@item @b{imx_gpio}
@* A NXP i.MX-based board (e.g. Wandboard) using the GPIO pins (should work on any i.MX processor).
+@item @b{am335xgpio}
+@* A Texas Instruments AM335x-based board (e.g. BeagleBone Black) using the GPIO pins of the expansion headers.
+
@item @b{jtag_vpi}
@* A JTAG driver acting as a client for the JTAG VPI server interface.
@* Link: @url{http://github.com/fjullien/jtag_vpi}
@item @b{vdebug}
@* A driver for Cadence virtual Debug Interface to emulated or simulated targets.
It implements a client connecting to the vdebug server, which in turn communicates
-with the emulated or simulated RTL model through a transactor. The current version
-supports only JTAG as a transport, but other virtual transports, like DAP are planned.
+with the emulated or simulated RTL model through a transactor. The driver supports
+JTAG and DAP-level transports.
@item @b{jtag_dpi}
@* A JTAG driver acting as a client for the SystemVerilog Direct Programming
@* A bitbang JTAG driver using Linux legacy sysfs GPIO.
This is deprecated from Linux v5.3; prefer using @b{linuxgpiod}.
+@item @b{esp_usb_jtag}
+@* A JTAG driver to communicate with builtin debug modules of Espressif ESP32-C3 and ESP32-S3 chips using OpenOCD.
+
@end itemize
@node About Jim-Tcl
@deffnx {Config Command} {pld init}
@deffnx {Command} {tpiu init}
@end deffn
+
+At last, @command{init} executes all the commands that are specified in
+the TCL list @var{post_init_commands}. The commands are executed in the
+same order they occupy in the list. If one of the commands fails, then
+the error is propagated and OpenOCD fails too.
+@example
+lappend post_init_commands @{echo "OpenOCD successfully initialized."@}
+lappend post_init_commands @{echo "Have fun with OpenOCD !"@}
+@end example
@end deffn
@deffn {Config Command} {noinit}
the hardware can support.
@end deffn
+@anchor{adapter gpio}
+@deffn {Config Command} {adapter gpio [ @
+ @option{tdo} | @option{tdi} | @option{tms} | @option{tck} | @option{trst} | @
+ @option{swdio} | @option{swdio_dir} | @option{swclk} | @option{srst} | @
+ @option{led} @
+ [ @
+ gpio_number | @option{-chip} chip_number | @
+ @option{-active-high} | @option{-active-low} | @
+ @option{-push-pull} | @option{-open-drain} | @option{-open-source} | @
+ @option{-pull-none} | @option{-pull-up} | @option{-pull-down} | @
+ @option{-init-inactive} | @option{-init-active} | @option{-init-input} @
+ ] ]}
+
+Define the GPIO mapping that the adapter will use. The following signals can be
+defined:
+
+@itemize @minus
+@item @option{tdo}, @option{tdi}, @option{tms}, @option{tck}, @option{trst}:
+JTAG transport signals
+@item @option{swdio}, @option{swclk}: SWD transport signals
+@item @option{swdio_dir}: optional swdio buffer control signal
+@item @option{srst}: system reset signal
+@item @option{led}: optional activity led
+
+@end itemize
+Some adapters require that the GPIO chip number is set in addition to the GPIO
+number. The configuration options enable signals to be defined as active-high or
+active-low. The output drive mode can be set to push-pull, open-drain or
+open-source. Most adapters will have to emulate open-drain or open-source drive
+modes by switching between an input and output. Input and output signals can be
+instructed to use a pull-up or pull-down resistor, assuming it is supported by
+the adaptor driver and hardware. The initial state of outputs may also be set,
+"active" state means 1 for active-high outputs and 0 for active-low outputs.
+Bidirectional signals may also be initialized as an input. If the swdio signal
+is buffered the buffer direction can be controlled with the swdio_dir signal;
+the active state means that the buffer should be set as an output with respect
+to the adapter. The command options are cumulative with later commands able to
+override settings defined by earlier ones. The two commands @command{gpio led 7
+-active-high} and @command{gpio led -chip 1 -active-low} sent sequentially are
+equivalent to issuing the single command @command{gpio led 7 -chip 1
+-active-low}. It is not permissible to set the drive mode or initial state for
+signals which are inputs. The drive mode for the srst and trst signals must be
+set with the @command{adapter reset_config} command. It is not permissible to
+set the initial state of swdio_dir as it is derived from the initial state of
+swdio. The command @command{adapter gpio} prints the current configuration for
+all GPIOs while the command @command{adapter gpio gpio_name} prints the current
+configuration for gpio_name. Not all adapters support this generic GPIO mapping,
+some require their own commands to define the GPIOs used. Adapters that support
+the generic mapping may not support all of the listed options.
