-# amanda.conf - sample Amanda configuration file. See amanda.conf(5) for
-# details
-
-org "DailySet1" # your organization name for reports
-mailto "martinea" # space separated list of operators at your site
-dumpuser "martinea" # the user to run dumps under
-
-inparallel 4 # maximum dumpers that will run in parallel (max 63)
- # this maximum can be increased at compile-time,
- # modifying MAX_DUMPERS in server-src/driverio.h
-dumporder "sssS" # specify the priority order of each dumper
- # s -> smallest size
- # S -> biggest size
- # t -> smallest time
- # T -> biggest time
- # b -> smallest bandwitdh
- # B -> biggest bandwitdh
- # try "BTBTBTBTBTBT" if you are not holding
- # disk constrained
-
-taperalgo first # The algorithm used to choose which dump image to send
- # to the taper.
- # Possible values:
- # [first|firstfit|largest|largestfit|smallest|last]
- # Default: first.
- # first First in - first out.
- # firstfit The first dump image that will fit
- # on the current tape.
- # largest The largest dump image.
- # largestfit The largest dump image that will fit
- # on the current tape.
- # smallest The smallest dump image.
- # last Last in - first out.
-
-displayunit "k" # Possible values: "k|m|g|t"
- # Default: k.
- # The unit used to print many numbers.
- # k=kilo, m=mega, g=giga, t=tera
-
-netusage 8000 Kbps # maximum net bandwidth for Amanda, in KB per sec
-
-dumpcycle 4 weeks # the number of days in the normal dump cycle
-runspercycle 20 # the number of amdump runs in dumpcycle days
- # (4 weeks * 5 amdump runs per week -- just weekdays)
-tapecycle 25 tapes # the number of tapes in rotation
- # 4 weeks (dumpcycle) times 5 tapes per week (just
- # the weekdays) plus a few to handle errors that
- # need amflush and so we do not overwrite the full
- # backups performed at the beginning of the previous
- # cycle
-
-bumpsize 20 Mb # minimum savings (threshold) to bump level 1 -> 2
-bumppercent 20 # minimum savings (threshold) to bump level 1 -> 2
-bumpdays 1 # minimum days at each level
-bumpmult 4 # threshold = bumpsize * bumpmult^(level-1)
-
-etimeout 300 # number of seconds per filesystem for estimates.
-dtimeout 1800 # number of idle seconds before a dump is aborted.
-ctimeout 30 # maximum number of seconds that amcheck waits
- # for each client host
-
-device_output_buffer_size 1280k
- # amount of buffer space to use when writing to devices
-
-# By default, Amanda can only track at most one run per calendar day. When
-# the usetimestamps option is enabled, however, Amanda can track as many
-# runs as you care to make.
-# WARNING: This option is not backward-compatible. Do not enable it if you
-# intend to downgrade your server installation to Amanda community
-# edition 2.5
-usetimestamps yes
-
-# flush-threshold-dumped, flush-threshold-scheduled, taperflush, and autoflush
-# are used to control tape utilization. See the amanda.conf (5) manpage for
-# details on how they work. Taping will not start until all criteria are
-# satisfied. Here are some examples:
-#
-# You want to fill tapes completely even in the case of failed dumps, and
-# don't care if some dumps are left on the holding disk after a run:
-# flush-threshold-dumped 100 # (or more)
-# flush-threshold-scheduled 100 # (or more)
-# taperflush 100
-# autoflush yes
-#
-# You want to improve tape performance by waiting for a complete tape of data
-# before writing anything. However, all dumps will be flushed; none will
-# be left on the holding disk.
-# flush-threshold-dumped 100 # (or more)
-# flush-threshold-scheduled 100 # (or more)
-# taperflush 0
-#
-# You don't want to use a new tape for every run, but want to start writing
-# to tape as soon as possible:
-# flush-threshold-dumped 0 # (or more)
-# flush-threshold-scheduled 100 # (or more)
-# taperflush 100
-# autoflush yes
-# maxdumpsize 100k # amount of data to dump each run; see above.
