projects
/
fw
/
openocd
/ blobdiff
commit
grep
author
committer
pickaxe
?
search:
re
summary
|
shortlog
|
log
|
commit
|
commitdiff
|
tree
raw
|
inline
| side by side
tcl/board: add ESP32 config for ESP USB Bridge board
[fw/openocd]
/
tcl
/
target
/
stm32f7x.cfg
diff --git
a/tcl/target/stm32f7x.cfg
b/tcl/target/stm32f7x.cfg
index db1794c195fdc5037f697d30df961339e4b6f17f..3782b9a9cce5dcc4fb778b5cc52a9bccd7291037 100644
(file)
--- a/
tcl/target/stm32f7x.cfg
+++ b/
tcl/target/stm32f7x.cfg
@@
-1,3
+1,5
@@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
# script for stm32f7x family
#
# script for stm32f7x family
#
@@
-12,7
+14,7
@@
if { [info exists CHIPNAME] } {
set _CHIPNAME stm32f7x
}
set _CHIPNAME stm32f7x
}
-
set _ENDIAN little
+set _ENDIAN little
# Work-area is a space in RAM used for flash programming
# By default use 128kB
# Work-area is a space in RAM used for flash programming
# By default use 128kB
@@
-64,6
+66,12
@@
flash bank $_CHIPNAME.otp stm32f2x 0x1ff0f000 0 0 0 $_TARGETNAME
# the Flash via ITCM alias as virtual
flash bank $_CHIPNAME.itcm-flash.alias virtual 0x00200000 0 0 0 $_TARGETNAME $_FLASHNAME
# the Flash via ITCM alias as virtual
flash bank $_CHIPNAME.itcm-flash.alias virtual 0x00200000 0 0 0 $_TARGETNAME $_FLASHNAME
+if { [info exists QUADSPI] && $QUADSPI } {
+ set a [llength [flash list]]
+ set _QSPINAME $_CHIPNAME.qspi
+ flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+}
+
# adapter speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
adapter speed 2000
# adapter speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
adapter speed 2000
@@
-76,7
+84,7
@@
if {[using_jtag]} {
#
# This target is compatible with connect_assert_srst, which may be set in a
# board file.
#
# This target is compatible with connect_assert_srst, which may be set in a
# board file.
-reset_config srst_
only srst_
nogate
+reset_config srst_nogate
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
@@
-101,13
+109,20
@@
$_TARGETNAME configure -event examine-end {
mmw 0xE0042008 0x00001800 0
}
mmw 0xE0042008 0x00001800 0
}
-$_TARGETNAME configure -event trace-config {
+tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
+
+lappend _telnet_autocomplete_skip _proc_pre_enable_$_CHIPNAME.tpiu
+proc _proc_pre_enable_$_CHIPNAME.tpiu {_targetname} {
+ targets $_targetname
+
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
# change this value accordingly to configure trace pins
# assignment
mmw 0xE0042004 0x00000020 0
}
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
# change this value accordingly to configure trace pins
# assignment
mmw 0xE0042004 0x00000020 0
}
+$_CHIPNAME.tpiu configure -event pre-enable "_proc_pre_enable_$_CHIPNAME.tpiu $_TARGETNAME"
+
$_TARGETNAME configure -event reset-init {
# If the HSE was previously enabled and the external clock source
# disappeared, RCC_CR.HSERDY can get stuck at 1 and the PLL cannot be
$_TARGETNAME configure -event reset-init {
# If the HSE was previously enabled and the external clock source
# disappeared, RCC_CR.HSERDY can get stuck at 1 and the PLL cannot be
@@
-170,4
+185,3
@@
$_TARGETNAME configure -event reset-start {
# Reduce speed since CPU speed will slow down to 16MHz with the reset
adapter speed 2000
}
# Reduce speed since CPU speed will slow down to 16MHz with the reset
adapter speed 2000
}
-