+@end deffn
@deffn {Command} {adapter name}
Returns the name of the debug adapter driver being used.
@end deffn
+@deffn {Interface Driver} {am335xgpio} The AM335x SoC is present in BeagleBone
+Black and BeagleBone Green single-board computers which expose some of the GPIOs
+on the two expansion headers.
+
+For maximum performance the driver accesses memory-mapped GPIO peripheral
+registers directly. The memory mapping requires read and write permission to
+kernel memory; if /dev/gpiomem exists it will be used, otherwise /dev/mem will
+be used. The driver restores the GPIO state on exit.
+
+All four GPIO ports are available. GPIO configuration is handled by the generic
+command @ref{adapter gpio, @command{adapter gpio}}.
+
+@deffn {Config Command} {am335xgpio speed_coeffs} @var{speed_coeff} @var{speed_offset}
+Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified
+speed_coeff defaults to 600000 and speed_offset defaults to 575.
+@end deffn
+
+See @file{interface/beaglebone-swd-native.cfg} for a sample configuration file.
+
+@end deffn
+
+
@deffn {Interface Driver} {linuxgpiod}
Linux provides userspace access to GPIO through libgpiod since Linux kernel version v4.6.
-The driver emulates either JTAG and SWD transport through bitbanging.
+The driver emulates either JTAG or SWD transport through bitbanging.
See @file{interface/dln-2-gpiod.cfg} for a sample config.
+
+@deffn {Config Command} {linuxgpiod gpiochip} @var{chip}
+Set the GPIO chip number for all GPIOs used by linuxgpiod. If GPIOs use
+different GPIO chips then the individual GPIO configuration commands (i.e., not
+@command{linuxgpiod jtag_nums} or @command{linuxgpiod swd_nums}) can be used to
+set chip numbers independently for each GPIO.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
+Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order). Must
+be specified to enable JTAG transport. These pins can also be specified
+individually.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod tck_num} [@var{chip}] @var{tck}
+Set TCK GPIO number, and optionally TCK chip number. Must be specified to enable
+JTAG transport. Can also be specified using the configuration command
+@command{linuxgpiod jtag_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod tms_num} [@var{chip}] @var{tms}
+Set TMS GPIO number, and optionally TMS chip number. Must be specified to enable
+JTAG transport. Can also be specified using the configuration command
+@command{linuxgpiod jtag_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod tdo_num} [@var{chip}] @var{tdo}
+Set TDO GPIO number, and optionally TDO chip number. Must be specified to enable
+JTAG transport. Can also be specified using the configuration command
+@command{linuxgpiod jtag_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod tdi_num} [@var{chip}] @var{tdi}
+Set TDI GPIO number, and optionally TDI chip number. Must be specified to enable
+JTAG transport. Can also be specified using the configuration command
+@command{linuxgpiod jtag_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod trst_num} [@var{chip}] @var{trst}
+Set TRST GPIO number, and optionally TRST chip number. Must be specified to
+enable TRST.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod swd_nums} @var{swclk} @var{swdio}
+Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
+specified to enable SWD transport. These pins can also be specified
+individually.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod swclk_num} [@var{chip}] @var{swclk}
+Set SWCLK GPIO number, and optionally SWCLK chip number. Must be specified to
+enable SWD transport. Can also be specified using the configuration command
+@command{linuxgpiod swd_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod swdio_num} [@var{chip}] @var{swdio}
+Set SWDIO GPIO number, and optionally SWDIO chip number. Must be specified to
+enable SWD transport. Can also be specified using the configuration command
+@command{linuxgpiod swd_nums}.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod swdio_dir_num} [@var{chip}] @var{swdio_dir}
+Set SWDIO direction control GPIO number, and optionally SWDIO direction control
+chip number. If specified, this GPIO can be used to control the direction of an
+external buffer connected to the SWDIO GPIO (set=output mode, clear=input mode).
+@end deffn
+
+@deffn {Config Command} {linuxgpiod srst_num} [@var{chip}] @var{srst}
+Set SRST GPIO number, and optionally SRST chip number. Must be specified to
+enable SRST.