-#
-# You want to keep the most recent dumps on holding disk, for faster recovery.
-# Older dumps will be rotated to tape during each run.
-# flush-threshold-dumped 300 # (or more)
-# flush-threshold-scheduled 300 # (or more)
-# taperflush 300
-# autoflush yes
-#
-# Defaults:
-# (no restrictions; flush to tape immediately; don't flush old dumps.)
-flush-threshold-dumped 0
-flush-threshold-scheduled 0
-taperflush 0
-autoflush no
-
-# Specify tape device and/or tape changer. If you don't have a tape
-# changer, and you don't want to use more than one tape per run of
-# amdump, just comment out the definition of tpchanger.
-
-# Some tape changers require tapedev to be defined; others will use
-# their own tape device selection mechanism. Some use a separate tape
-# changer device (changerdev), others will simply ignore this
-# parameter. Some rely on a configuration file (changerfile) to
-# obtain more information about tape devices, number of slots, etc;
-# others just need to store some data in files, whose names will start
-# with changerfile.
-
-# At most one changerfile entry must be defined; select the most
-# appropriate one for your configuration. If you select man-changer,
-# keep the first one; if you decide not to use a tape changer, you may
-# comment them all out.
-
-runtapes 1 # number of tapes to be used in a single run of amdump
-tpchanger "chg-manual" # the tape-changer glue script
-tapedev "tape:/dev/YOUR-TAPE-DEVICE-HERE" # the no-rewind tape device to be used
-
-#changerfile "/etc/amanda/DailySet1/changer"
-#changerfile "/etc/amanda/DailySet1/changer-status"
-changerfile "/etc/amanda/DailySet1/changer.conf"
-changerdev "/dev/null"
-
-# If you want Amanda to automatically label any non-Amanda tapes it
-# encounters, uncomment the line below. Note that this will ERASE any
-# non-Amanda tapes you may have, and may also ERASE any near-failing tapes.
-# Use with caution.
-## label_new_tapes "DailySet1-%%%"
-
-maxdumpsize -1 # Maximum number of bytes the planner will schedule
- # for a run (default: runtapes * tape_length).
-tapetype HP-DAT # what kind of tape it is (see tapetypes below)
-labelstr "^DailySet1-[0-9][0-9]*$" # label constraint regex: all tapes must match
-
-amrecover_do_fsf yes # amrecover will call amrestore with the
- # -f flag for faster positioning of the tape.
-amrecover_check_label yes # amrecover will call amrestore with the
- # -l flag to check the label.
-amrecover_changer "changer" # amrecover will use the changer if you restore
- # from this device. It could be a string like 'changer' and amrecover will use your
- # changer if you set your tape to 'changer' with 'setdevice changer' or via
- # 'tapedev "changer"' in amanda-client.conf
-
-# Specify holding disks. These are used as a temporary staging area for
-# dumps before they are written to tape and are recommended for most sites.
-# The advantages include: tape drive is more likely to operate in streaming
-# mode (which reduces tape and drive wear, reduces total dump time); multiple
-# dumps can be done in parallel (which can dramatically reduce total dump time.
-# The main disadvantage is that dumps on the holding disk need to be flushed
-# (with amflush) to tape after an operating system crash or a tape failure.
-# If no holding disks are specified then all dumps will be written directly
-# to tape. If a dump is too big to fit on the holding disk than it will be
-# written directly to tape. If more than one holding disk is specified then
-# they will all be used based on activity and available space.
-
-holdingdisk hd1 {
- comment "main holding disk"
- directory "/dumps/amanda" # where the holding disk is
- use -100 Mb # how much space can we use on it
- # a non-positive value means:
- # use all space but that value
- chunksize 1Gb # size of chunk if you want big dump to be
- # dumped on multiple files on holding disks
- # N Kb/Mb/Gb split images in chunks of size N
- # The maximum value should be
- # (MAX_FILE_SIZE - 1Mb)
- # 0 same as INT_MAX bytes
- }
-#holdingdisk hd2 {
-# directory "/dumps2/amanda"
-# use 1000 Mb
-# }
-#holdingdisk hd3 {
-# directory "/mnt/disk4"
-# use 1000 Mb
-# }
-
-
-# If amanda cannot find a tape on which to store backups, it will run
-# as many backups as it can to the holding disks. In order to save
-# space for unattended backups, by default, amanda will only perform
-# incremental backups in this case, i.e., it will reserve 100% of the
-# holding disk space for the so-called degraded mode backups.
