jtag/xds110: switch to command 'adapter serial'

[fw/openocd] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 286943643798e9a8017a0d9e7476be39ac851dea..78451c71c07fa05e436bd9641fc2d5771c8fad73 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2370,9 +2370,10 @@ This command is only available if your libusb1 is at least version 1.0.16.
 @deffn {Config Command} {adapter serial} serial_string
 Specifies the @var{serial_string} of the adapter to use.
 If this command is not specified, serial strings are not checked.
-No adapter uses this command, so far.
+Only the following adapter drivers use the serial string from this command:
+cmsis_dap, ft232r, ftdi, kitprog, presto, vsllink, xds110.
 The following adapters have their own command to specify the serial string:
-cmsis_dap, ft232r, ftdi, hla, jlink, kitprog, presto, st-link, vsllink, xds110.
+hla, jlink, st-link.
 @end deffn
 
 @section Interface Drivers
@@ -2427,11 +2428,6 @@ cmsis_dap_vid_pid 0xc251 0xf001 0x0d28 0x0204
 @end example
 @end deffn
 
-@deffn {Config Command} {cmsis_dap_serial} [serial]
-Specifies the @var{serial} of the CMSIS-DAP device to use.
-If not specified, serial numbers are not considered.
-@end deffn
-
 @deffn {Config Command} {cmsis_dap_backend} [@option{auto}|@option{usb_bulk}|@option{hid}]
 Specifies how to communicate with the adapter:
 
@@ -2516,15 +2512,6 @@ of the adapter. If not specified, the device description is ignored
 during device selection.
 @end deffn
 
-@deffn {Config Command} {ftdi serial} serial-number
-Specifies the @var{serial-number} of the adapter to use,
-in case the vendor provides unique IDs and more than one adapter
-is connected to the host.
-If not specified, serial numbers are not considered.
-(Note that USB serial numbers can be arbitrary Unicode strings,
-and are not restricted to containing only decimal digits.)
-@end deffn
-
 @deffn {Config Command} {ftdi channel} channel
 Selects the channel of the FTDI device to use for MPSSE operations. Most
 adapters use the default, channel 0, but there are exceptions.
@@ -2645,12 +2632,6 @@ The vendor ID and product ID of the adapter. If not specified, default
 0x0403:0x6001 is used.
 @end deffn
 
-@deffn {Config Command} {ft232r serial_desc} @var{serial}
-Specifies the @var{serial} of the adapter to use, in case the
-vendor provides unique IDs and more than one adapter is connected to
-the host. If not specified, serial numbers are not considered.
-@end deffn
-
 @deffn {Config Command} {ft232r jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
 Set four JTAG GPIO numbers at once.
 If not specified, default 0 3 1 2 or TXD CTS RXD RTS is used.
@@ -2915,11 +2896,6 @@ Indicate that a PSoC acquisition sequence needs to be run during adapter init.
 Please be aware that the acquisition sequence hard-resets the target.
 @end deffn
 
-@deffn {Config Command} {kitprog_serial} serial
-Select a KitProg device by its @var{serial}. If left unspecified, the first
-device detected by OpenOCD will be used.
-@end deffn
-
 @deffn {Command} {kitprog acquire_psoc}
 Run a PSoC acquisition sequence immediately. Typically, this should not be used
 outside of the target-specific configuration scripts since it hard-resets the
@@ -3034,9 +3010,6 @@ parport cable wiggler
 
 @deffn {Interface Driver} {presto}
 ASIX PRESTO USB JTAG programmer.
-@deffn {Config Command} {presto serial} serial_string
-Configures the USB serial number of the Presto device to use.
-@end deffn
 @end deffn
 
 @deffn {Interface Driver} {rlink}
@@ -3168,11 +3141,6 @@ LaunchPad evaluation boards. The XDS110 is also available as a stand-alone USB
 debug probe with the added capability to supply power to the target board. The
 following commands are supported by the XDS110 driver:
 
-@deffn {Config Command} {xds110 serial} serial_string
-Specifies the serial number of which XDS110 probe to use. Otherwise, the first
-XDS110 found will be used.
-@end deffn
-
 @deffn {Config Command} {xds110 supply} voltage_in_millivolts
 Available only on the XDS110 stand-alone probe. Sets the voltage level of the
 XDS110 power supply. A value of 0 leaves the supply off. Otherwise, the supply