+@end deffn
+
+@deffn {Config Command} {linuxgpiod led_num} [@var{chip}] @var{led}
+Set activity LED GPIO number, and optionally activity LED chip number. If not
+specified an activity LED is not enabled.
+@end deffn
+
@end deffn
@end deffn
+@deffn {Interface Driver} {esp_usb_jtag}
+Espressif JTAG driver to communicate with ESP32-C3, ESP32-S3 chips and ESP USB Bridge board using OpenOCD.
+These chips have built-in JTAG circuitry and can be debugged without any additional hardware.
+Only an USB cable connected to the D+/D- pins is necessary.
+
+@deffn {Config Command} {espusbjtag tdo}
+Returns the current state of the TDO line
+@end deffn
+
+@deffn {Config Command} {espusbjtag setio} setio
+Manually set the status of the output lines with the order of (tdi tms tck trst srst)
+@example
+espusbjtag setio 0 1 0 1 0
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag vid_pid} vid_pid
+Set vendor ID and product ID for the ESP usb jtag driver
+@example
+espusbjtag vid_pid 0x303a 0x1001
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag caps_descriptor} caps_descriptor
+Set the jtag descriptor to read capabilities of ESP usb jtag driver
+@example
+espusbjtag caps_descriptor 0x2000
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag chip_id} chip_id
+Set chip id to transfer to the ESP USB bridge board
+@example
+espusbjtag chip_id 1
+@end example
+@end deffn
+
+@end deffn
@section Transport Configuration
@cindex Transport
A DAP may also provide optional @var{configparams}:
@itemize @bullet
+@item @code{-adiv5}
+Specify that it's an ADIv5 DAP. This is the default if not specified.
+@item @code{-adiv6}
+Specify that it's an ADIv6 DAP.
@item @code{-ignore-syspwrupack}
-@*Specify this to ignore the CSYSPWRUPACK bit in the ARM DAP DP CTRL/STAT
+Specify this to ignore the CSYSPWRUPACK bit in the ARM DAP DP CTRL/STAT
register during initial examination and when checking the sticky error bit.
This bit is normally checked after setting the CSYSPWRUPREQ bit, but some
devices do not set the ack bit until sometime later.
for TCL scripting.
@end deffn
-@deffn {Command} {dap info} [num]
+@deffn {Command} {dap info} [@var{num}|@option{root}]
Displays the ROM table for MEM-AP @var{num},
defaulting to the currently selected AP of the currently selected target.
+On ADIv5 DAP @var{num} is the numeric index of the AP.
+On ADIv6 DAP @var{num} is the base address of the AP.
+With ADIv6 only, @option{root} specifies the root ROM table.
@end deffn
@deffn {Command} {dap init}
The following commands exist as subcommands of DAP instances:
-@deffn {Command} {$dap_name info} [num]
+@deffn {Command} {$dap_name info} [@var{num}|@option{root}]
Displays the ROM table for MEM-AP @var{num},
defaulting to the currently selected AP.
+On ADIv5 DAP @var{num} is the numeric index of the AP.
+On ADIv6 DAP @var{num} is the base address of the AP.
+With ADIv6 only, @option{root} specifies the root ROM table.
@end deffn
@deffn {Command} {$dap_name apid} [num]
Displays ID register from AP @var{num}, defaulting to the currently selected AP.
+On ADIv5 DAP @var{num} is the numeric index of the AP.
+On ADIv6 DAP @var{num} is the base address of the AP.
@end deffn
@anchor{DAP subcommand apreg}
@deffn {Command} {$dap_name apreg} ap_num reg [value]
Displays content of a register @var{reg} from AP @var{ap_num}
or set a new value @var{value}.
+On ADIv5 DAP @var{ap_num} is the numeric index of the AP.
+On ADIv6 DAP @var{ap_num} is the base address of the AP.
@var{reg} is byte address of a word register, 0, 4, 8 ... 0xfc.
@end deffn
@deffn {Command} {$dap_name apsel} [num]
Select AP @var{num}, defaulting to 0.
+On ADIv5 DAP @var{num} is the numeric index of the AP.
+On ADIv6 DAP @var{num} is the base address of the AP.
@end deffn
@deffn {Command} {$dap_name dpreg} reg [value]
@deffn {Command} {$dap_name baseaddr} [num]
Displays debug base address from MEM-AP @var{num},
defaulting to the currently selected AP.
+On ADIv5 DAP @var{num} is the numeric index of the AP.
+On ADIv6 DAP @var{num} is the base address of the AP.
