-This file includes highlights of the changes made in the
-OpenOCD 0.4.0 source archive release. See the repository
-history for details about what changed, including bugfixes
-and other issues not mentioned here.
+This file includes highlights of the changes made in the OpenOCD
+source archive release.
JTAG Layer:
- Support KT-Link JTAG adapter.
- Support USB-JTAG, Altera USB-Blaster and compatibles.
+ * add debug level 4 for verbose I/O debug
+ * bitbang, add read buffer to improve performance
+ * Cadence SystemVerilog Direct Programming Interface (DPI) adapter driver
+ * CMSIS-DAP v2 (USB bulk based) adapter driver
+ * Cypress KitProg adapter driver
+ * FTDI FT232R sync bitbang adapter driver
+ * Linux GPIOD bitbang adapter driver through libgpiod
+ * Mellanox rshim USB or PCIe adapter driver
+ * Nuvoton Nu-Link and Nu-Link2 adapter drivers
+ * NXP IMX GPIO mmap based adapter driver
+ * ST-Link consolidate all versions in single config
+ * ST-Link read properly old USB serial numbers
+ * STLink/V3 support (for ST devices only !)
+ * STM8 SWIM transport
+ * TI XDS110 adapter driver
+ * Xilinx XVC/PCIe adapter driver
Boundary Scan:
+
Target Layer:
- General
- - new "reset-assert" event, for systems without SRST
- ARM
- - renamed "armv4_5" command prefix as "arm"
- - recognize TrustZone "Secure Monitor" mode
- - "arm regs" command output changed
- - register names use "sp" not "r13"
- - add top-level "mcr" and "mrc" commands, replacing
- various core-specific operations
- - basic semihosting support
- ARM11
- - Preliminary ETM and ETB hookup
- - accelerated "flash erase_check"
- - accelerated GDB memory checksum
- - support "arm regs" command
- - can access all core modes and registers
- - watchpoint support
- Cortex-A8
- - support "arm regs" command
- - can access all core modes and registers
- - supports "reset-assert" event (used on OMAP3530)
- - watchpoint support
- Cortex-M3
- - Exposed DWT registers like cycle counter
- ETM, ETB
- - "trigger_percent" command moved ETM --> ETB
- - "etm trigger_debug" command added
- Freescale DSP563xx cores (partial support)
+ * 64 bit address support
+ * ARCv2 target support
+ * ARM Cortex-A hypervisor mode support
+ * ARM Cortex-M fast PC sampling support for profiling
+ * ARM generic CTI support
+ * ARM generic mem-ap target support
+ * ARMv7-A MMU tools
+ * ARMv7m traces add TCP stream server
+ * ARMv8 AARCH64 target support and semihosting support
+ * ARMv8 AARCH64 disassembler support through capstone library
+ * ARMv8-M target support
+ * EnSilica eSi-RISC target support, including instruction tracing
+ eSi-Trace support
+ * MIPS64 target support
+ * Motorola SREC S6 record image file support
+ * RISC-V target support
+ * SEGGER Real Time Transfer (RTT) initial support (for single target,
+ Cortex-M only)
+ * ST STM8 target support
+ * Various MIPS32 target improvements
Flash Layer:
- 'flash bank' and 'nand device' take <bank_name> as first argument.
- With this, flash/NAND commands allow referencing banks by name:
- - <bank_name>: reference the bank with its defined name
- - <driver_name>[.N]: reference the driver's Nth bank
- New 'nand verify' command to check bank against an image file.
- The "flash erase_address" command now rejects partial sectors;
- previously it would silently erase extra data.
- New at91sam9 NAND controller driver.
+ * Atheros (ath79) SPI interface support
+ * Atmel atmega128rfa1 support
+ * Atmel SAM D21, D51, DA1, E51, E53, E54, G55, R30 support
+ * Atmel SAMC2?N* support
+ * Cypress PSoC5LP, PSoC6 support
+ * EnSilica eSi-RISC support
+ * Foshan Synwit Tech SWM050 support
+ * Maxim Integrated MAX32XXX support
+ * Nordic Semiconductor nRF51822, nRF52810, nRF52832 support
+ * NXP Kinetis K27, K28, KE1x, KEAx, KL28, KL8x, KV5x, KWx support
+ * Renesas RPC HF support
+ * SH QSPI support
+ * SiFive Freedom E support
+ * Silicon Labs EFR-family, EZR32HG support
+ * ST BlueNRG support
+ * ST STM32 QUAD/OCTO-SPI interface support for Flash, FRAM and EEPROM
+ * ST STM32F72x, STM32F4x3, STM32H7xx support
+ * ST STM32G0xx, STM32G4xx, STM32L4x, STM32WB, STM32WL support
+ * ST STM32L5x support (non secure mode)
+ * TI CC13xx, CC26xx, CC32xx support
+ * TI MSP432 support
+ * Winner Micro w600 support
+ * Xilinx XCF platform support
+ * Various discrete SPI NOR flashes support
Board, Target, and Interface Configuration Scripts:
- ARM9
- - ETM and ETB hookup for iMX2* targets
- Add $HOME/.openocd to the search path.