-# However, if you specify a different value for the `reserve'
-# parameter, amanda will not degrade backups if they will fit in the
-# non-reserved portion of the holding disk.
-
-# reserve 30 # percent
-# This means save at least 30% of the holding disk space for degraded
-# mode backups.
-
-# The format for a ColumnSpec is a ',' seperated list of triples.
-# Each triple consists of
-# + the name of the column (as in ColumnNameStrings)
-# + prefix before the column
-# + the width of the column, if set to -1 it will be recalculated
-# to the maximum length of a line to print.
-# Example:
-# "Disk=1:17,HostName=1:10,OutKB=1:7"
-# or
-# "Disk=1:-1,HostName=1:10,OutKB=1:7"
-#
-# You need only specify those colums that should be changed from
-# the default. If nothing is specified in the configfile, the
-# above compiled in values will be in effect, resulting in an
-# output as it was all the time.
-# The names of the colums are:
-# HostName, Disk, Level, OrigKB, OutKB, Compress, DumpTime, DumpRate,
-# TapeTime and TapeRate.
-# ElB, 1999-02-24.
-# columnspec "Disk=1:18,HostName=0:10,OutKB=1:7"
-
-
-# Amanda needs a few Mb of diskspace for the log and debug files,
-# as well as a database. This stuff can grow large, so the conf directory
-# isn't usually appropriate. Some sites use /usr/local/var and some /usr/adm.
-# Create an amanda directory under there. You need a separate infofile and
-# logdir for each configuration, so create subdirectories for each conf and
-# put the files there. Specify the locations below.
-
-# Note that, although the keyword below is infofile, it is only so for
-# historic reasons, since now it is supposed to be a directory (unless
-# you have selected some database format other than the `text' default)
-infofile "/etc/amanda/DailySet1/curinfo" # database DIRECTORY
-logdir "/etc/amanda/DailySet1" # log directory
-indexdir "/etc/amanda/DailySet1/index" # index directory
-#tapelist "/etc/amanda/DailySet1/tapelist" # list of used tapes
-# tapelist is stored, by default, in the directory that contains amanda.conf
-
-# tapetypes
-
-# Define the type of tape you use here, and use it in "tapetype"
-# above. Some typical types of tapes are included here. The tapetype
-# tells amanda how many MB will fit on the tape, how big the filemarks
-# are, and how fast the tape device is.
-
-# A filemark is the amount of wasted space every time a tape section
-# ends.
-
-# For completeness Amanda should calculate the inter-record gaps too,
-# but it doesn't. For EXABYTE and DAT tapes this is ok. Anyone using
-# 9 tracks for amanda and need IRG calculations? Drop me a note if
-# so.
-
-# If you want amanda to print postscript paper tape labels
-# add a line after the comment in the tapetype of the form
-# lbl-templ "/path/to/postscript/template/label.ps"
-
-# if you want the label to go to a printer other than the default
-# for your system, you can also add a line above for a different
-# printer. (i usually add that line after the dumpuser specification)
-
-# dumpuser "operator" # the user to run dumps under
-# printer "mypostscript" # printer to print paper label on
-
-# here is an example of my definition for an EXB-8500
-
-# define tapetype EXB-8500 {
-# ...