@end deffn
@deffn {Command} {$dap_name memaccess} [value]
Disabled by default
@end deffn
+@deffn {Config Command} {$dap_name nu_npcx_quirks} [@option{enable}]
+Set/get quirks mode for Nuvoton NPCX/NPCD MCU families
+Disabled by default
+@end deffn
@node CPU Configuration
@chapter CPU Configuration
@item @code{dsp5680xx} -- implements Freescale's 5680x DSP.
@item @code{esirisc} -- this is an EnSilica eSi-RISC core.
The current implementation supports eSi-32xx cores.
+@item @code{esp32} -- this is an Espressif SoC with dual Xtensa cores.
+@item @code{esp32s2} -- this is an Espressif SoC with single Xtensa core.
+@item @code{esp32s3} -- this is an Espressif SoC with dual Xtensa cores.
@item @code{fa526} -- resembles arm920 (w/o Thumb).
@item @code{feroceon} -- resembles arm926.
@item @code{hla_target} -- a Cortex-M alternative to work with HL adapters like ST-Link.
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
-@var{rtos_type} can be one of @option{auto}, @option{eCos},
+@var{rtos_type} can be one of @option{auto}, @option{none}, @option{eCos},
@option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
@option{embKernel}, @option{mqx}, @option{uCOS-III}, @option{nuttx},
@option{RIOT}, @option{Zephyr}
scan and after a reset. A manual call to arp_examine is required to
access the target for debugging.
-@item @code{-ap-num} @var{ap_number} -- set DAP access port for target,
-@var{ap_number} is the numeric index of the DAP AP the target is connected to.
+@item @code{-ap-num} @var{ap_number} -- set DAP access port for target.
+On ADIv5 DAP @var{ap_number} is the numeric index of the DAP AP the target is connected to.
+On ADIv6 DAP @var{ap_number} is the base address of the DAP AP the target is connected to.
Use this option with systems where multiple, independent cores are connected
to separate access ports of the same DAP.
@end deffn
@deffn {Flash Driver} {bluenrg-x}
-STMicroelectronics BlueNRG-1, BlueNRG-2 and BlueNRG-LP Bluetooth low energy wireless system-on-chip. They include ARM Cortex-M0/M0+ core and internal flash memory.
+STMicroelectronics BlueNRG-1, BlueNRG-2 and BlueNRG-LP/LPS Bluetooth low energy wireless system-on-chip. They include ARM Cortex-M0/M0+ core and internal flash memory.
The driver automatically recognizes these chips using
the chip identification registers, and autoconfigures itself.
other). If option @option{error} is used, OpenOCD will return a
non-zero exit code to the parent process.
-Like any TCL commands, also @command{shutdown} can be redefined, e.g.:
+If user types CTRL-C or kills OpenOCD, the command @command{shutdown}
+will be automatically executed to cause OpenOCD to exit.
+
+It is possible to specify, in the TCL list @var{pre_shutdown_commands} , a
+set of commands to be automatically executed before @command{shutdown} , e.g.:
@example
-# redefine shutdown
-rename shutdown original_shutdown
-proc shutdown @{@} @{
- puts "This is my implementation of shutdown"
- # my own stuff before exit OpenOCD
- original_shutdown
-@}
+lappend pre_shutdown_commands @{echo "Goodbye, my friend ..."@}
+lappend pre_shutdown_commands @{echo "see you soon !"@}
@end example
-If user types CTRL-C or kills OpenOCD, either the command @command{shutdown}
-or its replacement will be automatically executed before OpenOCD exits.
+The commands in the list will be executed (in the same order they occupy
+in the list) before OpenOCD exits. If one of the commands in the list
+fails, then the remaining commands are not executed anymore while OpenOCD
+will proceed to quit.
@end deffn
@anchor{debuglevel}
@deffn {Command} {cti create} cti_name @option{-dap} dap_name @option{-ap-num} apn @option{-baseaddr} base_address
Creates a CTI instance @var{cti_name} on the DAP instance @var{dap_name} on MEM-AP
-@var{apn}. The @var{base_address} must match the base address of the CTI
+@var{apn}.
+On ADIv5 DAP @var{apn} is the numeric index of the DAP AP the CTI is connected to.
+On ADIv6 DAP @var{apn} is the base address of the DAP AP the CTI is connected to.
+The @var{base_address} must match the base address of the CTI
on the respective MEM-AP. All arguments are mandatory. This creates a
new command @command{$cti_name} which is used for various purposes
including additional configuration.
command.
