[[!meta title="TeleMini"]]
# TeleMini
This is a very small, baro-only recording dual-deploy altimeter for
model rocketry with integrated telemetry link.
Version 3.0 is back from fabrication and are ready for sale. Units are
available from the [Garbee and Garbee](http://shop.gag.com) web store.
For the latest TeleMini firmware and related ground station software, please
visit the [AltOS](../AltOS) page on this site.
Here's two photos of v3.0, top and bottom:
## Features ##
### User View ###
* Recording altimeter for model rocketry
* Supports dual deployment (can fire 2 ejection charges)
* 70cm ham-band transceiver for telemetry downlink
* Barometric pressure sensor good to 100k feet MSL
* Designed to use a single LiPo rechargeable battery
* 512kB flight data storage
* 1.7 x 0.5 inch board designed to fit inside 18mm airframe coupler tube
### Developer View ###
* Hardware Features
* [ST STM32F042G6](http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f0-series/stm32f0x2/stm32f042g6.html) system on chip
* ARM Cortex-M0 MCU
* 32k Flash
* 6k RAM
* USB 2.0
* digital I/O
* [TI CC1200](http://www.ti.com/product/cc1200) High Performance RF Transceiver for Narrowband Systems
* [Measurement Specialties MS5607](http://www.te.com/usa-en/product-CAT-BLPS0035.html) pressure sensor
* [Macronix MX25L4006E](http://www.macronix.com/Lists/Datasheet/Attachments/5087/MX25L4006E,%203V,%204Mb,%20v1.6.pdf) 512kB serial flash memory
* Software Features
* Written mostly in C with some ARM assembler
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* [SDCC](http://sdcc.sourceforge.net/) compiler and source debugger
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2 or later](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
## Older Versions ##
[Version 1.0](v1.0). Same width (0.5 inches), but doesn't have the
rear two mounting holes so it's a bit shorter (1.5 inches instead of
1.67 inches).
## Artifacts ##
There is a single manual for TeleMini and all other Altus Metrum products,
which is available in [html](../AltOS/doc/altusmetrum.html) and
[pdf](../AltOS/doc/altusmetrum.pdf) formats.
An outline of the board with drill hole locations is available in
[pdf](../AltOS/doc/telemini-v3-outline.pdf) format.
The hardware design files can be found on [git.gag.com](http://git.gag.com)
in the project [hw/telemini](http://git.gag.com/?p=hw/telemini;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
of the files for Production PCB version 3.0 in more easily readable form.
* [schematic](v3.0/telemini-sch.pdf)
* [pcb artwork](v3.0/telemini-pcb.pdf)
* [bill of materials](v3.0/partslist.csv)