Specifies the adapter layout to use.
@end deffn
-@deffn {Config Command} {hla_vid_pid} vid pid
-The vendor ID and product ID of the device.
+@deffn {Config Command} {hla_vid_pid} [vid pid]+
+Pairs of vendor IDs and product IDs of the device.
@end deffn
@deffn {Command} {hla_command} command
released on the scan chain.
@item @b{reset-end}
@* Issued as the final step in @command{reset} processing.
-@ignore
-@item @b{reset-halt-post}
-@* Currently not used
-@item @b{reset-halt-pre}
-@* Currently not used
-@end ignore
@item @b{reset-init}
@* Used by @b{reset init} command for board-specific initialization.
This event fires after @emph{reset-deassert-post}.
This is the most robust place to use @command{jtag_rclk}
or @command{adapter_khz} to switch to a low JTAG clock rate,
when reset disables PLLs needed to use a fast clock.
-@ignore
-@item @b{reset-wait-pos}
-@* Currently not used
-@item @b{reset-wait-pre}
-@* Currently not used
-@end ignore
@item @b{resume-start}
@* Before any target is resumed
@item @b{resume-end}
@end example
@end deffn
+@deffn {Flash Driver} xcf
+@cindex Xilinx Platform flash driver
+@cindex xcf
+Xilinx FPGAs can be configured from specialized flash ICs named Platform Flash.
+It is (almost) regular NOR flash with erase sectors, program pages, etc. The
+only difference is special registers controlling its FPGA specific behavior.
+They must be properly configured for successful FPGA loading using
+additional @var{xcf} driver command:
+
+@deffn Command {xcf ccb} <bank_id>
+command accepts additional parameters:
+@itemize
+@item @var{external|internal} ... selects clock source.
+@item @var{serial|parallel} ... selects serial or parallel data bus mode.
+@item @var{slave|master} ... selects slave of master mode for flash device.
+@item @var{40|20} ... selects clock frequency in MHz for internal clock
+in master mode.
+@end itemize
+@example
+xcf ccb 0 external parallel slave 40
+@end example
+All of them must be specified even if clock frequency is pointless
+in slave mode. If only bank id specified than command prints current
+CCB register value. Note: there is no need to write this register
+every time you erase/program data sectors because it stores in
+dedicated sector.
+@end deffn
+
+@deffn Command {xcf configure} <bank_id>
+Initiates FPGA loading procedure. Useful if your board has no "configure"
+button.
+@example
+xcf configure 0
+@end example
+@end deffn
+
+Additional driver notes:
+@itemize
+@item Only single revision supported.
+@item Driver automatically detects need of bit reverse, but
+only "bin" (raw binary, do not confuse it with "bit") and "mcs"
+(Intel hex) file types supported.
+@item For additional info check xapp972.pdf and ug380.pdf.
+@end itemize
+@end deffn
+
@deffn {Flash Driver} lpcspifi
@cindex NXP SPI Flash Interface
@cindex SPIFI
families from Texas Instruments include internal flash. The driver
automatically recognizes a number of these chips using the chip
identification register, and autoconfigures itself.
-@footnote{Currently there is a @command{stellaris mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
@example
flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
@end example
-Some stm32f1x-specific commands
-@footnote{Currently there is a @command{stm32f1x mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
-are defined:
+Some stm32f1x-specific commands are defined:
@deffn Command {stm32f1x lock} num
Locks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {stm32f1x mass_erase} num
+Mass erases the entire stm32f1x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32f1x options_read} num
Read and display the stm32 option bytes written by
the @command{stm32f1x options_write} command.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
+@example
+flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
+@end example
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {stm32f2x mass_erase} num
+Mass erases the entire stm32f2x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32f2x options_read} num
Reads and displays user options and (where implemented) boot_addr0, boot_addr1, optcr2.
The @var{num} parameter is a value shown by @command{flash banks}.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
+@example
+flash bank $_FLASHNAME stm32h7x 0 0 0 0 $_TARGETNAME
+@end example
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver.
Unlocks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+
+@deffn Command {stm32h7x mass_erase} num
+Mass erases the entire stm32h7x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
@end deffn
@deffn {Flash Driver} stm32lx
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
+@example
+flash bank $_FLASHNAME stm32lx 0 0 0 0 $_TARGETNAME
+@end example
+
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
the flash driver. If you use 0 as the bank base address, it tells the
Some stm32lx-specific commands are defined:
+@deffn Command {stm32lx lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32lx unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {stm32lx mass_erase} num
Mass erases the entire stm32lx device (all flash banks and EEPROM
data). This is the only way to unlock a protected flash (unless RDP
@end deffn
@end deffn
+@deffn {Flash Driver} stm32l4x
+All members of the STM32L4 microcontroller families from ST Microelectronics
+include internal flash and use ARM Cortex-M4 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32l4x 0x08000000 0x40000 0 0 $_TARGETNAME
+@end example
+
+Some stm32l4x-specific commands are defined:
+
+@deffn Command {stm32l4x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32l4x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32l4x mass_erase} num
+Mass erases the entire stm32l4x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} str7x
All members of the STR7 microcontroller family from ST Microelectronics
include internal flash and use ARM7TDMI cores.
In a debug session using JTAG for its transport protocol,
OpenOCD supports running such test files.
-@deffn Command {svf} filename [@option{quiet}]
+@deffn Command {svf} @file{filename} [@option{-tap @var{tapname}}] [@option{[-]quiet}] @
+ [@option{[-]nil}] [@option{[-]progress}] [@option{[-]ignore_error}]
This issues a JTAG reset (Test-Logic-Reset) and then
runs the SVF script from @file{filename}.
-Unless the @option{quiet} option is specified,
-each command is logged before it is executed.
+
+Arguments can be specified in any order; the optional dash doesn't
+affect their semantics.
+
+Command options:
+@itemize @minus
+@item @option{-tap @var{tapname}} ignore IR and DR headers and footers
+specified by the SVF file with HIR, TIR, HDR and TDR commands;
+instead, calculate them automatically according to the current JTAG
+chain configuration, targetting @var{tapname};
+@item @option{[-]quiet} do not log every command before execution;
+@item @option{[-]nil} ``dry run'', i.e., do not perform any operations
+on the real interface;
+@item @option{[-]progress} enable progress indication;
+@item @option{[-]ignore_error} continue execution despite TDO check
+errors.
+@end itemize
@end deffn
@section XSVF: Xilinx Serial Vector Format
projects / fw / openocd / blobdiff