@end deffn
+@deffn {Command} {arm semihosting_basedir} [dir]
+@cindex ARM semihosting
+Set the base directory for semihosting I/O, either an absolute path or a path relative to OpenOCD working directory.
+Use "." for the current directory.
+@end deffn
+
@section ARMv4 and ARMv5 Architecture
@cindex ARMv4
@cindex ARMv5
@item @code{-dap} @var{dap_name} -- names the DAP used to access this
TPIU. @xref{dapdeclaration,,DAP declaration}, on how to create and manage DAP instances.
-@item @code{-ap-num} @var{ap_number} -- sets DAP access port for TPIU,
-@var{ap_number} is the numeric index of the DAP AP the TPIU is connected to.
+@item @code{-ap-num} @var{ap_number} -- sets DAP access port for TPIU.
+On ADIv5 DAP @var{ap_number} is the numeric index of the DAP AP the TPIU is connected to.
+On ADIv6 DAP @var{ap_number} is the base address of the DAP AP the TPIU is connected to.
@item @code{-baseaddr} @var{base_address} -- sets the TPIU @var{base_address} where
to access the TPIU in the DAP AP memory space.
OpenOCD supports debugging STM8 through the STMicroelectronics debug
protocol SWIM, @pxref{swimtransport,,SWIM}.
+@section Xtensa Architecture
+Xtensa processors are based on a modular, highly flexible 32-bit RISC architecture
+that can easily scale from a tiny, cache-less controller or task engine to a high-performance
+SIMD/VLIW DSP provided by Cadence.
+@url{https://www.cadence.com/en_US/home/tools/ip/tensilica-ip/tensilica-xtensa-controllers-and-extensible-processors.html}.
+
+OpenOCD supports generic Xtensa processors implementation which can be customized by
+simply providing vendor-specific core configuration which controls every configurable
+Xtensa architecture option, e.g. number of address registers, exceptions, reduced
+size instructions support, memory banks configuration etc. Also OpenOCD supports SMP
+configurations for Xtensa processors with any number of cores and allows to configure
+their debug signals interconnection (so-called "break/stall networks") which control how
+debug signals are distributed among cores. Xtensa "break networks" are compatible with
+ARM's Cross Trigger Interface (CTI). For debugging code on Xtensa chips OpenOCD
+uses JTAG protocol. Currently OpenOCD implements several Epsressif Xtensa-based chips of
+@uref{https://www.espressif.com/en/products/socs, ESP32 family}.
+
+@subsection General Xtensa Commands
+
+@deffn {Command} {xtensa set_permissive} (0|1)
+By default accessing memory beyond defined regions is forbidden. This commnd controls memory access address check.
+When set to (1), skips access controls and address range check before read/write memory.
+@end deffn
+
+@deffn {Command} {xtensa maskisr} (on|off)
+Selects whether interrupts will be disabled during stepping over single instruction. The default configuration is (off).
+@end deffn
+
+@deffn {Command} {xtensa smpbreak} [none|breakinout|runstall] | [BreakIn] [BreakOut] [RunStallIn] [DebugModeOut]
+Configures debug signals connection ("break network") for currently selected core.
+@itemize @bullet
+@item @code{none} - Core's "break/stall network" is disconnected. Core is not affected by any debug
+signal from other cores.
+@item @code{breakinout} - Core's "break network" is fully connected (break inputs and outputs are enabled).
+Core will receive debug break signals from other cores and send such signals to them. For example when another core
+is stopped due to breakpoint hit this core will be stopped too and vice versa.
+@item @code{runstall} - Core's "stall network" is fully connected (stall inputs and outputs are enabled).
+This feature is not well implemented and tested yet.
+@item @code{BreakIn} - Core's "break-in" signal is enabled.
+Core will receive debug break signals from other cores. For example when another core is
+stopped due to breakpoint hit this core will be stopped too.
+@item @code{BreakOut} - Core's "break-out" signal is enabled.
+Core will send debug break signal to other cores. For example when this core is
+stopped due to breakpoint hit other cores with enabled break-in signals will be stopped too.
+@item @code{RunStallIn} - Core's "runstall-in" signal is enabled.
+This feature is not well implemented and tested yet.
+@item @code{DebugModeOut} - Core's "debugmode-out" signal is enabled.
+This feature is not well implemented and tested yet.
