7x