static void
ao_rn_check_link(void)
{
- ao_rn_connected = 1 - ao_gpio_get(AO_RN_CONNECTED_PORT, AO_RN_CONNECTED_PIN, foo);
+ ao_rn_connected = 1 - ao_gpio_get(AO_RN_CONNECTED_PORT, AO_RN_CONNECTED_PIN);
}
static void
ao_rn_dbg("ao_rn top\n");
/* Select CMD mode after the device gets out of reset */
- ao_gpio_set(AO_RN_CMD_PORT, AO_RN_CMD_PIN, foo, AO_RN_CMD_CMD);
+ ao_gpio_set(AO_RN_CMD_PORT, AO_RN_CMD_PIN, AO_RN_CMD_CMD);
for (i = 0; i < 3; i++) {
ao_rn_dbg("reset device\n");
- ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, foo, 0);
+ ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, 0);
ao_delay(AO_MS_TO_TICKS(100));
/* Reboot the RN4678 and wait for it to start talking */
ao_rn_drain();
- ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, foo, 1);
+ ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, 1);
status = ao_rn_wait_for(AO_RN_REBOOT_TIMEOUT, AO_RN_REBOOT_MSG);
if (status != AO_RN_OK) {
ao_rn_dbg("reboot failed\n");
if (status != AO_RN_OK)
ao_bt_panic(4);
- ao_gpio_set(AO_RN_CMD_PORT, AO_RN_CMD_PIN, foo, AO_RN_CMD_DATA);
+ ao_gpio_set(AO_RN_CMD_PORT, AO_RN_CMD_PIN, AO_RN_CMD_DATA);
/* Wait for the hardware to finish sending messages, then clear the queue */
ao_delay(AO_MS_TO_TICKS(200));
*/
/* Select our target output pin */
- ao_enable_output(AO_RN_P3_1_PORT, AO_RN_P3_1_PIN, foo, v);
+ ao_enable_output(AO_RN_P3_1_PORT, AO_RN_P3_1_PIN, v);
/* Turn off the BT device using the SW_BTN pin */
printf("Power down BT\n"); flush();
- ao_gpio_set(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, foo, 0);
+ ao_gpio_set(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, 0);
ao_delay(AO_MS_TO_TICKS(1000));
/* And turn it back on */
printf("Power up BT\n"); flush();
- ao_gpio_set(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, foo, 1);
+ ao_gpio_set(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, 1);
/* Right after power on, poke P3_1 five times to force a
* factory reset
for (i = 0; i < 20; i++) {
v = 1-v;
ao_delay(AO_MS_TO_TICKS(50));
- ao_gpio_set(AO_RN_P3_1_PORT, AO_RN_P3_1_PIN, foo, v);
+ ao_gpio_set(AO_RN_P3_1_PORT, AO_RN_P3_1_PIN, v);
ao_led_toggle(AO_BT_LED);
}
printf("Reboot BT\n"); flush();
ao_delay(AO_MS_TO_TICKS(100));
- ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, foo, 0);
+ ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, 0);
ao_delay(AO_MS_TO_TICKS(100));
- ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, foo, 1);
+ ao_gpio_set(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, 1);
}
#if AO_RN_DEBUG
ao_serial_rn_set_speed(AO_SERIAL_SPEED_115200);
/* Reset line */
- ao_enable_output(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, foo, 0);
+ ao_enable_output(AO_RN_RST_N_PORT, AO_RN_RST_N_PIN, 0);
/* SW_BTN */
- ao_enable_output(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, foo, 1);
+ ao_enable_output(AO_RN_SW_BTN_PORT, AO_RN_SW_BTN_PIN, 1);
/* P3_7 command/data selector */
- ao_enable_output(AO_RN_CMD_PORT, AO_RN_CMD_PIN, foo, AO_RN_CMD_CMD);
+ ao_enable_output(AO_RN_CMD_PORT, AO_RN_CMD_PIN, AO_RN_CMD_CMD);
ao_enable_input(AO_RN_CONNECTED_PORT, AO_RN_CONNECTED_PIN, AO_EXTI_MODE_PULL_NONE);
ao_exti_setup(AO_RN_CONNECTED_PORT, AO_RN_CONNECTED_PIN,