-.IR label .
-.TP
-.B taper
-Perform the
-.B taper
-scan algorithm.
-Load the next tape in the configuration's tape sequence,
-or a fresh tape with a suitable label.
-.TP
-.B device
-Display the name of the current tape device on
-.IR stdout .
-.TP
-.B current
-Display the current slot.
-.TP
-.B update
-Update the changer label database, if it has one,
-to match the tapes now available.
-.TP
-.CO slot slot
-Eject any tape in the drive and put it away,
-then load the tape from slot
-.I slot
-and reset
-.IR current .
-.TP
-.B slot current
-Eject any tape in the drive and put it away,
-then load the tape from the current slot.
-.TP
-.B slot prev
-Eject any tape in the drive and put it away,
-then load the tape from the previous slot and reset
-.IR current .
-.TP
-.B slot next
-Eject any tape in the drive and put it away,
-then load the tape from the next slot and reset
-.IR current .
-.TP
-.B slot first
-Eject any tape in the drive and put it away,
-then load the tape from the first slot and reset
-.IR current .
-.TP
-.B slot last
-Eject any tape in the drive and put it away,
-then load the tape from the last slot and reset
-.IR current .
-.TP
-.B slot advance
-Eject any tape in the drive and put it away.
-Advance
-.I current
-to the next tape, but do not load it.
-.IP
-This is useful with non-gravity stackers to unload the last tape used
-and set up Amanda for the next run.
-If you just use
-.BR eject ,
-the current tape will be mounted again in the next run,
-where it will be rejected as being still in use,
-ejected and the next tape requested.
-Using
-.B slot next
-followed by
-.B eject
-does an unnecessary mount.
-.LP
-Note: most changers optimize the
-.B slot
-commands to not eject the loaded tape if it is the one being requested.
-.SH AUTHOR
-James da Silva <jds@cs.umd.edu>
-.br
-University of Maryland, College Park
+[label], also setting the current slot\&.
+.RE
+.PP
+\fBslot\fR \fIslot\fR
+.RS 4
+Load the volume in the given slot, also setting the current slot\&. The slot names
+\fBcurrent\fR,
+\fBnext\fR,
+\fBfirst\fR, and
+\fBlast\fR
+have special meaning\&.
+.RE
+.PP
+\fBcurrent\fR
+.RS 4
+Shorthand for
+\fBslot\fR
+current\&.
+.RE
+.PP
+\fBinventory\fR
+.RS 4
+Show the contents of all slots, based on the changer\'s cached metadata\&. This is a quick operation as it does not load or unload any volumes, but is not supported by all changers\&.
+.RE
+.PP
+\fBshow\fR
+.RS 4
+Show the contents of all slots by loading each slot and reading its label\&. This can be very slow\&.
+.RE
+.PP
+\fBreset\fR
+.RS 4
+Reset the changer to a known state\&. This subcommand is intended to clear any unknown and potentially incorrect state the changer may have stored\&.
+.RE
+.PP
+\fBeject\fR [\fIdrive\fR]
+.RS 4
+Eject the tape currently in the drive\&. This only applies to some changers\&. Specify a drive (by drive number) if more than one drive is available\&.
+.RE
+.PP
+\fBclean\fR [\fIdrive\fR]
+.RS 4
+If a cleaning tape is defined for the changer, used it to clean the specified drive\&. The
+[drive]
+is optional if the changer only has one drive\&.
+.RE
+.PP
+\fBtaper\fR
+.RS 4
+Run the taperscan algorithm (see
+\fBamanda-taperscan\fR(7)), displaying information about the progress of the scan\&.
+.RE
+.PP
+\fBupdate\fR [what]
+.RS 4
+Update changer state\&. Consult
+\fBamanda-changers\fR(7)
+for changer\-specific details on the format of
+what\&.
+.RE
+.PP
+\fB\-o \fR\fB\fIconfigoption\fR\fR
+.RS 4
+See the "CONFIGURATION OVERRIDE" section in
+\fBamanda\fR(8)\&.
+.RE