-# lbl-templ "/etc/amanda/config/lbl.exabyte.ps"
-# }
-
-
-define tapetype QIC-60 {
- comment "Archive Viper"
- length 60 mbytes
- filemark 100 kbytes # don't know a better value
- speed 100 kbytes # dito
-}
-
-define tapetype DEC-DLT2000 {
- comment "DEC Differential Digital Linear Tape 2000"
- length 15000 mbytes
- filemark 8 kbytes
- speed 1250 kbytes
-}
-
-# goluboff@butch.Colorado.EDU
-# in amanda-users (Thu Dec 26 01:55:38 MEZ 1996)
-define tapetype DLT {
- comment "DLT tape drives"
- length 20000 mbytes # 20 Gig tapes
- filemark 2000 kbytes # I don't know what this means
- speed 1536 kbytes # 1.5 Mb/s
-}
-
-define tapetype SURESTORE-1200E {
- comment "HP AutoLoader"
- length 3900 mbytes
- filemark 100 kbytes
- speed 500 kbytes
-}
-
-define tapetype EXB-8500 {
- comment "Exabyte EXB-8500 drive on decent machine"
- length 4200 mbytes
- filemark 48 kbytes
- speed 474 kbytes
-}
-
-define tapetype EXB-8200 {
- comment "Exabyte EXB-8200 drive on decent machine"
- length 2200 mbytes
- filemark 2130 kbytes
- speed 240 kbytes
-}
-
-define tapetype HP-DAT {
- comment "DAT tape drives"
- # data provided by Rob Browning <rlb@cs.utexas.edu>
- length 1930 mbytes
- filemark 111 kbytes
- speed 468 kbytes
-}
-
-define tapetype DAT {
- comment "DAT tape drives"
- length 1000 mbytes # these numbers are not accurate
- filemark 100 kbytes # but you get the idea
- speed 100 kbytes
-}
-
-define tapetype MIMSY-MEGATAPE {
- comment "Megatape (Exabyte based) drive through Emulex on Vax 8600"
- length 2200 mbytes
- filemark 2130 kbytes
- speed 170 kbytes # limited by the Emulex bus interface, ugh
-}
-
-define tapetype SEAGATE-ULTRIUM-LTO {
- comment "SEAGATE ULTRIUM 06242 LTO, compression off"
- length 99584 mbytes
- filemark 0 kbytes
- speed 11288 kps
-}
-
-# dumptypes
-#
-# These are referred to by the disklist file. The dumptype specifies
-# certain parameters for dumping including:
-# auth - authentication scheme to use between server and client.
-# Valid values are "bsd", "krb4", "krb5" and "ssh".
-# Default: [auth bsd]
-# comment - just a comment string
-# comprate - set default compression rate. Should be followed by one or
-# two numbers, optionally separated by a comma. The 1st is
-# the full compression rate; the 2nd is the incremental rate.
-# If the second is omitted, it is assumed equal to the first.
-# The numbers represent the amount of the original file the
-# compressed file is expected to take up.
-# Default: [comprate 0.50, 0.50]
-# compress - specify compression of the backed up data. Valid values are:
-# "none" - don't compress the dump output.
-# "client best" - compress on the client using the best (and
-# probably slowest) algorithm.
-# "client fast" - compress on the client using fast algorithm.
-# "client custom" - compress using your custom client compression program.
-# use client_custom_compress "PROG" to specify
-# the custom compression program.
-# PROG must not contain white space.
-# "server best" - compress on the tape host using the best (and
-# probably slowest) algorithm.
-# "server fast" - compress on the tape host using a fast
-# algorithm. This may be useful when a fast
-# tape host is backing up slow clients.
-# "server custom" - compress using your server custom compression program.
-# use server_custom_compress "PROG" to specify
-# the custom compression program.
-# PROG must not contain white space.
-# Default: [compress client fast]
-# dumpcycle - set the number of days in the dump cycle, ie, set how often a
-# full dump should be performed. Default: from DUMPCYCLE above
-# estimate Determine the way AMANDA does it's estimate.
-# "client" - Use the same program as the dumping program,
-# this is the most accurate way to do estimates,
-# but it can take a long time.
-# "calcsize" - Use a faster program to do estimates, but the
-# result is less accurate.
-# "server" - Use only statistics from the previous run to
-# give an estimate,
-# it takes only a few seconds but the result is not
-# accurate if your disk usage changes from day to day.
-# Default: [client]
-# encrypt - specify encryption of the backed up data. Valid values are:
-# "none" - don't encrypt the dump output.
