#!/bin/sh
-if [ -x ../ao-tools/ao-load/ao-load ]; then
- AOLOAD=../ao-tools/ao-load/ao-load
-elif [ -x /usr/bin/ao-load ]; then
- AOLOAD=/usr/bin/ao-load
+if [ -x /usr/bin/ao-flash-stm ]; then
+ FLASH_STM=/usr/bin/ao-flash-stm
else
- echo "Can't find ao-load! Aborting."
+ echo "Can't find ao-flash-stm! Aborting."
exit 1
fi
-if [ -x ../ao-tools/ao-rawload/ao-rawload ]; then
- RAWLOAD=../ao-tools/ao-rawload/ao-rawload
-elif [ -x /usr/bin/ao-rawload ]; then
- RAWLOAD=/usr/bin/ao-rawload
+if [ -x /usr/bin/ao-usbload ]; then
+ USBLOAD=/usr/bin/ao-usbload
else
- echo "Can't find ao-rawload! Aborting."
+ echo "Can't find ao-usbload! Aborting."
exit 1
fi
-echo "TeleBT v0.1 Turn-On and Calibration Program"
-echo "Copyright 2011 by Bdale Garbee. Released under GPL v2"
+VERSION=3.0
+REPO=~/altusmetrumllc/Binaries
+
+echo "TeleBT v$VERSION Turn-On and Calibration Program"
+echo "Copyright 2015 by Bdale Garbee. Released under GPL v2"
echo
echo "Expectations:"
-echo "\tTeleBT v0.1 powered from USB"
-echo "\t\twith TeleDonle (on /dev/ttyACM0) cabled to debug header"
-echo "\t\twith coax from SMA to frequency counter"
+echo "\tTeleBT v$VERSION powered from USB"
+echo "\t\twith ST-Link-V2 cabled to debug header"
+echo "\t\twith coax from UHF to frequency counter"
echo
-echo -n "TeleBT serial number: "
+echo -n "TeleBT-$VERSION serial number: "
read SERIAL
-echo $RAWLOAD
+echo $FLASH_STM
+
+$FLASH_STM $REPO/loaders/telebt-v$VERSION*.elf || exit 1
-$RAWLOAD -D 100 -r ao_led_blink.ihx
-echo "LEDs should be blinking"
sleep 5
-$RAWLOAD -D 100 -r ao_radio_xmit.ihx
-echo -n "Generating RF carrier. Please enter measured frequency: "
-read FREQ
+$USBLOAD --serial=$SERIAL $REPO/telebt-v$VERSION*.elf || exit 1
+
+sleep 5
+
+dev=`ao-list | awk '/TeleBT-v'"$VERSION"'/ { print $3; exit(0); }'`
+
+case "$dev" in
+/dev/tty*)
+ echo "TeleBT found on $dev"
+ ;;
+*)
+ echo 'No TeleBT-v'"$VERSION"' found'
+ exit 1
+ ;;
+esac
-CAL_VALUE=`nickle -e "floor(434.55 / $FREQ * 1186611 + 0.5)"`
+echo 'E 0' > $dev
+
+SERIAL=$SERIAL ./cal-freq $dev
+
+echo 'E 1' > $dev
+
+echo -n "checking BlueTooth functionality... "
+btdev=`hcitool scan | awk -F \- '/TeleBT/ { print $2 }'`
+if [ "$btdev" = "$SERIAL" ]; then
+ echo "working!"
+else
+ echo "device not found"
+ exit 1
+fi
-echo "Programming flash with cal value " $CAL_VALUE
-$AOLOAD -D 100 --cal $CAL_VALUE /usr/share/altos/telebt-v0.1*.ihx $SERIAL
+echo "TeleBT-v$VERSION $SERIAL is ready to ship"
-echo "Serial number "$SERIAL" programmed with RF cal value "$CAL_VALUE
-echo "Unplug and replug USB, cu to the board, confirm freq and record power"
+exit $?