All changes in the OpenOCD Git repository go through the web-based Gerrit
Code Review System:
-@uref{http://openocd.zylin.com/}
+@uref{https://review.openocd.org/}
After a one-time registration and repository setup, anyone can push commits
from their local Git repository directly into Gerrit.
These interfaces have several commands, used to configure the driver
before initializing the JTAG scan chain:
-@deffn {Config Command} {ft232r_vid_pid} @var{vid} @var{pid}
+@deffn {Config Command} {ft232r vid_pid} @var{vid} @var{pid}
The vendor ID and product ID of the adapter. If not specified, default
0x0403:0x6001 is used.
@end deffn
-@deffn {Config Command} {ft232r_serial_desc} @var{serial}
+@deffn {Config Command} {ft232r serial_desc} @var{serial}
Specifies the @var{serial} of the adapter to use, in case the
vendor provides unique IDs and more than one adapter is connected to
the host. If not specified, serial numbers are not considered.
@end deffn
-@deffn {Config Command} {ft232r_jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
+@deffn {Config Command} {ft232r jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
Set four JTAG GPIO numbers at once.
If not specified, default 0 3 1 2 or TXD CTS RXD RTS is used.
@end deffn
-@deffn {Config Command} {ft232r_tck_num} @var{tck}
+@deffn {Config Command} {ft232r tck_num} @var{tck}
Set TCK GPIO number. If not specified, default 0 or TXD is used.
@end deffn
-@deffn {Config Command} {ft232r_tms_num} @var{tms}
+@deffn {Config Command} {ft232r tms_num} @var{tms}
Set TMS GPIO number. If not specified, default 3 or CTS is used.
@end deffn
-@deffn {Config Command} {ft232r_tdi_num} @var{tdi}
+@deffn {Config Command} {ft232r tdi_num} @var{tdi}
Set TDI GPIO number. If not specified, default 1 or RXD is used.
@end deffn
-@deffn {Config Command} {ft232r_tdo_num} @var{tdo}
+@deffn {Config Command} {ft232r tdo_num} @var{tdo}
Set TDO GPIO number. If not specified, default 2 or RTS is used.
@end deffn
-@deffn {Config Command} {ft232r_trst_num} @var{trst}
+@deffn {Config Command} {ft232r trst_num} @var{trst}
Set TRST GPIO number. If not specified, default 4 or DTR is used.
@end deffn
-@deffn {Config Command} {ft232r_srst_num} @var{srst}
+@deffn {Config Command} {ft232r srst_num} @var{srst}
Set SRST GPIO number. If not specified, default 6 or DCD is used.
@end deffn
-@deffn {Config Command} {ft232r_restore_serial} @var{word}
+@deffn {Config Command} {ft232r restore_serial} @var{word}
Restore serial port after JTAG. This USB bitmode control word
(16-bit) will be sent before quit. Lower byte should
set GPIO direction register to a "sane" state:
@deffn {Config Command} {st-link vid_pid} [vid pid]+
Pairs of vendor IDs and product IDs of the device.
@end deffn
+
+@deffn {Command} {st-link cmd} rx_n (tx_byte)+
+Sends an arbitrary command composed by the sequence of bytes @var{tx_byte}
+and receives @var{rx_n} bytes.
+
+For example, the command to read the target's supply voltage is one byte 0xf7 followed
+by 15 bytes zero. It returns 8 bytes, where the first 4 bytes represent the ADC sampling
+of the reference voltage 1.2V and the last 4 bytes represent the ADC sampling of half
+the target's supply voltage.
+@example
+> st-link cmd 8 0xf7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+0xf1 0x05 0x00 0x00 0x0b 0x08 0x00 0x00
+@end example
+The result can be converted to Volts (ignoring the most significant bytes, always zero)
+@example
+> set a [st-link cmd 8 0xf7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0]
+> echo [expr 2*1.2*([lindex $a 4]+256*[lindex $a 5])/([lindex $a 0]+256*[lindex $a 1])]
+3.24891518738
+@end example
+@end deffn
@end deffn
@deffn {Interface Driver} {opendous}
@end deffn
+@deffn {Flash Driver} {npcx}
+All versions of the NPCX microcontroller families from Nuvoton include internal
+flash. The NPCX flash driver supports the NPCX family of devices. The driver
+automatically recognizes the specific version's flash parameters and
+autoconfigures itself. The flash bank starts at address 0x64000000.
+
+@example
+flash bank $_FLASHNAME npcx 0x64000000 0 0 0 $_TARGETNAME
+@end example
+@end deffn
+
@deffn {Flash Driver} {nrf5}
All members of the nRF51 microcontroller families from Nordic Semiconductor
include internal flash and use ARM Cortex-M0 core.
@end deffn
@deffn {Flash Driver} {stm32l4x}
-All members of the STM32 G0, G4, L4, L4+, L5, WB and WL
+All members of the STM32 G0, G4, L4, L4+, L5, U5, WB and WL
microcontroller families from STMicroelectronics include internal flash
and use ARM Cortex-M0+, M4 and M33 cores.
The driver automatically recognizes a number of these chips using
@deffn {Command} {stm32l4x lock} num
Locks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
+
+@emph{Note:} To apply the protection change immediately, use @command{stm32l4x option_load}.
@end deffn
@deffn {Command} {stm32l4x unlock} num
Unlocks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
+
+@emph{Note:} To apply the protection change immediately, use @command{stm32l4x option_load}.
@end deffn
@deffn {Command} {stm32l4x mass_erase} num
is the register offset of the Option byte to write, and @var{reg_mask} is the mask
to apply when writing the register (only bits with a '1' will be touched).
+@emph{Note:} To apply the option bytes change immediately, use @command{stm32l4x option_load}.
+
For example to write the WRP1AR option bytes:
@example
stm32l4x option_write 0 0x28 0x00FF0000 0x00FF00FF
Forces a re-load of the option byte registers. Will cause a system reset of the device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+
+@deffn Command {stm32l4x trustzone} num [@option{enable} | @option{disable}]
+Enables or disables Global TrustZone Security, using the TZEN option bit.
+If neither @option{enabled} nor @option{disable} are specified, the command will display
+the TrustZone status.
+@emph{Note:} This command works only with devices with TrustZone, eg. STM32L5.
+@emph{Note:} This command will perform an OBL_Launch after modifying the TZEN.
+@end deffn
@end deffn
@deffn {Flash Driver} {str7x}
projects / fw / openocd / blobdiff