and are not restricted to containing only decimal digits.)
@end deffn
+@deffn {Config Command} {ftdi_location} <bus>:<port>[,<port>]...
+Specifies the physical USB port of the adapter to use. The path
+roots at @var{bus} and walks down the physical ports, with each
+@var{port} option specifying a deeper level in the bus topology, the last
+@var{port} denoting where the target adapter is actually plugged.
+The USB bus topology can be queried with the command @emph{lsusb -t}.
+
+This command is only available if your libusb1 is at least version 1.0.16.
+@end deffn
+
@deffn {Config Command} {ftdi_channel} channel
Selects the channel of the FTDI device to use for MPSSE operations. Most
adapters use the default, channel 0, but there are exceptions.
@item @var{jedec_probe} ... is used to detect certain non-CFI flash ROMs,
like AM29LV010 and similar types.
@item @var{x16_as_x8} ... when a 16-bit flash is hooked up to an 8-bit bus.
+@item @var{bus_swap} ... when data bytes in a 16-bit flash needs to be swapped.
@end itemize
To configure two adjacent banks of 16 MBytes each, both sixteen bits (two bytes)
@end example
@end deffn
+@deffn {Flash Driver} kinetis
+@cindex kinetis
+Kx and KLx members of the Kinetis microcontroller family from Freescale include
+internal flash and use ARM Cortex M0+ or M4 cores. The driver automatically
+recognizes flash size and a number of flash banks (1-4) using the chip
+identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME kinetis 0 0 0 0 $_TARGETNAME
+@end example
+
+@deffn Command {kinetis mdm check_security}
+Checks status of device security lock. Used internally in examine-end event.
+@end deffn
+
+@deffn Command {kinetis mdm mass_erase}
+Issues a complete Flash erase via the MDM-AP.
+This can be used to erase a chip back to its factory state.
+Command removes security lock from a device (use of SRST highly recommended).
+It does not require the processor to be halted.
+@end deffn
+
+@deffn Command {kinetis nvm_partition}
+For FlexNVM devices only (KxxDX and KxxFX).
+Command shows or sets data flash or EEPROM backup size in kilobytes,
+sets two EEPROM blocks sizes in bytes and enables/disables loading
+of EEPROM contents to FlexRAM during reset.
+
+For details see device reference manual, Flash Memory Module,
+Program Partition command.
+
+Setting is possible only once after mass_erase.
+Reset the device after partition setting.
+
+Show partition size:
+@example
+kinetis nvm_partition info
+@end example
+
+Set 32 KB data flash, rest of FlexNVM is EEPROM backup. EEPROM has two blocks
+of 512 and 1536 bytes and its contents is loaded to FlexRAM during reset:
+@example
+kinetis nvm_partition dataflash 32 512 1536 on
+@end example
+
+Set 16 KB EEPROM backup, rest of FlexNVM is a data flash. EEPROM has two blocks
+of 1024 bytes and its contents is not loaded to FlexRAM during reset:
+@example
+kinetis nvm_partition eebkp 16 1024 1024 off
+@end example
+@end deffn
+
+@deffn Command {kinetis disable_wdog}
+For Kx devices only (KLx has different COP watchdog, it is not supported).
+Command disables watchdog timer.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} kinetis_ke
+@cindex kinetis_ke
+KE members of the Kinetis microcontroller family from Freescale include
+internal flash and use ARM Cortex M0+. The driver automatically recognizes
+the KE family and sub-family using the chip identification register, and
+autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME kinetis_ke 0 0 0 0 $_TARGETNAME
+@end example
+
+@deffn Command {kinetis_ke mdm check_security}
+Checks status of device security lock. Used internally in examine-end event.
+@end deffn
+
+@deffn Command {kinetis_ke mdm mass_erase}
+Issues a complete Flash erase via the MDM-AP.
+This can be used to erase a chip back to its factory state.
+Command removes security lock from a device (use of SRST highly recommended).
+It does not require the processor to be halted.
+@end deffn
+
+@deffn Command {kinetis_ke disable_wdog}
+Command disables watchdog timer.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} fm4
+All members of the FM4 microcontroller family from Spansion (formerly Fujitsu)
+include internal flash and use ARM Cortex-M4 cores.
+The @var{fm4} driver uses a @var{family} parameter to select the
+correct bank config, it can currently be one of the following:
+@code{MB9BFx64}, @code{MB9BFx65}, @code{MB9BFx66}, @code{MB9BFx67}, @code{MB9BFx68},
+@code{S6E2Cx8}, @code{S6E2Cx9}, @code{S6E2CxA} or @code{S6E2Dx},
+with @code{x} treated as wildcard and otherwise case (and any trailing
+characters) ignored.
+
+@example
+flash bank $@{_FLASHNAME@}0 fm4 0x00000000 0 0 0 $_TARGETNAME S6E2CCAJ0A
+flash bank $@{_FLASHNAME@}1 fm4 0x00100000 0 0 0 $_TARGETNAME S6E2CCAJ0A
+@end example
+@emph{The current implementation is incomplete. Protection is not supported,
+nor is Chip Erase (only Sector Erase is implemented).}
+@end deffn
+
@deffn {Flash Driver} lpc2000
This is the driver to support internal flash of all members of the
LPC11(x)00 and LPC1300 microcontroller families and most members of
@end deffn
@end deffn
+@deffn {Flash Driver} xmc1xxx
+All members of the XMC1xxx microcontroller family from Infineon.
+This driver does not require the chip and bus width to be specified.
+@end deffn
+
@deffn {Flash Driver} xmc4xxx
All members of the XMC4xxx microcontroller family from Infineon.
This driver does not require the chip and bus width to be specified.
projects / fw / openocd / blobdiff