-# "client" - encrypt on the client using the program specified by
-# client_encrypt "PROG".
-# Use client_decrypt_option to specify the decrypt-
-# parameter, default is "-d".
-# PROG and decrypt-parameter must not contain white space.
-# "server" - encrypt on the server using the program specified by
-# server_encrypt "PROG".
-# Use server_decrypt_option to specify the decrypt-
-# parameter, default is "-d".
-# PROG and decrypt-parameter must not contain white space.
-# Default: [none]
-# exclude - specify files and directories to be excluded from the dump.
-# Useful with gnutar only; silently ignored by dump and samba.
-# Valid values are:
-# "pattern" - a shell glob pattern defining which files
-# to exclude.
-# gnutar gets --exclude="pattern"
-# list "filename" - a file (on the client!) containing patterns
-# re's (1 per line) defining which files to
-# exclude.
-# gnutar gets --exclude-from="filename"
-# Note that the `full pathname' of a file within its
-# filesystem starts with `./', because of the way amanda runs
-# gnutar: `tar -C $mountpoint -cf - --lots-of-options .' (note
-# the final dot!) Thus, if you're backing up `/usr' with a
-# diskfile entry like ``host /usr gnutar-root', but you don't
-# want to backup /usr/tmp, your exclude list should contain
-# the pattern `./tmp', as this is relative to the `/usr' above.
-# Please refer to the man-page of gnutar for more information.
-# If a relative pathname is specified as the exclude list,
-# it is searched from within the directory that is
-# going to be backed up.
-# Default: include all files
-# holdingdisk - should the holding disk be used for this dump. Useful for
-# dumping the holding disk itself. Default: [holdingdisk auto]
-# "never" - Never use the holding disk.
-# "auto" - Use the holding disk if possible.
-# "required" - Always use the holding disk.
-# ignore - do not back this filesystem up. Useful for sharing a single
-# disklist in several configurations.
-# index - keep an index of the files backed up. Default: [index no]
-# kencrypt - encrypt the data stream between the client and server.
-# Default: [kencrypt no]
-# maxdumps - max number of concurrent dumps to run on the client.
-# Default: [maxdumps 1]
-# maxpromoteday - max number of day for a promotion, set it 0 if you don't
-# want promotion, set it to 1 or 2 if your disk get
-# overpromoted.
-# Default: [10000]
-# priority - priority level of the dump. Valid levels are "low", "medium"
-# or "high". These are really only used when Amanda has no
-# tape to write to because of some error. In that "degraded
-# mode", as many incrementals as will fit on the holding disk
-# are done, higher priority first, to insure the important
-# disks are at least dumped. Default: [priority medium]
-# program - specify the dump system to use. Valid values are "DUMP",
-# or "GNUTAR". Default: [program "DUMP"].
-# record - record the backup in the time-stamp-database of the backup
-# program (e.g. /var/lib/dumpdates for DUMP or
-# @GNUTAR_LISTED_INCREMENTAL_DIRX@ for GNUTAR.).
-# Default: [record yes]
-# skip-full - skip the disk when a level 0 is due, to allow full backups
-# outside Amanda, eg when the machine is in single-user mode.
-# skip-incr - skip the disk when the level 0 is NOT due. This is used in
-# archive configurations, where only full dumps are done and
-# the tapes saved.
-# starttime - delay the start of the dump? Default: no delay
-# strategy - set the dump strategy. Valid strategies are currently:
-# "standard" - the standard one.
-# "nofull" - do level 1 dumps every time. This can be used,
-# for example, for small root filesystems that
-# only change slightly relative to a site-wide
-# prototype. Amanda then backs up just the
-# changes.
-# "noinc" - do level 0 dumps every time.
-# "skip" - skip all dumps. Useful for sharing a single
-# disklist in several configurations.
-# "incronly" - do only incremental dumps. This is similar
-# to strategy 'nofull', but will increase
-# the dump level as usual. Full dumps will
-# only be performed when an 'amadmin force'
-# has been issued
-# Default: [strategy standard]
-# tape_splitsize - (optional) split dump file into pieces of a specified size.
