JIM-Tcl commands, and (older) the orginal command interpreter.
@item @b{Commands}
-@* At the OpenOCD telnet command line (or via the GDB mon command) one
+@* At the OpenOCD telnet command line (or via the GDB monitor command) one
can type a Tcl for() loop, set variables, etc.
Some of the commands documented in this guide are implemented
as Tcl scripts, from a @file{startup.tcl} file internal to the server.
List the debug adapter drivers that have been built into
the running copy of OpenOCD.
@end deffn
+@deffn Command {interface transports} transport_name+
+Specifies the transports supported by this debug adapter.
+The adapter driver builds-in similar knowledge; use this only
+when external configuration (such as jumpering) changes what
+the hardware can support.
+@end deffn
+
+
@deffn Command {adapter_name}
Returns the name of the debug adapter driver being used.
@deffn {Interface Driver} {ZY1000}
This is the Zylin ZY1000 JTAG debugger.
+@end deffn
@quotation Note
This defines some driver-specific commands,
No arguments: print status.
@end deffn
-@end deffn
+@section Transport Configuration
+As noted earlier, depending on the version of OpenOCD you use,
+and the debug adapter you are using,
+several transports may be available to
+communicate with debug targets (or perhaps to program flash memory).
+@deffn Command {transport list}
+displays the names of the transports supported by this
+version of OpenOCD.
+@end deffn
+
+@deffn Command {transport select} transport_name
+Select which of the supported transports to use in this OpenOCD session.
+The transport must be supported by the debug adapter hardware and by the
+version of OPenOCD you are using (including the adapter's driver).
+No arguments: returns name of session's selected transport.
+@end deffn
+
+@subsection JTAG Transport
+JTAG is the original transport supported by OpenOCD, and most
+of the OpenOCD commands support it.
+JTAG transports expose a chain of one or more Test Access Points (TAPs),
+each of which must be explicitly declared.
+JTAG supports both debugging and boundary scan testing.
+Flash programming support is built on top of debug support.
+@subsection SWD Transport
+SWD (Serial Wire Debug) is an ARM-specific transport which exposes one
+Debug Access Point (DAP, which must be explicitly declared.
+(SWD uses fewer signal wires than JTAG.)
+SWD is debug-oriented, and does not support boundary scan testing.
+Flash programming support is built on top of debug support.
+(Some processors support both JTAG and SWD.)
+@subsection SPI Transport
+The Serial Peripheral Interface (SPI) is a general purpose transport
+which uses four wire signaling. Some processors use it as part of a
+solution for flash programming.
@anchor{JTAG Speed}
@section JTAG Speed
@item @code{arm11} -- this is a generation of ARMv6 cores
@item @code{arm720t} -- this is an ARMv4 core with an MMU
@item @code{arm7tdmi} -- this is an ARMv4 core
-@item @code{arm920t} -- this is an ARMv5 core with an MMU
+@item @code{arm920t} -- this is an ARMv4 core with an MMU
@item @code{arm926ejs} -- this is an ARMv5 core with an MMU
@item @code{arm966e} -- this is an ARMv5 core
@item @code{arm9tdmi} -- this is an ARMv4 core
@deffn Command {flash info} num
Print info about flash bank @var{num}
The @var{num} parameter is a value shown by @command{flash banks}.
-The information includes per-sector protect status, which may be
-incorrect (outdated) unless you first issue a
-@command{flash protect_check num} command.
+This command will first query the hardware, it does not print cached
+and possibly stale information.
@end deffn
@anchor{flash protect}
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
-@deffn Command {flash protect_check} num
-Check protection state of sectors in flash bank @var{num}.
-The @var{num} parameter is a value shown by @command{flash banks}.
-@comment @option{flash erase_sector} using the same syntax.
-This updates the protection information displayed by @option{flash info}.
-(Code execution may have invalidated any state records kept by OpenOCD.)
-@end deffn
-
@anchor{Flash Driver List}
@section Flash Driver List
As noted above, the @command{flash bank} command requires a driver name,
@end deffn
@end deffn
+@deffn {Flash Driver} virtual
+This is a special driver that maps a previously defined bank to another
+address. All bank settings will be copied from the master physical bank.
+
+The @var{virtual} driver defines one mandatory parameters,
+
+@itemize
+@item @var{master_bank} The bank that this virtual address refers to.
+@end itemize
+
+So in the following example addresses 0xbfc00000 and 0x9fc00000 refer to
+the flash bank defined at address 0x1fc00000. Any cmds executed on
+the virtual banks are actually performed on the physical banks.
+@example
+flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
+flash bank vbank0 virtual 0xbfc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+flash bank vbank1 virtual 0x9fc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+@end example
+@end deffn
+
@subsection str9xpec driver
@cindex str9xpec
@section Other NAND commands
@cindex NAND other commands
-@deffn Command {nand check_bad_blocks} [offset length]
+@deffn Command {nand check_bad_blocks} num [offset length]
Checks for manufacturer bad block markers on the specified NAND
device. If no parameters are provided, checks the whole
device; otherwise, starts at the specified @var{offset} and
@xref{Running}.
@end deffn
-@deffn Command fast (@option{enable}|@option{disable})
-Default disabled.
-Set default behaviour of OpenOCD to be "fast and dangerous".
-
-At this writing, this only affects the defaults for two ARM7/ARM9 parameters:
-fast memory access, and DCC downloads. Those parameters may still be
-individually overridden.
-
-The target specific "dangerous" optimisation tweaking options may come and go
-as more robust and user friendly ways are found to ensure maximum throughput
-and robustness with a minimum of configuration.
-
-Typically the "fast enable" is specified first on the command line:
-
-@example
-openocd -c "fast enable" -c "interface dummy" -f target/str710.cfg
-@end example
-@end deffn
-
@deffn Command echo message
Logs a message at "user" priority.
Output @var{message} to stdout.
mini-IC is marked valid, which makes the CPU fetch all exception
handlers from the mini-IC, ignoring the code in RAM.
-OpenOCD currently does not sync the mini-IC entries with the RAM
-contents (which would fail anyway while the target is running), so
-the user must provide appropriate values using the @code{xscale
-vector_table} command.
+To address this situation, OpenOCD provides the @code{xscale
+vector_table} command, which allows the user to explicity write
+individual entries to either the high or low vector table stored in
+the mini-IC.
It is recommended to place a pc-relative indirect branch in the vector
table, and put the branch destination somewhere in memory. Doing so
.long real_fiq_handler
@end example
+Alternatively, you may choose to keep some or all of the mini-IC
+vector table entries synced with those written to memory by your
+system software. The mini-IC can not be modified while the processor
+is executing, but for each vector table entry not previously defined
+using the @code{xscale vector_table} command, OpenOCD will copy the
+value from memory to the mini-IC every time execution resumes from a
+halt. This is done for both high and low vector tables (although the
+table not in use may not be mapped to valid memory, and in this case
+that copy operation will silently fail). This means that you will
+need to briefly halt execution at some strategic point during system
+start-up; e.g., after the software has initialized the vector table,
+but before exceptions are enabled. A breakpoint can be used to
+accomplish this once the appropriate location in the start-up code has
+been identified. A watchpoint over the vector table region is helpful
+in finding the location if you're not sure. Note that the same
+situation exists any time the vector table is modified by the system
+software.
+
The debug handler must be placed somewhere in the address space using
the @code{xscale debug_handler} command. The allowed locations for the
debug handler are either (0x800 - 0x1fef800) or (0xfe000800 -
projects / fw / openocd / blobdiff