+@end itemize
+@end deffn
+
+@deffn {Command} {xtensa perfmon_enable} <counter_id> <select> [mask] [kernelcnt] [tracelevel]
+Enable and start performance counter.
+@itemize @bullet
+@item @code{counter_id} - Counter ID (0-1).
+@item @code{select} - Selects performance metric to be counted by the counter,
+e.g. 0 - CPU cycles, 2 - retired instructions.
+@item @code{mask} - Selects input subsets to be counted (counter will
+increment only once even if more than one condition corresponding to a mask bit occurs).
+@item @code{kernelcnt} - 0 - count events with "CINTLEVEL <= tracelevel",
+1 - count events with "CINTLEVEL > tracelevel".
+@item @code{tracelevel} - Compares this value to "CINTLEVEL" when deciding
+whether to count.
+@end itemize
+@end deffn
+
+@deffn {Command} {xtensa perfmon_dump} (counter_id)
+Dump performance counter value. If no argument specified, dumps all counters.
+@end deffn
+
+@deffn {Command} {xtensa tracestart} [pc <pcval>/[<maskbitcount>]] [after <n> [ins|words]]
+Set up and start a HW trace. Optionally set PC address range to trigger tracing stop when reached during program execution.
+This command also allows to specify the amount of data to capture after stop trigger activation.
+@itemize @bullet
+@item @code{pcval} - PC value which will trigger trace data collection stop.
+@item @code{maskbitcount} - PC value mask.
+@item @code{n} - Maximum number of instructions/words to capture after trace stop trigger.
+@end itemize
+@end deffn
+
+@deffn {Command} {xtensa tracestop}
+Stop current trace as started by the tracestart command.
+@end deffn
+
+@deffn {Command} {xtensa tracedump} <outfile>
+Dump trace memory to a file.
+@end deffn
+
@anchor{softwaredebugmessagesandtracing}
@section Software Debug Messages and Tracing
@cindex Linux-ARM DCC support
@item @option{Zephyr}
@end itemize
+At any time, it's possible to drop the selected RTOS using:
+@example
+$_TARGETNAME configure -rtos none
+@end example
+
Before an RTOS can be detected, it must export certain symbols; otherwise, it cannot
be used by OpenOCD. Below is a list of the required symbols for each supported RTOS.
while other cores are free-running or remain halted, depending on the
scheduler-locking mode configured in GDB.
-@section Legacy SMP core switching support
-@quotation Note
-This method is deprecated in favor of the @emph{hwthread} pseudo RTOS.
-@end quotation
-
-For SMP support following GDB serial protocol packet have been defined :
-@itemize @bullet
-@item j - smp status request
-@item J - smp set request
-@end itemize
-
-OpenOCD implements :
-@itemize @bullet
-@item @option{jc} packet for reading core id displayed by
-GDB connection. Reply is @option{XXXXXXXX} (8 hex digits giving core id) or
- @option{E01} for target not smp.
-@item @option{JcXXXXXXXX} (8 hex digits) packet for setting core id displayed at next GDB continue
-(core id -1 is reserved for returning to normal resume mode). Reply @option{E01}
-for target not smp or @option{OK} on success.
-@end itemize
-
-Handling of this packet within GDB can be done :
-@itemize @bullet
-@item by the creation of an internal variable (i.e @option{_core}) by mean
-of function allocate_computed_value allowing following GDB command.
-@example
-set $_core 1
-#Jc01 packet is sent
-print $_core
-#jc packet is sent and result is affected in $
-@end example
-
-@item by the usage of GDB maintenance command as described in following example (2 cpus in SMP with
-core id 0 and 1 @pxref{definecputargetsworkinginsmp,,Define CPU targets working in SMP}).
-
-@example
-# toggle0 : force display of coreid 0
-define toggle0
-maint packet Jc0
-continue
-main packet Jc-1
-end
-# toggle1 : force display of coreid 1
-define toggle1
-maint packet Jc1
-continue
-main packet Jc-1
-end
-@end example
-@end itemize
-
@node Tcl Scripting API
@chapter Tcl Scripting API
@cindex Tcl Scripting API
When the command ``proc'' is parsed (which creates a procedure
function) it gets 3 parameters on the command line. @b{1} the name of
the proc (function), @b{2} the list of parameters, and @b{3} the body
-of the function. Not the choice of words: LIST and BODY. The PROC
+of the function. Note the choice of words: LIST and BODY. The PROC
command stores these items in a table somewhere so it can be found by
``LookupCommand()''
projects / fw / openocd / blobdiff