+ * 8devices LIMA board config
+ * Achilles Instant-Development Kit Arria 10 board config
+ * Amazon Kindle 2 and DX board config
+ * Analog Devices ADSP-SC58x, ADSP-SC584-EZBRD board config
+ * Andes Technology ADP-XC7KFF676 board config
+ * Andes Technology Corvette-F1 board config
+ * ARM Musca A board config
+ * Arty Spartan 7 FPGA board config
+ * Atmel SAMD10 Xplained mini board config
+ * Atmel SAMD11 Xplained Pro board config
+ * Atmel SAM G55 Xplained Pro board config
+ * AVNET UltraZED EG StarterKit board config
+ * Blue Pill STM32F103C8 board config
+ * DP Busblaster v4.1a board config
+ * DPTechnics DPT-Board-v1 board config
+ * Emcraft imx8 SOM BSB board config
+ * Globalscale ESPRESSObin board config
+ * Kasli board config
+ * Kintex Ultrascale XCKU040 board config
+ * Knovative KC-100 board config
+ * LeMaker HiKey board config
+ * Microchip (Atmel) SAME54 Xplained Pro board config
+ * Microchip (Atmel) SAML11 Xplained Pro board config
+ * Nordic module NRF52 board config
+ * Numato Lab Mimas A7 board config
+ * NXP Freedom FRDM-LS1012A board config
+ * NXP IMX7SABRE board config
+ * NXP IMX8MP-EVK board config
+ * NXP MC-IMX8M-EVK board config
+ * QuickLogic QuickFeather board config
+ * Renesas R-Car E2, H2, M2 board config
+ * Renesas R-Car Salvator-X(S) board config
+ * Renesas RZ/A1H GR-Peach board config
+ * Rigado BMD-300 board config
+ * Sayma AMC board config
+ * Sifive e31arty, e51arty, hifive1 board config
+ * ST B-L475E-IOT01A board config
+ * ST BlueNRG idb007v1, idb008v1, idb011v1 board config
+ * ST STM32F412g discovery board config
+ * ST STM32F413h discovery board config
+ * ST STM32F469i discovery board config
+ * ST STM32F7 Nucleo board config
+ * ST STM32F723e discovery board config
+ * ST STM32F746g discovery board config
+ * ST STM32F769i discovery board config
+ * ST STM32H735g discovery board config
+ * ST STM32H743zi Nucleo board config
+ * ST STM32H745i discovery board config
+ * ST STM32H747i discovery board config
+ * ST STM32H750b discovery board config
+ * ST STM32H7b3i discovery board config
+ * ST STM32H7x_dual_qspi board config
+ * ST STM32H7x3i Eval boards config
+ * ST STM32L073 Nucleo board config
+ * ST STM32L476g discovery board config
+ * ST STM32L496g discovery board config
+ * ST STM32L4p5g discovery board config
+ * ST STM32L4r9i discovery board config
+ * ST STM32L5 Nucleo board config
+ * ST STM32MP15x DK2 board config
+ * ST STM32WB Nucleo board config
+ * ST STM8L152R8 Nucleo board config
+ * Synopsys DesignWare ARC EM board config
+ * Synopsys DesignWare ARC HSDK board config
+ * TI BeagleBone family boards config
+ * TI CC13xx, CC26xx, CC32xx LaunchPad board config
+ * TI MSP432 LaunchPad board config
+ * Tocoding Poplar board config
+ * TP-Link WDR4300 board config
+ * Allwinner V3s target config
+ * Andes Technology NDS V5 target config
+ * Atmel atmega128rfa1 target config
+ * ARM corelink SSE-200 target config
+ * Atheros_ar9344 target config
+ * Cypress PSoC5LP, PSoC6 target config
+ * EnSilica eSi-RISC target config
+ * Foshan Synwit Tech SWM050 target config
+ * GigaDevice GD32VF103 target config
+ * Hisilicon Hi3798 target config
+ * Hisilicon Hi6220 target config
+ * Infineon TLE987x target config
+ * Marvell Armada 3700 target config
+ * Maxim Integrated MAX32XXX target config
+ * Mellanox BlueField target config
+ * Microchip (Atmel) SAME5x, SAML1x target config
+ * NXP IMX6SX, IMX6UL, IMX7, IMX7ULP, IMX8 target config
+ * NXP Kinetis KE1xZ, KE1xF target config
+ * NXP LPC84x, LPC8Nxx, LS1012A, NHS31xx target config
+ * Qualcomm QCA4531 target config