-# This allows dumps to be spread across multiple tapes, and can
-# potentially make more efficient use of tape space. Note that
-# if this value is too large (more than half the size of the
-# average dump being split), substantial tape space can be
-# wasted. If too small, large dumps will be split into
-# innumerable tiny dumpfiles, adding to restoration complexity.
-# A good rule of thumb, usually, is 1/10 of the size of your
-# tape. Default: [disabled]
-# split_diskbuffer - (optional) When dumping a split dump in PORT-WRITE
-# mode (usually meaning "no holding disk"), buffer the split
-# chunks to a file in the directory specified by this option.
-# Default: [none]
-# fallback_splitsize - (optional) When dumping a split dump in PORT-WRITE
-# mode, if no split_diskbuffer is specified (or if we somehow
-# fail to use our split_diskbuffer), we must buffer split
-# chunks in memory. This specifies the maximum size split
-# chunks can be in this scenario, and thus the maximum amount
-# of memory consumed for in-memory splitting. Default: [10m]
-#
-# Note that you may specify previously defined dumptypes as a shorthand way of
-# defining parameters.
-
-define dumptype global {
- comment "Global definitions"
- # This is quite useful for setting global parameters, so you don't have
- # to type them everywhere. All dumptype definitions in this sample file
- # do include these definitions, either directly or indirectly.
- # There's nothing special about the name `global'; if you create any
- # dumptype that does not contain the word `global' or the name of any
- # other dumptype that contains it, these definitions won't apply.
- # Note that these definitions may be overridden in other
- # dumptypes, if the redefinitions appear *after* the `global'
- # dumptype name.
- # You may want to use this for globally enabling or disabling
- # indexing, recording, etc. Some examples:
- # index yes
- # record no
- # split_diskbuffer "/raid/amanda"
- # fallback_splitsize 64m
-}
-
-define dumptype always-full {
- global
- comment "Full dump of this filesystem always"
- compress none
- priority high
- dumpcycle 0
-}
-
-# Dumptypes for gnutar
-define dumptype root-tar {
- global
- program "GNUTAR"
- comment "root partitions dumped with tar"
- compress none
- index
-# exclude list "/etc/amanda/exclude.gtar"
- priority low
-}
-
-define dumptype user-tar {
- root-tar
- comment "user partitions dumped with tar"
- priority medium
-}
-
-define dumptype user-tar-span {
- root-tar
- tape_splitsize 3 Gb
- comment "tape-spanning user partitions dumped with tar"
- priority medium
-}
-
-define dumptype high-tar {
- root-tar
- comment "partitions dumped with tar"
- priority high
-}
-
-define dumptype comp-root-tar {
- root-tar
- comment "Root partitions with compression"
- compress client fast
-}
-
-define dumptype comp-user-tar {
- user-tar
- compress client fast
-}
-
-define dumptype comp-user-tar-span {
- user-tar-span
- compress client fast
-}
-
-define dumptype holding-disk {
- global
- comment "The master-host holding disk itself"
- holdingdisk never # do not use the holding disk
- priority medium
-}
-
-define dumptype comp-user {
- global
- comment "Non-root partitions on reasonably fast machines"
- compress client fast
- priority medium
-}
-
-define dumptype comp-user-span {
- global
- tape_splitsize 5 Gb
- comment "Tape-spanning non-root partitions on reasonably fast machines"
- compress client fast
- priority medium
-}
-
-define dumptype nocomp-user {
- comp-user
- comment "Non-root partitions on slow machines"
- compress none
-}
-
-define dumptype nocomp-user-span {
- comp-user-span
- comment "Tape-spanning non-root partitions on slow machines"
- compress none
-}
-
-define dumptype comp-root {
- global
- comment "Root partitions with compression"
- compress client fast
- priority low
-}
-
-define dumptype nocomp-root {
- comp-root
- comment "Root partitions without compression"
- compress none
-}
-
-define dumptype comp-high {
- global
- comment "very important partitions on fast machines"
- compress client best
- priority high
-}
-
-define dumptype nocomp-high {
- comp-high
- comment "very important partitions on slow machines"
- compress none
-}
-
-define dumptype nocomp-test {
- global
- comment "test dump without compression, no /var/lib/dumpdates recording"
- compress none
- record no
- priority medium
-}
-
-define dumptype comp-test {
- nocomp-test
- comment "test dump with compression, no /var/lib/dumpdates recording"
- compress client fast
-}
-
-define dumptype custom-compress {
- global
- program "GNUTAR"
- comment "custom client compression dumped with tar"
- compress client custom
- client_custom_compress "/usr/bin/bzip2"
-}
-
-define dumptype server-encrypt-fast {
- global
- program "GNUTAR"
- comment "fast client compression and server symmetric encryption"
- compress client fast
- encrypt server
- server_encrypt "/usr/sbin/amcrypt"
- server_decrypt_option "-d"
-}
-
-define dumptype client-encrypt-nocomp {
- global
- program "GNUTAR"
- comment "no compression and client symmetric encryption"
- compress none
- encrypt client
- client_encrypt "/usr/sbin/amcrypt"
- client_decrypt_option "-d"
-}
-
-
-# To use gpg public-key encryption, gpg does compress with zlib by default.
