@item @b{vdebug}
@* A driver for Cadence virtual Debug Interface to emulated or simulated targets.
It implements a client connecting to the vdebug server, which in turn communicates
-with the emulated or simulated RTL model through a transactor. The current version
-supports only JTAG as a transport, but other virtual transports, like DAP are planned.
+with the emulated or simulated RTL model through a transactor. The driver supports
+JTAG and DAP-level transports.
@item @b{jtag_dpi}
@* A JTAG driver acting as a client for the SystemVerilog Direct Programming
@* A bitbang JTAG driver using Linux legacy sysfs GPIO.
This is deprecated from Linux v5.3; prefer using @b{linuxgpiod}.
+@item @b{esp_usb_jtag}
+@* A JTAG driver to communicate with builtin debug modules of Espressif ESP32-C3 and ESP32-S3 chips using OpenOCD.
+
@end itemize
@node About Jim-Tcl
the hardware can support.
@end deffn
+@anchor{adapter gpio}
+@deffn {Config Command} {adapter gpio [ @
+ @option{tdo} | @option{tdi} | @option{tms} | @option{tck} | @option{trst} | @
+ @option{swdio} | @option{swdio_dir} | @option{swclk} | @option{srst} | @
+ @option{led} @
+ [ @
+ gpio_number | @option{-chip} chip_number | @
+ @option{-active-high} | @option{-active-low} | @
+ @option{-push-pull} | @option{-open-drain} | @option{-open-source} | @
+ @option{-pull-none} | @option{-pull-up} | @option{-pull-down} | @
+ @option{-init-inactive} | @option{-init-active} | @option{-init-input} @
+ ] ]}
+
+Define the GPIO mapping that the adapter will use. The following signals can be
+defined:
+
+@itemize @minus
+@item @option{tdo}, @option{tdi}, @option{tms}, @option{tck}, @option{trst}:
+JTAG transport signals
+@item @option{swdio}, @option{swclk}: SWD transport signals
+@item @option{swdio_dir}: optional swdio buffer control signal
+@item @option{srst}: system reset signal
+@item @option{led}: optional activity led
+
+@end itemize
+Some adapters require that the GPIO chip number is set in addition to the GPIO
+number. The configuration options enable signals to be defined as active-high or
+active-low. The output drive mode can be set to push-pull, open-drain or
+open-source. Most adapters will have to emulate open-drain or open-source drive
+modes by switching between an input and output. Input and output signals can be
+instructed to use a pull-up or pull-down resistor, assuming it is supported by
+the adaptor driver and hardware. The initial state of outputs may also be set,
+"active" state means 1 for active-high outputs and 0 for active-low outputs.
+Bidirectional signals may also be initialized as an input. If the swdio signal
+is buffered the buffer direction can be controlled with the swdio_dir signal;
+the active state means that the buffer should be set as an output with respect
+to the adapter. The command options are cumulative with later commands able to
+override settings defined by earlier ones. The two commands @command{gpio led 7
+-active-high} and @command{gpio led -chip 1 -active-low} sent sequentially are
+equivalent to issuing the single command @command{gpio led 7 -chip 1
+-active-low}. It is not permissible to set the drive mode or initial state for
+signals which are inputs. The drive mode for the srst and trst signals must be
+set with the @command{adapter reset_config} command. It is not permissible to
+set the initial state of swdio_dir as it is derived from the initial state of
+swdio. The command @command{adapter gpio} prints the current configuration for
+all GPIOs while the command @command{adapter gpio gpio_name} prints the current
+configuration for gpio_name. Not all adapters support this generic GPIO mapping,
+some require their own commands to define the GPIOs used. Adapters that support
+the generic mapping may not support all of the listed options.
+@end deffn
@deffn {Command} {adapter name}
Returns the name of the debug adapter driver being used.
@end deffn
+@deffn {Interface Driver} {esp_usb_jtag}
+Espressif JTAG driver to communicate with ESP32-C3, ESP32-S3 chips and ESP USB Bridge board using OpenOCD.
+These chips have built-in JTAG circuitry and can be debugged without any additional hardware.
+Only an USB cable connected to the D+/D- pins is necessary.
+
+@deffn {Config Command} {espusbjtag tdo}
+Returns the current state of the TDO line
+@end deffn
+
+@deffn {Config Command} {espusbjtag setio} setio
+Manually set the status of the output lines with the order of (tdi tms tck trst srst)
+@example
+espusbjtag setio 0 1 0 1 0
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag vid_pid} vid_pid
+Set vendor ID and product ID for the ESP usb jtag driver
+@example
+espusbjtag vid_pid 0x303a 0x1001
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag caps_descriptor} caps_descriptor
+Set the jtag descriptor to read capabilities of ESP usb jtag driver
+@example
+espusbjtag caps_descriptor 0x2000
+@end example
+@end deffn
+
+@deffn {Config Command} {espusbjtag chip_id} chip_id
+Set chip id to transfer to the ESP USB bridge board
+@example
+espusbjtag chip_id 1
+@end example
+@end deffn
+
+@end deffn
@section Transport Configuration
@cindex Transport
Disabled by default
@end deffn
+@deffn {Config Command} {$dap_name nu_npcx_quirks} [@option{enable}]
+Set/get quirks mode for Nuvoton NPCX/NPCD MCU families
+Disabled by default
+@end deffn
@node CPU Configuration
@chapter CPU Configuration
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
-@var{rtos_type} can be one of @option{auto}, @option{eCos},
+@var{rtos_type} can be one of @option{auto}, @option{none}, @option{eCos},
@option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
@option{embKernel}, @option{mqx}, @option{uCOS-III}, @option{nuttx},
@option{RIOT}, @option{Zephyr}
@item @option{Zephyr}
@end itemize
+At any time, it's possible to drop the selected RTOS using:
+@example
+$_TARGETNAME configure -rtos none
+@end example
+
Before an RTOS can be detected, it must export certain symbols; otherwise, it cannot
be used by OpenOCD. Below is a list of the required symbols for each supported RTOS.
projects / fw / openocd / blobdiff