+ * QuickLogic EOS S3 target config
+ * Renesas R-Car E2, H2, M2 target config
+ * Renesas R-Car Gen3 target config
+ * Renesas RZ/A1H target config
+ * Rockchip RK3308 target config
+ * ST BlueNRG target config
+ * ST STM32G0, STM32G4, STM32H7, STM32L0, STM32L5 target config
+ * ST STM32MP15x target config
+ * ST STM32WBx, STM32WLEx target config
+ * ST STM8L152, S003, S103, S105 target config
+ * Synopsys DesignWare ARC EM target config
+ * Synopsys DesignWare ARC HS Development Kit SoC target config
+ * TI CC13xx, CC26xx, CC32xx target config
+ * TI TNETC4401 target config
+ * Xilinx UltraScale+ target config
+ * Altera 5M570Z (MAXV family) CPLD config
+ * Xilinx Ultrascale, XCF CPLD config
+ * Intel (Altera) Arria10 FPGA config
+ * Cadence SystemVerilog Direct Programming Interface (DPI) interface config
+ * Cypress KitProg interface config
+ * Digilent SMT2 NC interface config
+ * DLN-2 example of Linux GPIOD interface config
+ * FTDI C232HM interface config
+ * HIE JTAG Debugger interface config
+ * In-Circuit's ICprog interface config
+ * isodebug isolated JTAG/SWD+UART interface config
+ * Mellanox rshim USB or PCIe interface config
+ * Nuvoton Nu-Link interface config
+ * NXP IMX GPIO mmap based interface config
+ * Steppenprobe open hardware interface config
+ * TI XDS110 interface config
+
+Server Layer:
+ * 64 bit address support
+ * default bind to IPv4 localhost
+ * gdb: allow multiple connections
+ * gdb: architecture element support
+ * gdb: vCont, vRun support
+ * telnet: handle Ctrl+A, Ctrl+E and Ctrl+K
-Core Jim/TCL Scripting:
- New 'usage' command to provide terse command help.
- Improved command 'help' command output (sorted and indented).
- Improved command handling:
- - Most boolean settings now accept any of the following:
- on/off, enable/disable, true/false, yes/no, 1/0
- - More error checking and reporting.
+RTOS:
+ * Chromium-EC rtos support
+ * hwthread pseudo rtos support
+ * NuttX rtos support
+ * RIOT rtos support
Documentation:
- New built-in command development documentation and primer.
+ * Improve STM32 flash driver
+ * Various typo fix and improvements
Build and Release:
- Use --enable-doxygen-pdf to build PDF developer documentation.
- Consider upgrading to libftdi 0.17 if you use that library; it
- includes bugfixes which improve FT2232H support.
+ * Add libutil to support jimtcl version 0.80
+ * Clang warning fixes
+ * GitHub workflow for Win32 snapshot binaries
+ * Handle Tcl return values consistently
+ * Mitigation for CVE-2018-5704: Prevent some forms of Cross
+ Protocol Scripting attacks
+ * Support for libftdi 1.5
+ * Travis-CI basic support
+ * Update libjaylink to version 0.2.0
+ * Update jimtcl to version 0.79
+ * Use external (optional) library capstone for ARM and AARCH64 disassembly
+
+
+This release also contains a number of other important functional and
+cosmetic bugfixes. For more details about what has changed since the
+last release, see the git repository history:
+
+http://sourceforge.net/p/openocd/code/ci/v0.11.0/log/?path=
-For more details about what has changed since the last release,
-see the git repository history. With gitweb, you can browse that
-in various levels of detail.
For older NEWS, see the NEWS files associated with each release
(i.e. NEWS-<version>).
For more information about contributing test reports, bug fixes, or new
features and device support, please read the new Developer Manual (or
-the BUGS and PATCHES files in the source archive).
+the BUGS and PATCHES.txt files in the source archive).
projects / fw / openocd / blobdiff