-# Thus, no need to specify compress
-
-#define dumptype gpg-encrypt {
-# global
-# program "GNUTAR"
-# comment "server public-key encryption, dumped with tar"
-# compress none
-# encrypt server
-# server_encrypt "/usr/sbin/amgpgcrypt"
-# server_decrypt_option "-d"
-#}
-
-
-# network interfaces
-#
-# These are referred to by the disklist file. They define the attributes
-# of the network interface that the remote machine is accessed through.
-# Notes: - netusage above defines the attributes that are used when the
-# disklist entry doesn't specify otherwise.
-# - the values below are only samples.
-# - specifying an interface does not force the traffic to pass
-# through that interface. Your OS routing tables do that. This
-# is just a mechanism to stop Amanda trashing your network.
-# Attributes are:
-# use - bandwidth above which amanda won't start
-# backups using this interface. Note that if
-# a single backup will take more than that,
-# amanda won't try to make it run slower!
-
-define interface local {
- comment "a local disk"
- use 8000 kbps
-}
-
-#define interface le0 {
-# comment "10 Mbps ethernet"
-# use 400 kbps
-#}
-
-#define application-tool and dumptype for the amgtar application
-define application-tool app_amgtar {
- comment "amgtar"
- plugin "amgtar"
- #property "GNUTAR-PATH" "/path/to/gtar"
- #property "GNUTAR-LISTDIR" "/path/to/gnutar_list_dir"
- #default from gnutar_list_dir setting in amanda-client.conf
-}
-
-define dumptype dt_amgtar {
- program "APPLICATION"
- application "app_amgtar"
-}
-
-#define application-tool and dumptype for the amstar application
-define application-tool app_amstar {
- comment "amstar"
- plugin "amstar"
- #property "STAR-PATH" "/path/to/star"
- #property "STAR-TARDUMP" "/path/to/tardumps" # default /etc/tardumps
- #property "STAR-DLE-TARDUMP" "no"
- # if 'yes' then create a different tardump file for each DLE,
- # it is required if you do many dump in parallel (maxdump>1)
-}
-
-define dumptype dt_amstar {
- program "APPLICATION"
- application "app_amstar"
-}
-
-#define a script-tool to send an email
-define script-tool sc-email {
- comment "script-email"
- plugin "script-email"
- execute_on pre-dle-amcheck, pre-host-amcheck, post-dle-amcheck, post-host-amcheck, pre-dle-estimate, pre-host-estimate, post-dle-estimate, post-host-estimate, pre-dle-backup, pre-host-backup, post-dle-backup, post-host-backup
- execute_where server # or client
- property "mailto" "martinea"
-}
-#your dumptype must include: script "sc-email"
-#to use the script
-
-# You may include other amanda configuration files, so you can share
-# dumptypes, tapetypes and interface definitions among several
-# configurations.
-
-#includefile "/etc/amanda/amanda.conf.main"