ARM7TDMI: remove now-needless "struct arm7tdmi"

[fw/openocd] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 81409acce7a559f3fb985b74a0f43a5dd0cb0a95..2767d7874ada4e5efa56efc95100e5590ad2f2de 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -5515,16 +5515,14 @@ Reports whether the capture clock is locked or not.
 @end deffn
 
 
-@section ARMv4 and ARMv5 Architecture
-@cindex ARMv4
-@cindex ARMv5
+@section Generic ARM
+@cindex ARM
 
-These commands are specific to ARM architecture v4 and v5,
-including all ARM7 or ARM9 systems and Intel XScale.
+These commands should be available on all ARM processors.
 They are available in addition to other core-specific
 commands that may be available.
 
-@deffn Command {armv4_5 core_state} [@option{arm}|@option{thumb}]
+@deffn Command {arm core_state} [@option{arm}|@option{thumb}]
 Displays the core_state, optionally changing it to process
 either @option{arm} or @option{thumb} instructions.
 The target may later be resumed in the currently set core_state.
@@ -5532,18 +5530,25 @@ The target may later be resumed in the currently set core_state.
 that is not currently supported in OpenOCD.)
 @end deffn
 
-@deffn Command {armv4_5 disassemble} address [count [@option{thumb}]]
+@deffn Command {arm disassemble} address [count [@option{thumb}]]
 @cindex disassemble
 Disassembles @var{count} instructions starting at @var{address}.
 If @var{count} is not specified, a single instruction is disassembled.
 If @option{thumb} is specified, or the low bit of the address is set,
-Thumb (16-bit) instructions are used;
+Thumb2 (mixed 16/32-bit) instructions are used;
 else ARM (32-bit) instructions are used.
 (Processors may also support the Jazelle state, but
 those instructions are not currently understood by OpenOCD.)
+
+Note that all Thumb instructions are Thumb2 instructions,
+so older processors (without Thumb2 support) will still
+see correct disassembly of Thumb code.
+Also, ThumbEE opcodes are the same as Thumb2,
+with a handful of exceptions.
+ThumbEE disassembly currently has no explicit support.
 @end deffn
 
-@deffn Command {armv4_5 reg}
+@deffn Command {arm reg}
 Display a table of all banked core registers, fetching the current value from every
 core mode if necessary. OpenOCD versions before rev. 60 didn't fetch the current
 register value.
@@ -5943,23 +5948,6 @@ Displays the number of extra tck for mem-ap memory bus access [0-255].
 If @var{value} is defined, first assigns that.
 @end deffn
 
-@subsection ARMv7-A specific commands
-@cindex ARMv7-A
-
-@deffn Command {armv7a disassemble} address [count [@option{thumb}]]
-@cindex disassemble
-Disassembles @var{count} instructions starting at @var{address}.
-If @var{count} is not specified, a single instruction is disassembled.
-If @option{thumb} is specified, or the low bit of the address is set,
-Thumb2 (mixed 16/32-bit) instructions are used;
-else ARM (32-bit) instructions are used.
-With a handful of exceptions, ThumbEE instructions are the same as Thumb2;
-ThumbEE disassembly currently has no explicit support.
-(Processors may also support the Jazelle state, but
-those instructions are not currently understood by OpenOCD.)
-@end deffn
-
-
 @subsection Cortex-M3 specific commands
 @cindex Cortex-M3